[SunHELP] (no subject)

[Hannes Stiebitzhofer]

Hi,

I have a Ultra 10 with 512 MB RAM, which is actually not okay. Until recently
it detected 256MBs of RAM and did fine under this circumstances. Today it
startet to detect 512MB and now doesn't come up any more. Any ideas beside
getting new DIMMs?

Best,
Hannes


Setting diag-switch? because of L1-D keyboard command.

%o0 = 0000.0000.0000.2001

Executing Power On SelfTest

@(#) Sun Ultra 5/10 (Darwin) POST 2.2.9 (Build No. 502) 17:54 on 02/19/98

CPU: UltraSPARC-LC (MHz: 301 Ecache Size:  512KB)

Init POST BSS
        Init System BSS
NVRAM
        NVRAM Battery Detect Test
        NVRAM Scratch Addr Test
        NVRAM Scratch Data Test
DMMU TLB Tags
        DMMU TLB Tag Access Test
DMMU TLB RAM
        DMMU TLB RAM Access Test
Probe Ecache
        Probe Ecache
Ecache Tests
        Ecache RAM Addr Test
        Ecache Tag Addr Test
All CPU Basic Tests
        V9 Instruction Test
        CPU Soft Trap Test
        CPU Softint Reg and Int Test
All Basic MMU Tests
        DMMU Primary Context Reg Test
        DMMU Secondary Context Reg Test
        DMMU TSB Reg Test
        DMMU Tag Access Reg Test
        IMMU TSB Reg Test
        IMMU Tag Access Reg Test
All Basic Cache Tests
        Dcache RAM Test
        Icache RAM Test
Sabre MCU Control & Status Regs Init and Tests
        Init Sabre MCU Control & Status Regs
                Initializing SC registers in SabreIO
Memory Probe and Init
        Probe Memory
WARNING: DIMM Mismatch Bank 0
slot 0 upper stack :      0MB bottom stack :    128MB
slot 1 upper stack :    128MB bottom stack :    128MB
Memory used: upper stack :        0MB bottom stack :    256MB
                bank 2:   0MB
INFO: MC0 = 0x00000000.80001192, MC1 = 0x00000000.06459acb
        Ecache Access Test
        Malloc Post Memory
        Memory Addr with Ecache
        Load Post In Memory
        Run POST from MEM
        .........
loaded POST in memory
        Map PROM/STACK/NVRAM in DMMU
        Update Master Stack/Frame Pointers
All FPU Basic Tests
        FPU Regs Test
        FPU Move Regs Test
UPA Data Bus Line Test
Memory Tests
        Init Memory
        WARNING: DIMM Mismatch Bank 0
         128MB DIMM1
         128MB DIMM2
................................................................................
................................................................................
................................................................................
........
        WARNING: DIMM Mismatch Bank 0
           0MB DIMM1
         128MB DIMM2

                INFO:      0MB at bank 2 stack 0
                INFO:      0MB at bank 2 stack 1
        ECC Memory Addr Test
        WARNING: DIMM Mismatch Bank 0
         128MB DIMM1
         128MB DIMM2
        WARNING: DIMM Mismatch Bank 0
           0MB DIMM1
         128MB DIMM2
                INFO:      0MB at bank 2 stack 0
                INFO:      0MB at bank 2 stack 1
All Basic Sabre MMU Tests
        Init Sabre
        Interrupt Map (short) Reg Test
        Interrupt Set/Clr Reg Test
        Sabre IOMMU Regs Test
        Sabre IOMMU RAM Address Test
        Sabre IOMMU CAM Address Test
        PBMA PCI Config Space Regs Test
        PBMA Control/Status Reg Test
        PBMA Diag Reg Test
        Sabre IO Regs Test
All Advanced CPU Tests
        IU ASI Access Test
        FPU ASI Access Test
All CPU Error Reporting Tests
        CPU Data Access Trap Test
        CPU Addr Align Trap Test
        DMMU Access Priv Page Test
        DMMU Write Protected Page Test
All Advanced Sabre IOMMU Tests
        Init Sabre
        Consist DMA Rd, IOMMU miss Ebus Test
All Basic Cheerio Tests
        Cheerio Ebus PCI Config Space Test
        Cheerio Ethernet PCI Config Space Test
        Cheerio Init
All Sabre IOMMU Error Reporting Tests
        Init Sabre
        PIO Read, Master Abort Test
        PIO Read, Target Abort Test


Status of this POST run:        PASS
manfacturing mode=OFF
Time Stamp [hour:min:sec] 17:56:26  [month/date year] 01/02 2002




Power On Selftest Completed
Software Power ON0.0000.0000.0000 ffff.ffff.f00b.4448 0002.3333.0200.001b

@(#) Sun Ultra 5/10 UPA/PCI  3.11 Version 9 created 1998/03/06 10:31
Clearing E$ Tags  Done
Clearing I/D TLBs Done
Probing Memory Done
MEM BASE = 0000.0000.0000.0000
MEM SIZE = 0000.0000.1000.0000
11-Column Mode Enabled
MMUs ON
Copy Done
PC = 0000.01ff.f000.1ffc
PC = 0000.0000.0000.2040
Decompressing into Memory Done
Size = 0000.0000.0006.e160
ttya initialized
Reset Control: BXIR:0 BPOR:0 SXIR:0 SPOR:1 POR:0
UltraSPARC-IIi 2-2 module
Probing Memory Bank #0 256 + 256 : 512 Megabytes
Probing Memory Bank #2   0 +   0 :   0 Megabytes
Data Access Error