[SunHELP] QFE hme

[Magnus Abrante]

I dont really understand your problem, but it sounds like you are
mixing HME cards with QFE cards, the interfaces on a QFE card are 
called qfe0 to qfe3. Thus, try:

ifconfig qfe0 plumb
ifconfig qfe0 inet <something> netmask <something> up

regards,

         //Magnus Abrante
/* This is my opinion and not the one of my employer */

> Hello there.
> I would like to ask for your help, if you don't mind.
> 
> Well, I have an Ultra2. I put a QFE card in it and then installed
> Solaris 8 1/001
> This is what I see from prtdiag -v
> System clock frequency: 99 MHz
> Memory size: 1024 Megabytes
> 
> ========================= CPUs =========================
> 
>                     Run   Ecache   CPU    CPU
> Brd  CPU   Module   MHz     MB    Impl.   Mask
> ---  ---  -------  -----  ------  ------  ----
>  0     0     0      296     2.0   US-II    1.1
>  0     1     1      296     2.0   US-II    1.1
> 
> 
> ========================= IO Cards =========================
> 
>      Bus   Freq
> Brd  Type  MHz   Slot  Name                              Model
> ---  ----  ----  ----  --------------------------------
> ----------------------
>  0   SBus   25     1   QLGC,isp/sd (block)               QLGC,ISP1000
>  0   SBus   25     3   SUNW,hme                          SUNW,sbus-qfe
>  0   SBus   25     3   SUNW,hme                          SUNW,sbus-qfe
>  0   SBus   25     3   SUNW,hme                          SUNW,sbus-qfe
>  0   SBus   25     3   SUNW,hme                          SUNW,sbus-qfe
>  0   SBus   25    14   SUNW,fas/sd (block)
>  0   SBus   25    14   SUNW,hme
>  0   SBus   25    14   SUNW,bpp
>  0   UPA    99    30   FFB, Double Buffered              SUNW,501-3129
> 
> No failures found in System
> ===========================
> 
> ========================= HW Revisions =========================
> 
> ASIC Revisions:
> ---------------
> SBus: sbus Rev 1
> FEPS: SUNW,hme Rev 22
> FEPS: SUNW,hme Rev 22
> FEPS: SUNW,hme Rev 22
> FEPS: SUNW,hme Rev 22
> FEPS: SUNW,hme Rev 22
> 
> FFB Hardware Configuration:
> -----------------------------------
>         Board rev: 3
>         FBC version: 0x1
>         DAC: Brooktree 9068, version 4
>         3DRAM: Mitsubishi 1309, version 3
> 
> System PROM revisions:
> ----------------------
>   OBP 3.25.0 1999/12/03 11:35   POST 3.3.8 1998/11/16 01:42
> 
> But when I try to set up the card as per maunal, i.e.,  grep qfe
> /etc/path_to_inst
> I get nothing,.
> Now, when I do a grep hme /etc/path_to_inst I get the following:
> 
> "/sbus at 1f,0/SUNW,hme at e,8c00000" 0 "hme"
> "/sbus at 1f,0/SUNW,hme at 3,8c30000" 4 "hme"
> "/sbus at 1f,0/SUNW,hme at 3,8c20000" 3 "hme"
> "/sbus at 1f,0/SUNW,hme at 3,8c10000" 2 "hme"
> "/sbus at 1f,0/SUNW,hme at 3,8c00000" 1 "hme"
> 
> So, what I would like to know, is why this machine will not let me set
> up QFE.
> I hope you can help me out.
> 
> Thanks in advance.
> 
> David
> 
> _______________________________________________
> SunHELP maillist  -  SunHELP at sunhelp.org
> http://www.sunhelp.org/mailman/listinfo/sunhelp