[SunHELP] Problem with Netra t 1125

[hike1272-sunhelp at yahoo.com]

1. framebuffers must be setup in the obp also.  
   that is, you have to tell the netra where to
   send the output signal.
   (You haven't mentioned doing this.)

       *the obp manual is located in the answerbook2
        (part of the documentation installation)
        and on docs.sun.com

       *you need to change the obp variable,
        output-device to the physical hardware
        address of the framebuffer

2. you need to be sure the tip settings are correct.
   (the output looks like a misconfigured tip session.)
       *man tip
       *the sun solaris system administration guides
        should have this.  the guides are at the same
        locations as the obp manual.

(i rarely do either of these operations and look it up when i have to
add a framebuffer, etc.)


--- Michael Karl <mk at lexcom-net.de> wrote:
> Hello again,
> 
> I've tried an Creator-3D- and a XVR100-Card in this Netra t1125
> without
> any positive result. BTW the Netra t1125 is an Ultra 60.
> 
> The only heartbeat of this machine is (via xterm from UE10) ...
> 
> # tip hardwire
> connected
> CC CCCCCb:C
C"C 92
>              99-1$*24VV-ZVF-
> UUFF-UF*UNUVB+F*C*UWUC+C-C-C/mbTb,B6C-T6CbKbb,63Kb337C%mm3f
>
63sC.fB;33C's7C>>sfC'C'3C'?>C'C'>C:C'C'C'o,o,C'C'C?o,C:C:?C8C:C?o,>8>C:C
> ?C8o,>C1C:C?b9b:C??C9C:C?o,C:o,C8b:CC8Cb9C?C:C:C8C8C8C:
> C:C?C?C9
>
C<C?C8C:C?C?C;C8C?C?C?C;C:CC8C8C8C?CCC?C?C?CC8C?B?C<C?C?~C?B?C?C?C?C?C?C?
>
C/CC<C?C?C?C/C/CC?B?C?C?C?C/B?C?CC?C/CC?B?B?C/C/C?C?C/C?C/C/C/C?C?C?C
> C/C?C/C?
>
C?C/C/C/C?B?B?C?C/C?C?C?C?B?C?C?C?C?B?C?C?C7C?C?C?C?C?C?C?C?C?C?C?C?C?B?B?C?C
> ?C?C?C?C?C?
> 
> ... so I'm thinking, it's alive ... and not dead, but the
> terminal-settings
> are incorrect. But I've tried the default and many other settings :-(
> 
> I've no idea anymore.
> 
> Thanks Michael
> 
> > Hi Suraj,
> >
> > thanks, but it doesn't help.
> >
> > I'm thinking, somebody had changed the serial connection and I
> don't
> > think, that this configuration accepts keyboard-inputs as well.
> >
> > Normally "stop+n" resets the machine to the defaults, but what
> happen when
> > no keyboard-input change my result.
> >
> > ???
> >
> > Michael
> >>
> >> Hi,
> >> Press "stop+a" (without the quotes), u will be taken to ok prompt.
> >> then type ok set-defaults
> >>
> >> This should serve ur purpose.
> >>
> >> Regards,
> >>
> >> Suraj.
> >>
> >> -----Original Message-----
> >> From: Michael Karl [mailto:mk at lexcom-net.de]
> >> Sent: Saturday, February 07, 2004 7:26 AM
> >> To: sunhelp at sunhelp.org
> >> Subject: [SunHELP] Problem with Netra t 1125
> >>
> >>> Hello,
> >>>
> >>> I got an used Netra t 1125 for testing.
> >>>
> >>> Problem: via "tip hardwire" (Null-Modem-Connection to an Ultra
> 10) I get
> >>> only cryptical signs. The /etc/remote settings on Ultra 10 are
> correct.
> >>> (docs.sun.com - Service Manual Netra t 1120/1125)
> >>>
> >>> I'm thinking, the OBP-settings on the Netra are modified.
> >>>
> >>> HOWTO: reset or restore the default factory setting ?:-(
> >>> (With keyboard "stop+n" doesn't work)
> >>>
> >>> Thanks Michael
> >>> _______________________________________________
> >>> SunHELP maillist  -  SunHELP at sunhelp.org
> >>> http://www.sunhelp.org/mailman/listinfo/sunhelp
> _______________________________________________
> SunHELP maillist  -  SunHELP at sunhelp.org
> http://www.sunhelp.org/mailman/listinfo/sunhelp