VTUND.CONF(5)

NAME
vtund.conf - VTun(Virtual Tunnel) daemon configuration file.

DESCRIPTION

Configuration file for vtund(8) virtual tunnel daemon.

File consists of sections in the form:

    name {
      keyword value;
      keyword value;
      ..
    }

Semicolon at the end of each keyword-value pair is required, as well as grouping curly braces {}. Lines which begin with '#' characters are comments.

Name of section (name) can be one of:

options
    this section specifies general options for vtund

default
    specifies default options for all sessions

session
    (any other word except "options" and "default") introduces new session and specifies options for it.

All keyword names can be abbreviated to a minimum of 4 characters.

GENERAL OPTIONS

This section, named options, specifies general options to use by vtund(8). Possible keywords are:

type stand|inetd
    server type. vtund(8) can operate in standalone mode (stand), that is the default, or be invoked from inetd(8).

port portnumber
    server port number to listen on or connect to. By default, vtund(8) uses port 5000.

bindaddr list
    server listen address. Used to force vtund to bind to the specific address and port in server mode. Format:
      bindaddr {
       option value;
      };

    bindaddr options:

    iface if_name
        use interface address if_name as the bind address.

    addr addr
        bind address. Can be either IP address or host name.

timeout seconds
    General timeout.

persist yes|keep|no
    persist mode. If yes, the client will try to reconnect to the server after connection termination. If keep, the client will not remove and re-add the tunXX or tapXX device when reconnecting. If no, the client will exit (default). This option is ignored by the server.

syslog number|name
    syslog facility specification, either numeric or name (from syslog (3)).

ppp path
    path to pppd(8) program. Can be used in session sections.

ifconfig path
    path to ifconfig(8) program. Can be used in session sections.

route path
    path to route(8) program. Can be used in session sections.

ip path
    path to iproute(8) program. Can be used in session sections.

firewall path
    program for the firewall setup.

All the ppp, ifconfig, route and firewall parameters can specify a filename for corresponding program or equivalent (or shell script). This parameters are used in session sections to setup network interfaces.

SESSION OPTIONS

Session options can be specified inside session section or inside default section. Default parameters apply to any session section but can be overwritten there. Parameters are:

passwd secret
    password for authentication. This should be the same in client and server.

type type
    type of tunnel. Possible tunnel types are:

    tun IP tunnel (no PPP, Ether etc headers)

    ether
        Ethernet tunnel

    tty serial tunnel (PPP, SLIP etc)

    pipe
        pipe tunnel

    Default tunnel type is tty. This option is ignored by client.

device dev
    network device to use. You can choose tapXX for ether tunnel or tunXX for tun tunnel. By default vtund(8) will automatically select available device.

proto tcp|udp
    protocol to use. By default, vtund(8) will use TCP protocol. UDP is recommended for ether and tun tunnels only. This option is ignored by the client.

timeout secounds
    Connect timeout.

compress method[:level]
    specifies compression method to use. Compression methods includes:

    no  no compression

    yes default compression method

    zlib
        ZLIB compression

    lzo LZO compression (if compiled in)

    You can also specify level of compression using one digit (1 is best speed, 9 is best compression ratio). This option ignored by the client.

encrypt yes|no
    enable or disable encryption. This option ignored by the client.

keepalive yes|no
    enable or disable connection keep-alive. This option is ignored by the client.

stat yes|no
    enable or disable statistics. If enabled vtund(8) will log statistic counters to /var/log/vtund/session_X every 5 minutes.

speed kbps
    specifies speed of the connection in kilobits/second. Valid values for kbps are 8,16,32,64,128,256,etc. 0 (the default) means maximum possible speed without shaping. You can specify speed in form in:out, where in is speed to client, out - from the client. Single number means the same speed for in and out. This option ignored by the client.

srcaddr list
    local (source) address. Used to force vtund to bind to the specific address and port. Format:
      srcaddr {
       option value;
       option value;
       ..
      };

    srcaddr options:

    iface if_name
        use interface address if_name as the source address.

    addr addr
        source address. Can be either IP address or host name.

    port portnumber
        source port.

multi value
    control multiple connections. value can be yes or allow to allow multiple connections, no or deny to deny them or killold to allow new connection and kill old one. Ignored by the client.

up list
    list of programs to run after connection has been established. Used to initialize protocols, devices, routing and firewall. This option looks like whole section inside of session section. Format:
     up {
       option value;
       option value;
       ..
     };

    Options inside up (and down) blocks:

    program path arguments [wait]
        run specified program. path is the full path to the program, arguments is all arguments to pass to it (enclosed in double quotes). If wait specified, vtund will wait program termination. Special characters that can be used inside arguments parameter:

        ' (single quotes) - group arguments
        \ (back slash) - escape character
        %d - TUN or TAP device or TTY port name
        %% (double percent) - same as %d
        %A - Local IP address
        %P - Local TCP or UDP port
        %a - Remote IP address
        %p - Remote TCP or UDP port

    ppp arguments
        run program specified by ppp statement in options section. All special character described above are valid in arguments here.

    ifconfig arguments
        run program specified by ifconfig statement in options section.

    route arguments
        run program specified by route statement in options section.

    ip arguments
        run program specified by ip statement in options section.

    firewall arguments
        run program specified by firewall statement in options section.

down list
    list of programs to run after connection has been terminated. It is similar to up parameter above. Format:
     down {
       option value;
       option value;
       ..
     };

NOTES
Options ignored by the client are supplied by the server at the run time or are used only on the server side.

SEE ALSO
vtund(8), inetd(8), ifconfig(8), route(8), pppd(8), syslog(3), zlib(3).

AUTHOR
Vtund written by Maxim Krasnyansky <max_mk@yahoo.com>. This manual page was derived from comments in config file by Michael Tokarev <mjt@tls.msk.ru>