# oscam.server

Section: File Formats (5)
Index Return to Main Contents

## NAME

oscam.server - reader configuration file for OSCam

## SYNOPSIS

The server configuration file for OSCam contains reader parameters. sections in oscam.server are recurring (more than one reader possible). At least one [reader] section is required.

## DESCRIPTIONS

### The [reader] section

label = name

  name for reader, required

enable = 0|1

  0 = deactivate reader, default:1

description = text

  description of reader, default:none

protocol = reader protocol

  reader protocol, required:

  camd35|cs357x
  cccam
  cs378x
  constcw
  gbox
  ghttp
  internal
  mouse
  mp35
  newcamd|newcamd525
  newcamd524
  pcsc
  radegast
  scam
  sc8in1
  serial
  smargo
  smartreader

device = [<readertype>;]serial:serialnum|bus:device|
<device|device:slot>|
<ip|hostname>,<port>[,<lport>]|
<ip|hostname>,<gboxpport>|
<ip|hostname>,<scamport>|
pcsc|
<0|1>>|
constantcw

  define local or remote reader

  readertype: set reader type

  SR: Smartreader+ (default)
  Infinity: Infinity USB
  TripleP1: Smargo Triple Reader port 1
  TripleP2: Smargo Triple Reader port 2
  TripleP3: Smargo Triple Reader port 3

  bus:device: bus name and device name of the Smartreader+ or
  Infinity USB (get the names with lsusb 'Bus'
  and 'Device')

  serialnum: serial number of reader of the Smartreader+ or
  Infinity USB

  device: device name

  device:slot: device name and slot number sc8in1 [1-8]
  (only one SC8in1 reader supported)

  ip|hostname: IP address or host name

  port: TCP/IP port

  lport: remapping to local TCP/IP port

  gboxpport: UDP port for remote gbox peer

  PCSC: number of PCSC reader, starting with 0

  0|1: for Coolstream HD-1 STB only: select reader 0 or
  reader 1

  constantcw: constant CW file name

  constant CW file format:

  • standard format

    CAID:Provider ID:Service ID:PMT ID:ECM PID::key (16 Bytes seperated by spaces)

    example: 1234:123456:1234:2345:3456::00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F

  • extended OScam format

    CAID:Provider ID:Service ID:PMT ID:ECM PID:Video PID:key (16 Bytes seperated by spaces)

    example: 1234:123456:1234:2345:3456:7890:00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F

detect = [!]CD|[!]DSR|[!]CTS|[!]RING|[!]NONE|[!]gpio[1-7]

  status detect of card, NONE = no detection, ! = inverse, default:CD

cardmhz = mhz

  set standard SC frequency in units of 10 kHz, for Irdeto SC set to 600 mhz, for Dreambox DM800 / DM8000 set to 2700 mhz, for Dreambox DM7025 set to 8300 mhz, for older PowerPC Dreambox STBs set to 3150 mhz, refer to OVERCLOCKING, default:357

mhz = frequency

  set reader frequency in units of 10 kHz, if mhz > cardmhz you are in overclocking mode. For Smargo readers and Dreambox internal readers frequency will be set by ATR if autospeed is set to 1, default:357

autospeed = 0|1

  1 = sets mhz according to ATR. Currently only used for smartreader, Smargo and Dreambox internal protocol, other readers will be adapted to use this parameter as well. If You wan't to overclock you're card set it to 0, default:1

deprecated = 0|1

  First the SC will be initialized in normal mode. If it fails, the SC will be automatically reverted to deprecated mode, so that the SC speed will not be changed and the communication will remain on normal ATR speed of 9600 baud.

  1 = use deprecated SC mode only, default:0

mode = mode

  set card init mode for AzBox internal reader, default:none

smargopatch = 0|1

  1 = enable workaround for Smartreader+ reader until native mode works, default:0

sc8in1_dtrrts_patch = 0|1

  1 = enable fix for SC8in1/MCR DTR/RTS kernel bug, default:0

use_gpio = 0|1

  1 = use GPIO to init the reader. This needs to be set on WRT54G router, default:0

ins2e06 = payload

  add check control for pin payload (4 hex bytes) for NDS Videoguard 2 SCs, valid for physical readers only, default:none

ins7e = payload

  add 26 hex-bytes payload for NDS Videoguard 2 SCs, valid for physical readers only, default:none

ins7e11 = TA1 byte

  set TA1 byte for NDS Videoguard 2 SCs, valid for physical readers only, default:none

fix07 = 0|1

  1=enable 0x07 fix for NDS Videoguard 2 SCs, valid for physical readers only, default:1

force_irdeto = 0|1

  1 = force Irdeto SC mode even if RSA key is set for Irdeto tunnled Nagravion SC, default:0

nagra_read = 0|1|2

  read Nagravison records (on NCMED SCs only):

  0 = disabled (default)
  1 = read all records with expired rights
  2 = read records with valid rights only

rsakey = RSA key

  RSA key for Nagravision/Tiger SCs, CAM key data for Irdeto SCs, Conax SCs, default:none

deskey = DES key

  DES key for Viaccess SCs post-processing, default:none

boxkey = box key

  box key for Nagravision SCs / CAM key for Irdeto SCs

pincode = pincode

  pincode for Conax, Cryptoworks and Viaccess SCs, default:none

fix9993 = 0|1

  1 = enable fix for 9993 error with CAID 0919 Videoguard SCs, default:0

readtiers = 0|1|2

  method to get tiers of NDS Videoguard SCs:

  0 = disabled (default)
  1 = ins70 method
  2 = ins76 method

boxid = NDS box ID

  NDS receiver box id

ndsversion = 0|1|12|2

  set NDS Videoguard version

  0 = autodetection (default)
  1 = NDS Videoguard 1
  12 = NDS Videoguard 1+
  2 = NDS Videoguard 2

aeskeys = CAID #0@provid:AES key #0 CAID #0[,AES key #1 CAID #0],...[;CAID #1@provid:AES key #0 CAID #1[,AES key #1 CAID #1],...]...

  multiple 16 bytes AES keys for Viaccess SCs (the used postprocessing AES key is specified through the D2 nano of the ECM)

  special AES keys:

  00 = do not return any CW, no AES key specified
  FF = return CW received from the S, no AES key specified

  example:

  aeskeys = 0500@012345:000102030405060708090a0b0c0d0e0f;0500@543210:000102030405060708090a0b0c0d0e0f,0,0f0e0d0c0b0a090807060504030201

key = DES key

  key for newcamd remote reader encryption

user = name

  user for remote reader

password = password

  password for remote reader

mg-encrypted = D: { <IP|hostname> { <local port> <remote port> { <password> { <level> <level> }}}}[,<local MAC address>]

  mgcamd encrypted gbox line, default MAC address = eth0

services = [!]services[,[!]<services>]...

  reader [de]assignment to service group, default=none

caid = <CAID>[&<mask>][:<target CAID>][,<CAID>[&<mask>][:target <CAID>]]...

  define and mapping of CAIDs for reader, default:all CAIDs with mask FFFF

  example: caid = 0100
  caid = 0200&ffee:0300
  caid = 0400&ff00:0500,0600
  caid = 0702,0722
  caid = 0702&ffdf (shortcut for the example above)

ident = <CAID>:<provid>[,provid]...[;<CAID>:<provid>[,provid]...]...

  set CAID and SC specific ident for reader

  example: ident = 0100:123456,234567;0200:345678,456789

class = [!]class[,[!]class]...

  set SC specific class in hex for reader

  example: class = 01,02,!1b,!2b

chid = CAID:ChID

  set SC specific ChIDs for reader, default:none

  example: chid = 0100:12

group = 1..64[,1..64]...

  reader assingment to groups, default:none, required

audisabled = 0|1

  1 = exclude reader from auto AU, default:0

auprovid = provider ID

  set provider ID to use the right reader for auto AU

  example: auprovid = 123456

disableserverfilter = 0|1

  1 = ignore caid and provid settings of reader due faulty clients, default:0

inactivitytimeout = seconds

  inactivity timeout for all TCP based remote readers, -1 = reconnect on network failure for newcamd, even in idle, default:0

reconnecttimeout = seconds

  reconnect if missing answers from a remote reader, default:30

reconnectdelay = milli-seconds

  set maximum TCP connection block delay, default:60000

connectoninit = 0|1

  1 = allow newcamd connections to be established on startup although there isn't a request yet, default:0

keepalive = 0|1

  1 = allow cs378x TCP socket to be always connected, default:0. Always on if cacheex reader type.

fallback = 0|1

  1 = define reader as fallback, standard and fallback reader must have the same group, default:0

fallback_percaid = <CAID>[:<ident>[,ident]]...[;<CAID>[:<ident>[,ident]]...]....

  use reader as fallback for defined CAIDs only, two-digit wildcard CAIDs are possible, fallback_percaid overrules fallback, default:none

  example: fallback_percaid = 1234:234567;89;10:345678

emmcache = usecache,rewrite,logging

  set EMM cache of local reader:

  usecache = 0|1||2

  0 = EMM caching disabeld (default)
  1 = enable EMM caching and save EMMs to file after
  stopping OSCam
  2 = enable EMM caching, don't save EMMs to file
  after stopping OSCam

  rewrite = determines how often one and the same EMM is
  written, default:0

  logging = EMM logging mask:

  0 = EMM logging disabled (default)
  1 = logging EMM errors
  2 = logging written EMMs
  4 = logging skipped EMMs
  8 = logging blocked EMMs
  16 = logging disabled AU

  example: emmcache = 1,3,2

cacheex = 0|1|2|3

  set cache exchange mode

  0: disable cache exchange mode (default)
  1: enable cache exchange pull mode
  2: enable cache exchange push mode for camd 3.5x / 3.57x and CCcam
  protocol
  3: enable reverse cache exchange push mode for camd 3.5x / 3.57x
  and CCcam protocol

  Identical cache exchange modes must be set on local OSCam server and remote OSCam user asccount.

  Please consider memory consumption.

cacheex_maxhop = hops

  define maximum hops for cache exchange, default=10

csp_ecm_filter = [caid][&mask][@provid][$servid],n

  cache exchange incoming ECM filter setting (mode 2 only) for Cardservproxy, default:none

cacheex_drop_csp = 0|1

  1 = drop incoming Cardservproxy cache (mode 2 only), detection is zero ecmd5, default:0

cacheex_allow_request = 0|1

  1 = allow incoming ECM request (mode 2), default:1

cacheex_allow_filter = 0|1

  1 = allow cache exchange filter (for cache exchange mode 2 only), default:1

cacheex_block_fakecws = 0|1

  1 = enable fake DCWs blocking (for cache exchange mode 2 only), get fake DCWs form oscam.fakecws, default:0

ecmwhitelist = [CAID[@provid]:]length[,length]...[;[CAID[@provid]:]length[,length]...]...

  set valid ECM length per CAID and provid in hex, default:none,provid=000000

  example: ecmwhitelist = 10,20,0a,0b
  ecmwhitelist = 0100:10,20;0200@123456:0a,4b

  In normal operation mode this parameter is not required.

ecmheaderwhitelist = [CAID[@provid]:]header[,header]...[;[CAID[@provid]:]header[,header]...]...

  set vaild ECM header per CAID and provid in hex, default:none,provid=000000

ratelimitecm = count

  number of different SIDs in ECMs allowed for an interval, default:0

ecmnotfoundlimit = count

  number of ECMs with "not found" answer until the reader will be restarted, 0 = no limit, default:0

resetcycle = count

  number of ECMs until SC reset is performed, 0 = disabled, valid for physical readers only, default:0

ratelimitseconds = seconds

  interval for rate limit, default:0

ecmunique = 0|1

  1 = enable check for matching ECM hash in ratelimit slot , default:0

srvidholdseconds = seconds

  time to keep service ID in ratelimit slot, during this time checkeding for ecmunique is disbaled, default:0

cooldown = delay,duration

  define cooldown:

  delay: delay in seconds for which the reader is allowed to do
  more ECM requests than defined by ecmratelimit,
  default: none

  duration: duration in seconds the reader needs to cooldown,
  default:none

  ratelimitecm and ratelimitseconds are required

blocknano = nano[,nano]...|all

  list of EMM-nanos to block (in hex w/o 0x) or all EMM-nanos, valid for physical readers only, default:none

  example: blocknano = 45,93,7a,ff
  blocknano = all

blockemm-u = 0|1

  1 = block unique EMMs, default:0

blockemm-s = 0|1

  1 = block shared EMMs, default:0

blockemm-g = 0|1

  1 = block global EMMs, default:0

blockemm-unknown = 0|1

  1 = block unknown types of EMMs, default:0

blockemm-bylen = [length range,length range]...

  block all types of EMMs by length, default:none

  example: blockemm-bylen = 1-10,11-

read_old_classes = 0|1 (Viaccess SCs only)

  0 = read only active entitlements 1 = read all entitlements (default)

saveemm-u = 0|1

  1 = save unique EMMs to log file, default:0

saveemm-s = 0|1

  1 = save shared EMMs to log file, default:0

saveemm-g = 0|1

  1= save global EMMs to log file, default:0

saveemm-unknown = 0|1

  1 = save unknown types of EMMs to log file, default:0

savenano = nano[,nano]....|all (obsolete)

  list of EMM-nanos to save (in hex w/o 0x) or all EMM-nanos, only valid for physical readers, default:none

  example: savenano = 45,93,7a,ff
  savenano = all

readnano = [path]filename

  write file (usually a copy of a file saved by savenano) to your smartcard, if no path is specified, the specified file is searched for in the configuration directory, only valid for physical readers, default:none

  example: readnano = write.emm
  readnano = /var/oscam/write.emm

dropbadcws = 0|1

  1 = reject bad CWs, send "not found" instead of bad CWs, default:0

disablecrccws = 0|1

  1 = disable CRC for CW, default: 0

  In normal operation mode this parameter is not required. Parameter is incompatible with DVB standard.

ident = <CAID1>[:<ident1>[,<ident2>]...][;<CAID2>[:<ident3>[,<ident4>]...]]...

  use this reader as local in loadbalancer's reader selection, default:none

lb_whitelist_services = <services>,<services>...

  reader assignement to service group for channels which may never be blocked by the loadbalancer to the reader , default=none

lb_weight = weight

  the higher the value the higher the probability for reader selection in load balacing mode, default:100

  It's an divider for the average responstime.

lb_force_fallback = 0|1

  1 = set the reader always as fallaback for load balacing without considering the reader's statistics, default:0

cccversion = <main version>.<version>.<sub version>

  set CCcam version, default:none

  example: cccversion = 1.2.34

cccmaxhops = hops

  set CCcam maximum SC distance hops, default:10

  -1 = disabled
  0 = remote local SCs only
  1 = remote local SCs and + 1 hop
  2 = remote local SCs and + 2 hops
  and so on

  After reading this SC hop will be incremented by one.

ccchop = hop

  set hop for non CCCam readers, default:0

cccreshare = hop

  set reader's CCcam reshare hop, default:0

  -1 = reshare value off cccam in global config
  0 = resharing for direct peer only
  x = resharing for direct peer and share level x

cccwantemu = 0|1

  1 = request to provide emu from CCCam server, too, default:0

ccckeepalive = 0|1

  1 = send keepalive messages to keep connection to remote CCCam server up, default:0

cccreconnect = timeout

  reconnect again after ECM request timeout in milli-seconds, default:4000

cccmindown = number

  filters all readers with hops smaller than number, default:0

gbox_reshare = level

  gbox reshare level of local cards, default:0

gbox_max_distance = distance

  maximum distance to receive gbox peer cards, default:2

gbox_max_ecm_send = number

  maximum of gbox peers ECMs will be send to, default:3

use_ssl = 0|1

  1 = use SSL for ghttp protocol, default:0

## OVERCLOCKING

•
  Dreambox and other internal readers

  For Dreambox and other internal readers the highest possible clockrate will be auto detected. The mhz parameter lets you override the values chosen by OSCam, if it differs from 357 and 358, but usually you will not set any value for mhz.

  For certain Dreamboxes (especially PPC clones) the default mhz parameter leads to slow ECM times and/or "not found" ECMs. By setting mhz to values like 200, 300, 400, ... 1600 you can find a value that works for your receiver and your card. The higher the mhz value, the slower the ECM time (strange enough).

  If you choose the value too low, your card is not recognized (no ATR or "card not supported"). If you choose the value too high, you get slow ECM times. Our experience is that either no mhz line, or a line mhz = 1000 works best.

•
  Phoenix / Smartmouse reader

  Overclocking does not work with Windows and Mac OS X. Set mhz equivalent to the frequency of the reader. OSCam can not set the frequency of the reader.

•
  Smargo Smartreader+

  Use protocol = smargo for the FDDI kernel drivers (no libusb needed) or (not recommended) use protocol = smartreader for OSCam's driver implementation based on libusb.

  Set the reader frequency with the native Smargo Smartreader+ tool (srp_tools). If not setting mhz and cardmhz, OSCam tries to set the baudrate automatically, according to the maximum speed indicated by ATR. Overclocking is possible.

OSCam tries to set the baudrate automatically. A standard serial port has limited baudrate settings, so SC overclocking might not work. When using a serial reader the best way for overclocking is connecting it to a FTDI based USB to serial port adapter.

If overclocking does not work, verify the effective baudrate in the logfile. If it deviates too much from the requested baudrate, the SC will not be recognized (no ATR) and the value for mhz should be adjusted again. The higher the baudrate, the more accurate the effective baudrate can be.

## CACHE EXCHANGE

•
  pull mode (on request: cache exchange from remote to local OSCam)

  ECM requests will be forwarded to the remote cache exchange partner. If the CW could not be found in the cache of the remote exchange partner, a not found will be answered. If the CW could not be found in the cache of the remote exchange partner but a pending ECM request is open, the request will be re-initiated after the wait time defined in cacheexwaittime.

•
  push mode (continuous: cache exchange from remote to local OSCam)

  CWs from the remote cache exchange partner will be forwarded to the local cache. Forwarding only works while the camd camd 3.5x / 3.57x or CCcam protocol connection between the local and remote OSCam has been established.

•
  reverse push mode (continuous: cache exchange from local to remote OSCam)

  CWs from the local cache will be forwarded to the remote cache exchange partner. Forwarding only works while the camd camd 3.5x / 3.57x or CCcam protocol connection between the remote and local OSCam has been established.

## EXAMPLES

•
  serial mouse compatible reader
  [reader]
  label = myserialmousereader
  detect = cd
  protocol = mouse
  device = /dev/ttyS1
  group = 1
  caid = 0100
  services = myservice,!thisservice
•
  USB mouse compatible reader
  [reader]
  label = myusbmousereader
  detect = cd
  protocol = mouse
  device = /dev/ttyUSB0
  aeskey = 0102030405060708090a0b0c0d0e0f10
  group = 2
  caid = 0200
•
  camd 3.78x reader
  [reader]
  label = mycamd378xreader
  protocol = cs378x
  device = 192.168.0.1,1234
  user = user1
  password = password1
  group = 3
•
  newcamd reader
  [reader]
  label = mynewcamdreader
  protocol = newcamd
  key = 0102030405060708091011121314
  device = 192.168.0.2,2345
  user = user2
  password = password2
  group = 4
•
  CCcam reader
  [reader]
  label = mycccamreader
  protocol = cccam
  device = 192.168.0.3,3456
  user = user3
  password = password3
  group = 5
  caid = 0300,0400,0500
  cccversion = 1.2.3
•
  PCSC reader

  [reader]
  label = mypcscreader
  protocol = pcsc
  device = 0
  aeskey = 0102030405060708090a0b0c0d0e0f10
  group = 6
  caid = 0600

•
  Smargo Smartreader+

  [reader]
  label = mysmartreader
  protocol = smartreader
  device = 001:002
  aeskey = 0102030405060708090a0b0c0d0e0f10
  group = 7
  caid = 0700

•
  internal reader

  [reader]
  label = myinternalreader
  protocol = internal
  device = /dev/sci0
  group = 8
  caid = 0800

•
  sc8in1 reader

  [reader]
  label = mysc8in1reader
  protocol = sc8in1
  device = /dev/ttyUSB0:1
  group = 9
  caid = 0900

•
  constant CW

  [reader]
  label = myconstantcw
  protocol = constcw
  device = /var/keys/constant.cw
  group = 10

•
  gbox reader

  [reader]
  label = mygboxreader
  protocol = gbox
  device = 192.168.0.4,45678,56789
  user = user4
  password = password4
  group = 11
  caid = 1100

## SEE ALSO

list_smargo(1), oscam(1), oscam.ac(5), oscam.cacheex(5), oscam.cert(5), oscam.conf(5), oscam.dvbapi(5), oscam.fakecws(5), oscam.guess(5), oscam.ird(5), oscam.provid(5), oscam.ratelimit(5), oscam.services(5), oscam.srvid(5), oscam.srvid2(5), oscam.tiers(5), oscam.user(5), oscam.whitelist(5)

## Index

NAME
SYNOPSIS
DESCRIPTIONS
  The [reader] section
OVERCLOCKING
CACHE EXCHANGE
EXAMPLES
SEE ALSO