| Red Hat Linux 6.2: The Official Red Hat Linux Reference Guide | ||
|---|---|---|
| Prev | Chapter 2. System Administration | Next |
When things go wrong, there are several ways to work on fixing them. However, they require that you understand the system well. We will present the ways that you can boot into rescue modes where you can use your own knowledge to rescue the system.
Rescue mode is a term used to describe a method of booting a small Linux environment completely from a diskette, CD or other method.
What follows in this section may help you recover from a problem at some point.
As the name implies, rescue mode is there to rescue you from something. In normal operation, your Red Hat Linux system uses files located on your system's hard drive to do everything -- run programs, store your files, and more.
However, there may be times when you are unable to get Linux running completely enough to access its files on your system's hard drive. By using rescue mode, it's possible to access the files stored on your system's hard drive, even if you can't actually run Linux from that hard drive.
Normally, you'll need to get into rescue mode for one of two reasons:
You are unable to boot Linux, and you'd like to fix it.
You are having hardware or software problems, and you want to get a few important files off your system's hard drive.
Let's take a closer look at each of these scenarios.
Many times this is caused by the installation of another operating system after you've installed Red Hat Linux. Some other operating systems assume that you have no other operating systems on your computer, and overwrite the Master Boot Record (or MBR) that originally contained the LILO bootloader. If LILO is overwritten in this manner, you're out of luck -- unless you can get into rescue mode.
There can be as many different situations under this category as there are systems running Linux. Things like failing hard drives and forgetting to run LILO after building a new kernel are just two instances that can keep you from booting Red Hat Linux. If you can get into rescue mode, you might be able to resolve the problem -- or at least get copies of your most important files.
To boot your system in rescue mode, enter the following parameter at the installation boot prompt:
boot: linux rescue |
You can get to the installation boot prompt in one of these ways:
By booting your system from the diskette or CD-ROM that came with your Red Hat Linux boxed set.
By booting from a network or PCMCIA boot diskette. These methods assume your network connection is working and require you to identify the network host and transfer type. For an explanation of how to specify this information, see "Installing over the Network" in Chapter 10.
Once you have your system in rescue mode, a prompt appears:
bash# |
From this prompt, you can run the commands listed below:
anaconda gzip mkfs.ext2 ps badblocks head mknod python bash hwclock mkraid python1.5 cat ifconfig mkswap raidstart chatter init mlabel raidstop chmod insmod mmd rcp chroot less mmount rlogin clock ln mmove rm collage loader modprobe rmmod cp ls mount route cpio lsattr mpartition rpm dd lsmod mrd rsh ddcprobe mattrib mread sed depmode mbadblocks mren sh df mcd mshowfat sync e2fsck mcopy mt tac fdisk mdel mtools tail fsck mdeltree mtype tar fsck.ext2 mdir mv touch ftp mdu mzip traceroute genhdlist mformat open umount gnome-pty-helper minfo pico uncpio grep mkdir ping uniq gunzip mke2fs probe zcat |
However, if your root filesystem is undamaged, you can mount it and then run any standard Linux utility. For example, suppose your root filesystem is in /dev/hda5. Here's how to mount this partition:
mount -t ext2 /dev/hda5 /foo |
Where /foo is a directory that you have created.
Now you can run chroot, fsck, man, and other utilities. At this point, you are running Linux in single-user mode.
If you don't know the names of your Linux partitions, you can guess: mounting non-existent partitions will do no harm.
You may be able to boot single-user mode directly. If your system boots, but does not allow you to log in when it has completed booting, try rebooting and specifying one of these options at the LILO boot prompt:
LILO boot: linux single LILO boot: linux emergency |
In single-user mode, you computer boots to runlevel 1. Your local filesystems will be mounted but your network will not be activated. You get a usable system maintenance shell.
In emergency mode, you are booted into the most minimal environment possible. The root filesystem will be mounted read-only and almost nothing will be set up. The main advantage of this over linux single is that your init files are not loaded. If init is corrupted or not working, you can still mount filesystems to recover data that could be lost during a re-installation.
Have you ever rebuilt a kernel and, eager to try out your new handiwork, rebooted before running LILO? And you didn't have an entry for an older kernel in lilo.conf? Read on…
In many cases, it's possible to boot your Red Hat Linux/Intel system from the Red Hat Linux boot disk with your root filesystem mounted and ready to go. Here's how:
Enter the following command at the boot disk's boot: prompt:
linux single root=/dev/hdXX initrd= |
(Replace the XX in /dev/hdXX with the appropriate letter and number for your root partition.)
What does this do? First, it starts the boot in single-user mode, with the root partition set to your root partition. The empty initrd specification bypasses the installation-related image on the boot disk, which will cause you to enter single-user mode immediately.
Is there a downside? Unfortunately, yes. Because the kernel on the Red Hat Linux boot disk only has support for IDE built-in, those of you with SCSI-based systems won't be able to use this trick. In that case, you'll have to use the boot/rescue disk combination mentioned above.