Patch Name: PHSS_21234 Patch Description: s700_800 10.X OV OB3.10 patch - CS packet Creation Date: 00/03/14 Post Date: 00/03/17 Hardware Platforms - OS Releases: s700: 10.00 10.01 10.10 10.20 s800: 10.00 10.01 10.10 10.20 Products: OmniBackII A.03.10 Filesets: OMNIBACK-II.OMNI-CS Automatic Reboot?: No Status: General Superseded Critical: No Path Name: /hp-ux_patches/s700_800/10.X/PHSS_21234 Symptoms: PHSS_21234: Id = NSMex02885 BSM reports unexpected close message during backup preview. Id = NSMex02929 Bad performance of Informix logical logs restore. Id = NSMex03097 Copy session of write-protected tape is aborted and cleaning tape is requested in the source tape drive. Id = NSMex02931 Too many backup sessions running in parallel. Id = NSMex02964 License is not recognized on a Cell Manager system with multiple lan cards although it has been prepared for one of the lan cards IP address. Id = NSMex03110 Backup fails with an error: "Could not connect to inet in order to start BMA". Id = NSMex02738 Bad backup performance after upgrade from OmniBack II 2.55 or 3.00. Id = NSMex02639, NSMex03017 "omnirpt -report fs_not_conf" gives incorrect output. Id = NSMex03144 Mounting of media fails with an error: "Volume not found of this type". Id = NSMex03052, JAGac40383 Filesystem disk agents of a host backup are not started until the pre/post-exec of the host object is completed. PHSS_19519: Id = HSLco16368 HP SureStoreE Disk Array XP256 is not supported by OmniBack II to perform a split mirror backup. This patch does not fix any other problem. Defect Description: PHSS_21234: Id = NSMex02885 BSM reports unexpected close message during backup preview even if Disk Agent was completed successfully. Resolution: Counting of processed data size improved. Id = NSMex02929 There is a consistent delay of 30 seconds between each logical log restore. Resolution: Fix is implemented in Restore Session Manager. Id = NSMex03097 Copy session is aborted when copying a write-protected tape. When write-protected tape in the source drive is checked, the cleaning tape for that drive is requested and the following message appears: "Cleaning tape requested by device . Please clean the drive.". Resolution: The cleanme signal is now processed correctly. Id = NSMex02931 It is not possible to have more than 50 sessions running in parallel with OmniBAck II 3.10. Resolution: The maximum number of session running in parallel is set to 200. Part of the SSPUX310_004. Id = NSMex02964 On some systems ioctl command returns 0 as the IP address of some of the lan cards. This value has been used as the end of IP address list and OmniBack II rejects the license if it is prepared for an IP address that is listed after "0" address. Resolution: "0" addresses are not added to the list of valid system IP addresses. This way license checking searches complete IP address list until if finds the IP address that the license has been prepared for. Id = NSMex03110 If more than one Media Agent is used in one session and they are located on the same Novell NetWare client, then the backup fails with an error: "Could not connect to inet in order to start BMA". Resolution: Delay for starting Media Agents increased. Id = NSMex02738 Performance degrated by up to 50% after upgrade from OmniBack II 2.55 or 3.10. Resolution: Redundant update of the objects removed. Id = NSMex02639, NSMex03017 "omnirpt -report fs_not_conf" gives incorrect output. Resolution: Processing of "allbdf" output changed. Id = NSMex03144 After the confirmation of mount request for GRAU DAS or Storage Tek ACS Library, OmniBack II tries to load "" (empty string) medium. Library returns an error that such a volume does not exist. Resolution: BSM rechecks medium allocation after the mount request confirmation. Id = NSMex03052, JAGac40383 If a datalist contains a host object with pre/post-exec script, disk agents for the filesystem objects of that host will not start until the script execution is complete. This is not suitable if the script doesn't need to be started for all filesystems. Resolution: A new global option is introduced in order to control the behaviour of the pre/post-exec script execution. See 'Special Installation Instructions' for details on setting the global option. Part of SSPUX310_018. PHSS_19519: Id = HSLco16368 Currently OmniBack II only supports the Split Mirror Backup concept with EMC Symmetrix. After the introduction of the new HP SureStoreE Disk Array XP256, it was requested that OmniBack II also supports this disk array with the split mirror backup concept. This requires to support Oracle 8.0.x and SAP R/3 in this concept as well and in addition a new manual is needed. Resolution: The SureStoreE Agent (SSEA) was developed for HP-UX to controll the SureStoreE disk array. The Backup Session Manager, INET on HP-UX, and the NT GUI were enhanced and in addition Oracle 8.0.x and SAP integrations are supported. Also the manual "HP OpenView OmniBack II HP SureStore E Disk Array XP256 Configuration Guide" will be released. SR: 8606110994 Patch Files: /opt/omni/lbin/bsm /opt/omni/lbin/crs /opt/omni/lbin/rsm /opt/omni/lbin/dbsm /opt/omni/lbin/msm what(1) Output: /opt/omni/lbin/bsm: [TZ=GMT0 /opt/omni/lbin/bsm -version] HP OpenView OmniBack II A.03.10: BSM, internal build PHSS_21234/PHSS_21235, built on Thu Mar 9 08:48:45 2000 /opt/omni/lbin/crs: [TZ=GMT0 /opt/omni/lbin/crs -version] HP OpenView OmniBack II A.03.10: CRS, internal build PHSS_21234/PHSS_21235, built on Thu Mar 9 09:26:52 2000 /opt/omni/lbin/rsm: [TZ=GMT0 /opt/omni/lbin/rsm -version] HP OpenView OmniBack II A.03.10: RSM, internal build PHSS_21234/PHSS_21235, built on Thu Mar 9 08:50:15 2000 /opt/omni/lbin/dbsm: [TZ=GMT0 /opt/omni/lbin/dbsm -version] HP OpenView OmniBack II A.03.10: DBSM, internal buil d PHSS_21234/PHSS_21235, built on Thu Mar 9 09:18:54 2000 /opt/omni/lbin/msm: [TZ=GMT0 /opt/omni/lbin/msm -version] HP OpenView OmniBack II A.03.10: MSM, internal build PHSS_21234/PHSS_21235, built on Thu Mar 9 09:01:23 2000 cksum(1) Output: 3329964350 1154008 /opt/omni/lbin/bsm 1087513307 698171 /opt/omni/lbin/crs 2403313447 858529 /opt/omni/lbin/rsm 3008232397 1219050 /opt/omni/lbin/dbsm 4214031548 677854 /opt/omni/lbin/msm Patch Conflicts: None Patch Dependencies: None Hardware Dependencies: None Other Dependencies: None Supersedes: PHSS_19519 Equivalent Patches: PHSS_21235: s700: 11.00 s800: 11.00 Patch Package Size: 4560 KBytes Installation Instructions: Please review all instructions and the Hewlett-Packard SupportLine User Guide or your Hewlett-Packard support terms and conditions for precautions, scope of license, restrictions, and, limitation of liability and warranties, before installing this patch. ------------------------------------------------------------ 1. Back up your system before installing a patch. 2. Login as root. 3. Copy the patch to the /tmp directory. 4. Move to the /tmp directory and unshar the patch: cd /tmp sh PHSS_21234 5a. For a standalone system, run swinstall to install the patch: swinstall -x autoreboot=true -x match_target=true \ -s /tmp/PHSS_21234.depot By default swinstall will archive the original software in /var/adm/sw/patch/PHSS_21234. If you do not wish to retain a copy of the original software, you can create an empty file named /var/adm/sw/patch/PATCH_NOSAVE. WARNING: If this file exists when a patch is installed, the patch cannot be deinstalled. Please be careful when using this feature. It is recommended that you move the PHSS_21234.text file to /var/adm/sw/patch for future reference. To put this patch on a magnetic tape and install from the tape drive, use the command: dd if=/tmp/PHSS_21234.depot of=/dev/rmt/0m bs=2k Special Installation Instructions: PHSS_21234: NOTE! This Patch has to be installed on the Cell Manager host. OmniBack II server must be shutdown before installing the patch. Use the following command for shutting down the server: "/opt/omni/sbin/omnisv.sh stop". After the installation is complete, restart OmniBack II server using "/opt/omni/sbin/omnisv.sh start". NOTE! New global option has been introduced with this patch for solving the problem NSMex03052 & JAGac40383. With this option, the backup administrator can decide wether the pre/post-exec script will be started for one filesystem on the host only, or should all the filesystem disk agents wait for the pre/post-exec script to finish before starting up the filesystem backup. The option must be set on the Cell Manager system, in the file /etc/opt/omni/options/global. This is the syntax: PrePostExecOnEveryVolumeForHostBackup=<0 or 1> default: 0 If this option is set (=1), Backup Disk Agent (BDA) for each volume of host object will execute the pre/post-exec script specified. If this option is not set (=0), the Backup Session Manager (BSM) will execute preexec just prior to starting first volume BDA and postexec after last volume BDA finished. Note that for the duration of pre/post-exec scripts, the BSM will not be responding. NOTE! The patches PHSS_19519/PHSS_19520 introduce support for HP SureStore E XP256 disk array. In order to enable the HP SurStoreE Agent (SSEA) functionality,a license-to-use (B7023AA) must be installed. In addition, the following OB2 patches are required: PHSS_19523/PHSS_19524 - Core patch PHSS_20111/PHSS_20112 - Oracle8 integration patch PHSS_19525/PHSS_19526 - SSEA integration patch PHSS_19594/PHSS_19595 - SAP integration patch OMNIBACK_00010 - Windows NT Some of the patches mentioned above may be superseded by a newer patch. Please check the HP Electronic Support Center web page for latest patches available. For more information regarding the installation procedure refer to the "HP OpenView OmniBack II HP SureStore E Disk Array XP256 Configuration Guide" Patch includes the following Site Specific Patches: SSPUX310_004 SSPUX310_018