Patch Name: PHNE_25500 Patch Description: s700_800 10.20 ATM-HSC and HP-PB 3.0/6.0 cumulative patch Creation Date: 02/02/14 Post Date: 02/02/21 Hardware Platforms - OS Releases: s700: 10.20 s800: 10.20 Products: J2805AA: C.10.20.00 J2805AA: D.10.20.00 J2805AA: D.10.20.10 J2805AA: D.10.20.11 J2805AA: D.10.20.12 J2805AA: D.10.20.13 J2805AA: D.10.20.20 J2805AA: D.10.20.21 J2805AA: D.10.20.40 J2805AA: D.10.20.41 J2805AA: E.10.20.00 J2805AA: E.10.20.11 J2805AA: E.10.20.12 J2805AA: F.10.20.00 J2805AA: G.10.20.00 J2805AA: G.10.20.01 J2805AA: G.10.20.02 J2805BA: E.10.20.00 J2805BA: E.10.20.11 J2805BA: E.10.20.12 J2805BA: F.10.20.00 J2805BA: G.10.20.00 J2805BA: G.10.20.01 J2805BA: G.10.20.02 J2805BA: H.10.20.00 J2805BA: H.10.20.01 J2805BA: I.10.20.00 J2805BA: I.10.20.10 J2806BA: C.10.20.00 J2806BA: D.10.20.00 J2806BA: D.10.20.10 J2806BA: D.10.20.11 J2806BA: D.10.20.12 J2806BA: D.10.20.13 J2806BA: D.10.20.20 J2806BA: D.10.20.21 J2806BA: D.10.20.23 J2806BA: D.10.20.40 J2806BA: D.10.20.41 J2806BA: E.10.20.00 J2806BA: E.10.20.11 J2806BA: E.10.20.12 J2806BA: F.10.20.00 J2806BA: G.10.20.00 J2806BA: G.10.20.01 J2806BA: G.10.20.02 J2806CA: E.10.20.00 J2806CA: E.10.20.11 J2806CA: E.10.20.12 J2806CA: F.10.20.00 J2806CA: G.10.20.00 J2806CA: G.10.20.01 J2806CA: G.10.20.02 J2806CA: H.10.20.00 J2806CA: H.10.20.01 J2806CA: I.10.20.00 J2806CA: I.10.20.10 J2806DA: E.10.20.00 J2806DA: E.10.20.11 J2806DA: E.10.20.12 J2806DA: F.10.20.00 J2806DA: G.10.20.00 J2806DA: G.10.20.01 J2806DA: G.10.20.02 J3572BA: I.10.20.00 J3572BA: I.10.20.10 A5483A: I.10.20.10 A5513A: I.10.20.10 A5515A: I.10.20.10 J2468A: I.10.20.10 J2469A: I.10.20.10 J2499A: I.10.20.10 J2804A: I.10.20.10 J3420B: I.10.20.10 J3573A: I.10.20.10 Filesets: ATM2HSC.ATM2HSC-KRN,C.10.20.00 ATM2HSC.ATM2HSC-KRN,D.10.20.00 ATM2HSC.ATM2HSC-KRN,D.10.20.10 ATM2HSC.ATM2HSC-KRN,D.10.20.11 ATM2HSC.ATM2HSC-KRN,D.10.20.12 ATM2HSC.ATM2HSC-KRN,D.10.20.13 ATM2HSC.ATM2HSC-KRN,D.10.20.20 ATM2HSC.ATM2HSC-KRN,D.10.20.21 ATM2HSC.ATM2HSC-KRN,D.10.20.23 ATM2HSC.ATM2HSC-KRN,D.10.20.40 ATM2HSC.ATM2HSC-KRN,D.10.20.41 ATM2HSC.ATM2HSC-KRN,E.10.20.00 ATM2HSC.ATM2HSC-KRN,E.10.20.11 ATM2HSC.ATM2HSC-KRN,E.10.20.12 ATM2HSC.ATM2HSC-KRN,F.10.20.00 ATM2HSC.ATM2HSC-KRN,G.10.20.00 ATM2HSC.ATM2HSC-KRN,G.10.20.01 ATM2HSC.ATM2HSC-KRN,G.10.20.02 ATM2HSC.ATM2HSC-KRN,H.10.20.00 ATM2HSC.ATM2HSC-KRN,H.10.20.01 ATM2HSC.ATM2HSC-KRN,I.10.20.00 ATM2HSC.ATM2HSC-KRN,I.10.20.10 ATM2HSC.ATM2HSC-RUN,C.10.20.00 ATM2HSC.ATM2HSC-RUN,D.10.20.00 ATM2HSC.ATM2HSC-RUN,D.10.20.10 ATM2HSC.ATM2HSC-RUN,D.10.20.11 ATM2HSC.ATM2HSC-RUN,D.10.20.12 ATM2HSC.ATM2HSC-RUN,D.10.20.13 ATM2HSC.ATM2HSC-RUN,D.10.20.20 ATM2HSC.ATM2HSC-RUN,D.10.20.21 ATM2HSC.ATM2HSC-RUN,D.10.20.23 ATM2HSC.ATM2HSC-RUN,D.10.20.40 ATM2HSC.ATM2HSC-RUN,D.10.20.41 ATM2HSC.ATM2HSC-RUN,E.10.20.00 ATM2HSC.ATM2HSC-RUN,E.10.20.11 ATM2HSC.ATM2HSC-RUN,E.10.20.12 ATM2HSC.ATM2HSC-RUN,F.10.20.00 ATM2HSC.ATM2HSC-RUN,G.10.20.00 ATM2HSC.ATM2HSC-RUN,G.10.20.01 ATM2HSC.ATM2HSC-RUN,G.10.20.02 ATM2HSC.ATM2HSC-RUN,H.10.20.00 ATM2HSC.ATM2HSC-RUN,H.10.20.01 ATM2HSC.ATM2HSC-RUN,I.10.20.00 ATM2HSC.ATM2HSC-RUN,I.10.20.10 ATMHSC.ATMHSC-KRN,C.10.20.00 ATMHSC.ATMHSC-KRN,D.10.20.00 ATMHSC.ATMHSC-KRN,D.10.20.10 ATMHSC.ATMHSC-KRN,D.10.20.11 ATMHSC.ATMHSC-KRN,D.10.20.12 ATMHSC.ATMHSC-KRN,D.10.20.13 ATMHSC.ATMHSC-KRN,D.10.20.20 ATMHSC.ATMHSC-KRN,D.10.20.21 ATMHSC.ATMHSC-KRN,D.10.20.23 ATMHSC.ATMHSC-KRN,D.10.20.40 ATMHSC.ATMHSC-KRN,D.10.20.41 ATMHSC.ATMHSC-KRN,E.10.20.00 ATMHSC.ATMHSC-KRN,E.10.20.11 ATMHSC.ATMHSC-KRN,E.10.20.12 ATMHSC.ATMHSC-KRN,F.10.20.00 ATMHSC.ATMHSC-KRN,G.10.20.00 ATMHSC.ATMHSC-KRN,G.10.20.01 ATMHSC.ATMHSC-KRN,G.10.20.02 ATMHSC.ATMHSC-KRN,H.10.20.00 ATMHSC.ATMHSC-KRN,H.10.20.01 ATMHSC.ATMHSC-KRN,I.10.20.00 ATMHSC.ATMHSC-KRN,I.10.20.10 ATMPB.ATMPB-KRN,C.10.20.00 ATMPB.ATMPB-KRN,D.10.20.00 ATMPB.ATMPB-KRN,D.10.20.10 ATMPB.ATMPB-KRN,D.10.20.11 ATMPB.ATMPB-KRN,D.10.20.12 ATMPB.ATMPB-KRN,D.10.20.13 ATMPB.ATMPB-KRN,D.10.20.20 ATMPB.ATMPB-KRN,D.10.20.21 ATMPB.ATMPB-KRN,D.10.20.23 ATMPB.ATMPB-KRN,D.10.20.40 ATMPB.ATMPB-KRN,D.10.20.41 ATMPB.ATMPB-KRN,E.10.20.00 ATMPB.ATMPB-KRN,E.10.20.11 ATMPB.ATMPB-KRN,E.10.20.12 ATMPB.ATMPB-KRN,F.10.20.00 ATMPB.ATMPB-KRN,G.10.20.00 ATMPB.ATMPB-KRN,G.10.20.01 ATMPB.ATMPB-KRN,G.10.20.02 ATMPB.ATMPB-KRN,H.10.20.00 ATMPB.ATMPB-KRN,H.10.20.01 ATMPB.ATMPB-KRN,I.10.20.00 ATMPB.ATMPB-KRN,I.10.20.10 ATM2PCI.ATM2PCI-KRN,C.10.20.00 ATM2PCI.ATM2PCI-KRN,D.10.20.00 ATM2PCI.ATM2PCI-KRN,D.10.20.10 ATM2PCI.ATM2PCI-KRN,D.10.20.11 ATM2PCI.ATM2PCI-KRN,D.10.20.12 ATM2PCI.ATM2PCI-KRN,D.10.20.13 ATM2PCI.ATM2PCI-KRN,D.10.20.20 ATM2PCI.ATM2PCI-KRN,D.10.20.21 ATM2PCI.ATM2PCI-KRN,D.10.20.23 ATM2PCI.ATM2PCI-KRN,D.10.20.40 ATM2PCI.ATM2PCI-KRN,D.10.20.41 ATM2PCI.ATM2PCI-KRN,E.10.20.00 ATM2PCI.ATM2PCI-KRN,E.10.20.11 ATM2PCI.ATM2PCI-KRN,E.10.20.12 ATM2PCI.ATM2PCI-KRN,F.10.20.00 ATM2PCI.ATM2PCI-KRN,G.10.20.00 ATM2PCI.ATM2PCI-KRN,G.10.20.01 ATM2PCI.ATM2PCI-KRN,G.10.20.02 ATM2PCI.ATM2PCI-KRN,H.10.20.00 ATM2PCI.ATM2PCI-KRN,H.10.20.01 ATM2PCI.ATM2PCI-KRN,I.10.20.00 ATM2PCI.ATM2PCI-KRN,I.10.20.10 ATMCORE.ATMCORE-KRN,C.10.20.00 ATMCORE.ATMCORE-KRN,D.10.20.00 ATMCORE.ATMCORE-KRN,D.10.20.10 ATMCORE.ATMCORE-KRN,D.10.20.11 ATMCORE.ATMCORE-KRN,D.10.20.12 ATMCORE.ATMCORE-KRN,D.10.20.13 ATMCORE.ATMCORE-KRN,D.10.20.20 ATMCORE.ATMCORE-KRN,D.10.20.21 ATMCORE.ATMCORE-KRN,D.10.20.23 ATMCORE.ATMCORE-KRN,D.10.20.40 ATMCORE.ATMCORE-KRN,D.10.20.41 ATMCORE.ATMCORE-KRN,E.10.20.00 ATMCORE.ATMCORE-KRN,E.10.20.11 ATMCORE.ATMCORE-KRN,E.10.20.12 ATMCORE.ATMCORE-KRN,F.10.20.00 ATMCORE.ATMCORE-KRN,G.10.20.00 ATMCORE.ATMCORE-KRN,G.10.20.01 ATMCORE.ATMCORE-KRN,G.10.20.02 ATMCORE.ATMCORE-KRN,H.10.20.00 ATMCORE.ATMCORE-KRN,H.10.20.01 ATMCORE.ATMCORE-KRN,I.10.20.00 ATMCORE.ATMCORE-KRN,I.10.20.10 ATMCORE.ATMCORE-RUN,C.10.20.00 ATMCORE.ATMCORE-RUN,D.10.20.00 ATMCORE.ATMCORE-RUN,D.10.20.10 ATMCORE.ATMCORE-RUN,D.10.20.11 ATMCORE.ATMCORE-RUN,D.10.20.12 ATMCORE.ATMCORE-RUN,D.10.20.13 ATMCORE.ATMCORE-RUN,D.10.20.20 ATMCORE.ATMCORE-RUN,D.10.20.21 ATMCORE.ATMCORE-RUN,D.10.20.23 ATMCORE.ATMCORE-RUN,D.10.20.40 ATMCORE.ATMCORE-RUN,D.10.20.41 ATMCORE.ATMCORE-RUN,E.10.20.00 ATMCORE.ATMCORE-RUN,E.10.20.11 ATMCORE.ATMCORE-RUN,E.10.20.12 ATMCORE.ATMCORE-RUN,F.10.20.00 ATMCORE.ATMCORE-RUN,G.10.20.00 ATMCORE.ATMCORE-RUN,G.10.20.01 ATMCORE.ATMCORE-RUN,G.10.20.02 ATMCORE.ATMCORE-RUN,H.10.20.00 ATMCORE.ATMCORE-RUN,H.10.20.01 ATMCORE.ATMCORE-RUN,I.10.20.00 ATMCORE.ATMCORE-RUN,I.10.20.10 ATMCORE.ATMCORE-MAN,C.10.20.00 ATMCORE.ATMCORE-MAN,D.10.20.00 ATMCORE.ATMCORE-MAN,D.10.20.10 ATMCORE.ATMCORE-MAN,D.10.20.11 ATMCORE.ATMCORE-MAN,D.10.20.12 ATMCORE.ATMCORE-MAN,D.10.20.13 ATMCORE.ATMCORE-MAN,D.10.20.20 ATMCORE.ATMCORE-MAN,D.10.20.21 ATMCORE.ATMCORE-MAN,D.10.20.23 ATMCORE.ATMCORE-MAN,D.10.20.40 ATMCORE.ATMCORE-MAN,D.10.20.41 ATMCORE.ATMCORE-MAN,E.10.20.00 ATMCORE.ATMCORE-MAN,E.10.20.11 ATMCORE.ATMCORE-MAN,E.10.20.12 ATMCORE.ATMCORE-MAN,F.10.20.00 ATMCORE.ATMCORE-MAN,G.10.20.00 ATMCORE.ATMCORE-MAN,G.10.20.01 ATMCORE.ATMCORE-MAN,G.10.20.02 ATMCORE.ATMCORE-MAN,H.10.20.00 ATMCORE.ATMCORE-MAN,H.10.20.01 ATMCORE.ATMCORE-MAN,I.10.20.00 ATMCORE.ATMCORE-MAN,I.10.20.10 ATMSAM.ATMSAM-RUN,C.10.20.00 ATMSAM.ATMSAM-RUN,D.10.20.00 ATMSAM.ATMSAM-RUN,D.10.20.10 ATMSAM.ATMSAM-RUN,D.10.20.11 ATMSAM.ATMSAM-RUN,D.10.20.12 ATMSAM.ATMSAM-RUN,D.10.20.13 ATMSAM.ATMSAM-RUN,D.10.20.20 ATMSAM.ATMSAM-RUN,D.10.20.21 ATMSAM.ATMSAM-RUN,D.10.20.23 ATMSAM.ATMSAM-RUN,D.10.20.40 ATMSAM.ATMSAM-RUN,D.10.20.41 ATMSAM.ATMSAM-RUN,E.10.20.00 ATMSAM.ATMSAM-RUN,E.10.20.11 ATMSAM.ATMSAM-RUN,E.10.20.12 ATMSAM.ATMSAM-RUN,F.10.20.00 ATMSAM.ATMSAM-RUN,G.10.20.00 ATMSAM.ATMSAM-RUN,G.10.20.01 ATMSAM.ATMSAM-RUN,G.10.20.02 ATMSAM.ATMSAM-RUN,H.10.20.00 ATMSAM.ATMSAM-RUN,H.10.20.01 ATMSAM.ATMSAM-RUN,I.10.20.00 ATMSAM.ATMSAM-RUN,I.10.20.10 ATMSAM.ATMSAM-HELP,C.10.20.00 ATMSAM.ATMSAM-HELP,D.10.20.00 ATMSAM.ATMSAM-HELP,D.10.20.10 ATMSAM.ATMSAM-HELP,D.10.20.11 ATMSAM.ATMSAM-HELP,D.10.20.12 ATMSAM.ATMSAM-HELP,D.10.20.13 ATMSAM.ATMSAM-HELP,D.10.20.20 ATMSAM.ATMSAM-HELP,D.10.20.21 ATMSAM.ATMSAM-HELP,D.10.20.23 ATMSAM.ATMSAM-HELP,D.10.20.40 ATMSAM.ATMSAM-HELP,D.10.20.41 ATMSAM.ATMSAM-HELP,E.10.20.00 ATMSAM.ATMSAM-HELP,E.10.20.11 ATMSAM.ATMSAM-HELP,E.10.20.12 ATMSAM.ATMSAM-HELP,F.10.20.00 ATMSAM.ATMSAM-HELP,G.10.20.00 ATMSAM.ATMSAM-HELP,G.10.20.01 ATMSAM.ATMSAM-HELP,G.10.20.02 ATMSAM.ATMSAM-HELP,H.10.20.00 ATMSAM.ATMSAM-HELP,H.10.20.01 ATMSAM.ATMSAM-HELP,I.10.20.00 ATMSAM.ATMSAM-HELP,I.10.20.10 ATMHA.ATMHA-RUN,C.10.20.00 ATMHA.ATMHA-RUN,D.10.20.00 ATMHA.ATMHA-RUN,D.10.20.10 ATMHA.ATMHA-RUN,D.10.20.11 ATMHA.ATMHA-RUN,D.10.20.12 ATMHA.ATMHA-RUN,D.10.20.13 ATMHA.ATMHA-RUN,D.10.20.20 ATMHA.ATMHA-RUN,D.10.20.21 ATMHA.ATMHA-RUN,D.10.20.23 ATMHA.ATMHA-RUN,D.10.20.40 ATMHA.ATMHA-RUN,D.10.20.41 ATMHA.ATMHA-RUN,E.10.20.00 ATMHA.ATMHA-RUN,E.10.20.11 ATMHA.ATMHA-RUN,E.10.20.12 ATMHA.ATMHA-RUN,F.10.20.00 ATMHA.ATMHA-RUN,G.10.20.00 ATMHA.ATMHA-RUN,G.10.20.01 ATMHA.ATMHA-RUN,G.10.20.02 ATMHA.ATMHA-RUN,H.10.20.00 ATMHA.ATMHA-RUN,H.10.20.01 ATMHA.ATMHA-RUN,I.10.20.00 ATMHA.ATMHA-RUN,I.10.20.10 ATMHA.ATMHA-MAN,C.10.20.00 ATMHA.ATMHA-MAN,D.10.20.00 ATMHA.ATMHA-MAN,D.10.20.10 ATMHA.ATMHA-MAN,D.10.20.11 ATMHA.ATMHA-MAN,D.10.20.12 ATMHA.ATMHA-MAN,D.10.20.13 ATMHA.ATMHA-MAN,D.10.20.20 ATMHA.ATMHA-MAN,D.10.20.21 ATMHA.ATMHA-MAN,D.10.20.23 ATMHA.ATMHA-MAN,D.10.20.40 ATMHA.ATMHA-MAN,D.10.20.41 ATMHA.ATMHA-MAN,E.10.20.00 ATMHA.ATMHA-MAN,E.10.20.11 ATMHA.ATMHA-MAN,E.10.20.12 ATMHA.ATMHA-MAN,F.10.20.00 ATMHA.ATMHA-MAN,G.10.20.00 ATMHA.ATMHA-MAN,G.10.20.01 ATMHA.ATMHA-MAN,G.10.20.02 ATMHA.ATMHA-MAN,H.10.20.00 ATMHA.ATMHA-MAN,H.10.20.01 ATMHA.ATMHA-MAN,I.10.20.00 ATMHA.ATMHA-MAN,I.10.20.10 Automatic Reboot?: Yes Status: General Release Critical: Yes PHNE_25500: PANIC The system may panic PHNE_22586: PANIC The system may panic PHNE_21423: PANIC The system may panic PHNE_18443: PANIC The system may panic PHNE_17269: PANIC The system may panic PHNE_15346: PANIC The system may panic PHNE_14469: PANIC kernel stack overflow. Data corruption PHNE_13599: PANIC The system may panic PHNE_12751: PANIC The system may panic PHNE_11301: PANIC The system may hang or panic PHNE_10611: PANIC The system may panic if no LE_ARP_RESPONSE is received. PHNE_10151: PANIC The system may panic in ecInitAmCgPtyNmb function, this can happen when adding more than 2 destinations to an edge device and when the learp entry associated to one of the destinations is removed. The system may panic in ecTxCtrlFrame function during connection establishment and when losing connection with BUS at the same time. The system may panic in LSS_F_SAddPstMsgMult or memory may be corrupted when a new mbuf must be allocated to add the ethernet header and if the message is too short and need pading. Path Name: /hp-ux_patches/s700_800/10.X/PHNE_25500 Symptoms: PHNE_25500: - Script error while doing an OS update to B.11.11 OEUR-0601. - The EPtRf field in atm address has not been described in the atmmgr manpage. - Traffic descriptors not taken into account for LanEmul Token-Ring. - A5513A card is sometimes not claimed on reboot, on a V2200 system. - The hardware revision of a PCI ATM card is not stored in the ift structure. - Spinlock deadlock in IAM_F0_lrput() due to a lock not being released. - "atmconfig show -n" on a non-existent CIP interface causes system to panic. - Data page fault in function LVC_F0_remove. - When Token ring is configured for multicast on LANE v1, it does not work. - Data page fault in asAsdRstInd (vmtrace on) - Data page fault in function IAM_F0_lrput. - ATM A5513A ATM_err_1304: VPI/VCI range is invalid. - Lost of ILMI connectivity may be experienced during heavy network and/or NFS traffic over ATM. PHNE_22586: - Can not initialize link with Lucent M770 switch - System panic during boot in alx_complete_conreq - System panics during boot from /sbin/rc2.d/S310atm in getmsg_subr, with message: panic Buffer Overrun. - ifOperStatus (for "Operational Status") and ifAdminStatus (for "Administrative status") are inconsistent for CIP interface. - hatmon prevents ATM package to start as monitored resource while reboot with mc/service cluster. - rstatd hangs on systems that have ATM installed. - After moving a remote LEC from one ATM switch to another ATM switch hp9000 can't ping anymore the remote system. PHNE_21423: - channel error in driver atm2pci panics experienced on V-class servers. - Interoperability problems caused by LANE eavesdropping. - Cannot join Elan services if the LAN type is not specified during the configuration phase. - ATM subsystem start-up failure if no ATM card installed. - Static routes over ATM elan interface fail with error: network unreachable. - High error rate reported by Glance for ELAN interfaces. - Cannot do Token Ring source routing if LECS does not provide Segment ID in the LE_CONFIGURE_RESPONSE. - MAC LEARP entries not deleted or updated. - A patch can be installed on a subsequent release. - HPMC panic when resetting the ATM 622 card. - Data page fault in alx_read_resume when atminit and atmstop are called in a continuous loop. - Data memory protection panic in function LIF_F_handler while doing traffic on Token ring Elan. - Unable to recover a normal traffic on a HA configuration with an elan interface with several ip addresses. The problem occurs when primary elan comes up after both the primary and backup interfaces have been down. - Loopback routes are not created for CIP and LANE interfaces. PHNE_18443: - data page fault panic in function cmPrcTmr. - data page fault panic in function amUsrM02S01. - Cannot start Elan interface configured on an ATM card with a PPA >= 16. - Unable to join Elan services with some connections from Elan services (LES or BUS) blocked in "Go Up" state. - ATM initialization takes long time (up to 10mn) if DNS should be reached through ATM. - Unable to establish ABR SVCs. - Unable to configure with SAM, Elan interface for Elan with an Elan name including character "|". PHNE_17269: - Unable to define two packages on the same elan for High Availability (HA) configurations. - Need to lunch manually the monitor daemon to restore HA on a system. - swverify -v returns errors. - Mib-II counters ifInOctect and IfOutOctects are not updated. - data page fault panic in function cmHashListFind. - data page fault panic in function ecDelMacArp. - data page fault panic in function LCS_F_staind_msap. - Interoperability problems with FORE's DLE services. - Unable to use IP multicast over ATM links. - Unable to get LECS address from network. - Storm of MAC layer broadcast packets on an ELAN. - Bad performances over large ELAN especially when using openview. - Unable to get back primary LEC interface up when the LECS address is got from network especially in HA configuration. - Problem to traffic over an elan interface after it has been switched from token-ring to Ethernet. - Data page fault panic in function cmRmvCbTq. - ATM not operational on card with higher card instance Id number. - Unable to configure or modify ATM configuration on a system with short filename (filename limited to 14 characters) setup. - Performance or data transmission problems with ATM cards J2499A, J2469A and J2468A with the following nettl WARNING logging: [ALXHDM] Aal5 prot encoutered on cid ... PHNE_15346: - problem in ATMHA installation fixed - Cleaning in Lan Emulation Client code about LeArp Response management - Panic during logging in the signaling mux fixed PHNE_14469: - Support of Token Ring Lan Emulation Client - Support of UNI 4.0 - Support of short name file system - Kernel stack overflow problem in signaling fixed - High-Availability switching problem when the primary interface is down - Potential problem for atm diags fixed - potential data corruption fixed PHNE_13599: - support of multicast IP over lan emulation - LEC to LEC incoming connections management improved - memory corruption in stress situations - system hang or panic caused by resources exhaustion - support of 4096 VCs on 622 Mb cards - panic during boot on systems having lots of I/O cards PHNE_12751: - Fix to PHNE_12003 for performances improvement. - Panic or connection loss may occur when several devices share the same interrupt line - Lec not able to join a elan when Lecs address get from the switch and fiber deconnected and then re-connected. - if different elan name is returned from the les the lec may be not able to join the elan. - panic kernel stack overflow possible when performing atminit on some MP systems if both CIP and Lan emul interfaces configured. PHNE_12003: - Fix to improve performances for classical IP and Lan emulation. (Oracle Video Server performance) PHNE_11302: - T600 support PHNE_11301: - LEC drops broadcast packets sent by itself - Memory corruption when using elarp command with more than 20 arp entries. - Kernel stack overflow. - Panic may occur when initializing a lec if the stream server daemon is not running. - Hang or Panic may occur - Too many files opened by ilmid - LE ARP entry not correctly used when LE_ARP_RESPONSE broadcasted - Packet lost by atmloop on PCXL systems. - Connection not correctly closed on NIC when buzy - a LEC cannot be created if ppa greater than 9 - Sometimes, signaling cannot go up after switch failure - Panic if memory missing - Panic when atmstop performed ( MP ) PHNE_10611: - Panic may occur if an LE_ARP_REQUEST is sent by the lec and no response received. This may occur when there is congestion on the network or if the other LEC is not able to send the LE_ARP_RESPONSE PHNE_10151: - error message in SAM/HA when a card instance number greater than 7 is configured (if card instance number > 9 see SR #4701-348425) - Possible data corruption or panic (datapagefault) during lec to lec data transfer - High Availability : Local Recovery Available without MC/Service Guard PHNE_10085: - shutdown causes a fsck at reboot - direct access PVCs cannot be deleted - system panics - DataPageFault in IAM_F0_uwioctl during shutdown -h 0 when stopping ATM (GREhp09445) - DataPageFault in CAM_F_rsrv when atminit/stop during heavy traffic (GREhp09448) - After reboot ARP server may be unable to communicate with its clients (GREhp09603) - FLT B800 when netperf UDP full duplex on elan interface (GREhp08530) - When fiber is unplugged and plugged again, a LEC needs 10 minutes before trying to join the Elan.(GREhp08653) - FLT B800 in IAV_F_handlerwhen using classsical IP interface (GREhp08739) - atmloop man pages missing - netstat -I ipa0 doesn't show output packets - DataPageFault in LVC_F_handler when heavy traffic on 700 series. (GREhp08950) - DataPageFault in EcUiEcmDatReq when atminit loop during traffic (GREhp09604) - signaling stack blocks when connecting to PVC 5 is ignored (GREhp08552) - mode missing in AAL PARAMETERS IE in LEC SETUP messages for UNI 3.0 (GREhp08738) - Interoperability problem with CROSSCOM/XLX switch : ilmid killed during the UNI phase recognition - CONNECT with AAL parameters with NULL max CPCS-SDU size (GREhp08816) - panic in ATQ_F_queue attempt to queue twice (GREhp09029) - The sig_call_ref type is not compliant with signaling. (GREhp09605) - ILMI doesn't work after switch reset (GREhp09620) - DataPageFault(CSV_F_format_dl_discind) when atminit without fibber connected (GREhp08682) - HPMC panic when deconnecting fiber while netperf running on HSC card (GREhp08743) - SVC Go Up and no traffic possible on ARP server after 33h of traffic (GREhp09034) - DataPageFault(CSV_F_format_dl_discind) at boot time (GREhp09047) Defect Description: PHNE_25500: - JAGad56235: Script error while doing an OS update to B.11.11 OEUR-0601. In updating from 10.20 or 11.0 OS Level to B.11.11 OEUR-0601 ic4, the following error was discovered: [20255] Running "preinstall" script for fileset "ATMCORE.ATMCORE-KRN". ps: couldn't get console device alias ps: not enough memory for hash table syncer: a syncer process already exists - JAGab15263: The EPtRf field in atm address has not been described in the atmmgr manpage. Information about the endpoint reference identifier (EPtRf) field, associated with a point-to-multipoint connection on the leaf side in atmmgr command output has not been provided in the 'atmmgr' manpage. - JAGaa03115: Traffic descriptors not taken into account for LanEmul Token-Ring. When some traffic descritors are created to traffic in Token-Ring ELANs, atmconfig command gives no error but they are never taken into account for traffic between ATM token ring ELAN and Token ring network or between two ATM NICs on the Token Ring Elan. - JAGad53408: A5513A card is sometimes not claimed on reboot, on a V2200 system, due to read of the PCI Vendor ID register returning 0xFFFFFFFF. - JAGad65160: The hardware revision of a PCI ATM card needs to be found out without pulling the card out. - JAGad75332: Spinlock deadlock in IAM_F0_lrput() due to a lock not being released. A 10.20 system with ATM product installed along with the patch PHNE_22507 might panic with Spinlock deadlock in IAM_F0_lrput due to ATM code not releasing a lock across a function call. - JAGad90063: "atmconfig show -n" on a non-existent CIP interface causes system to panic. "atmconfig show -n" causes the system to panic if the CIP interface specified correspond to an ATM NIC that does not exist. - JAGad53657: Data page fault in function LVC_F0_remove. LVC_F0_remove could not handle a case where the given LVC_ctx pointer is not in the list and it caused a data page fault triggering a panic. - JAGaa45769 : When Token ring is configured for multicast on LANE v1, it does not work. Token ring configuration for multicast is not supported on LANE v1. - JAGab83144: Data page fault in asAsdRstInd (vmtrace on). During processing of ERROR RECOVERY pdu, asAsdRstInd is called with dlc as parameter but dlc is already freed resulting in the data page fault. - JAGad26995: Data page fault in function IAM_F0_lrput. CIP crashes when processing a message received on one lower read queue because the stream context pointed to by q_ptr has been deallocated. - JAGad71898: ATM A5513A ATM_err_1304: VPI/VCI range is invalid. When replacing obsoleted J3557A ATM card with the new card (A5513A), the system failed to initialise the card, and give the following error : "ATM_err_1304: VPI/VCI range is invalid" - JAGad17083,JAGad77776: Lost of ILMI connectivity may be experienced during heavy network and/or NFS traffic over ATM. On some heavy loaded systems, ILMI is unable to maintain its keep alive mechanism because it is blocked in some system calls especially stat and it is not running in real time priority. Resolution: - JAGad56235: Removed syncer daemon restart from preinstall and preremove scripts of patches. - JAGab15263: The atmmgr manpage has been updated to reflect the information about the EPtRF field. - JAGaa03115: DLSAP-traffic descriptor is modified such that the right traffic descriptor is picked up for Token Ring ELANs. - JAGad53408: The attach routine has been modified to claim the card, even if the read of the Vendor ID register returns 0xFFFFFFFF. - JAGad65160: Code is changed such that the hardware revision of PCI ATM cards is stored in the ift structure. - JAGad75332: Code is changed such that the specified lock is released across the function call thus avoiding the deadlock. - JAGad90063: CIP module is changed such that the PPA is tested to be valid before any MIB operation. - JAGad53657: LVC_F0_remove() code is fixed such that it is able to process properly, even if the given LVC_ctx pointer is not in the list and not cause a panic. - JAGaa45769: The multicast macAddr configuration has been modified based on lanType (802.3/802.5) in LANEv1 code. - JAGab83144: After returning from the SSCOP state machine, dlc is checked such that functions such as asAsdRstInd() will not be called if the dlc is already freed. - JAGad26995: The stream server resets the q_ptr field of both read and write queues when unlinking a stream. - JAGad71898: atminit is modified to read the VPI/VCI bits from the card if an attempt to set the bits fails with EINVAL and retry setting the bits with the read VPI/VCI bits. A warning is printed on stderr to change the configuration through SAM. - JAGad17083,JAGad77776: ILMI now reads the configuration file /etc/atm/ilmid.debug.conf at startup and when SIGHUP is received to see if debug is enabled. PHNE_22586: - JAGad04560: Can not initialize link with Lucent M770 switch MAC address data sent by ILMI is expressed in ASCII rather than HEX. - JAGad21318: System panic during boot in alx_complete_conreq The various error paths in alx_complete_conreq grabs the OPEN_LIST lock before releasing the IFT lock. Since they have both the same order, the kernel panics. - JAGad14719: System panics during boot from /sbin/rc2.d/S310atm in getmsg_subr, with message: panic Buffer Overrun. The driver is reusing the memory block (mblk) carrying a DL_BIND_REQ to reply with a DL_BIND_ACK which does not fit in the buffer. - JAGac79031: ifOperStatus (for "Operational Status") and ifAdminStatus (for "Administrative status") are inconsistent for CIP interface. ifOperStatus and ifAdminStatus objects were not updated properly. - JAGac42555: The MC/SG cluster is configured to automaticaly start with its associated package(s) at system boot up. When the system is rebooted the cluster starts successfully, however the SAP package fails to start , as the associated ATM resource can't be monitored when LANG is not set to "C". - JAGad07300: rstatd hangs on systems that have ATM installed. Control message sent by the rstatd was discarded by the the driver on /dev/atm device. That is why rstatd was blocked in getmsg call. - JAGab77735: After moving a remote LEC from one ATM switch to another ATM switch, the hp9000 can't ping anymore the remote system. This is because its ATM address is not refreshed in the local hp9000 LEC elarp table. According to ATM Forum LANE specifications, the entry should be deleted after the aging timer expired. Resolution: - JAGad04560: Function which encodes the MAC address into the ILMI reply has been corrected. Now ILMI sends 6 binary octets instead of 12 ASCII. - JAGad21318: The IFT lock is released in the error paths of alx_complete_conreq before grabing the OPEN_LIST lock. - JAGad14719: The incoming buffer containing DL_BIND_REQ is freed and a new mblk is allocated to return DL_BIND_ACK. - JAGac79031: Now for CIP, both ifAdminStatus and ifOperStatus are being updated properly. - JAGac42555: This was caused by the mesg witten by atm commands to routed by EMS. The mesg is now written to standard error instead of standard out. - JAGad07300: Now, driver sends a DL_ERROR_ACK (DL_BADPRIM) when receiving an unknown control message namely M_PROTO and M_PCPROTO. - JAGab77735: The new code now passes the right parameters to function that starts LE_ARP aging timer PHNE_21423: - JAGac57113: channel error in driver atm2pci panic on V-class servers. On V-class, driver and card communicate through shared memory managed by the EPIC. If two processors write to the same shared memory location, the order the writes are actually executed is not guaranteed. To guarantee the order a read should be performed between the writes to flush pending reads. In some corner cases, required reads were missing. This leads to channel errors. - JAGab69572: interoperability problems caused by LANE eavesdropping. Some proprietary extensions of LANE do not interoperate with LANE emulation eavesdropping. HP implementation was not providing any support to disable eavesdropping. - JAGab77832: Cannot join LANE services if the LAN type is not specified during the configuration phase. In a few configurations, LANE services may require the LEC to explicitely specify the LAN type to either 802.3/Ethernet or 802.5. HP implementation was not providing users the capacity to configure the LAN type. - JAGab63567: ATM subsystem start-up failure when no ATM card installed. This problem is caused by the fact that the start-up script started some ATM daemons but ATM driver does not let them access some devices if no ATM card is installed. - 5003429381: Static routes over ATM elan interface fail with error: network unreachable. This is caused by the fact that some parameters needed to initialize the interface for IP, should be retrieved from the ELAN services. This may not be completed before the start-up script which add static routes is executed. In this case IP is not aware of the interface. Hence the error network unreachable. - 1653310185, JAGab64432: High error rate reported by Glance for Elan Interfaces. The MIB-II counter ifInErrors was incremented each time a packet was received is a SAP that is not bound with IP. This is case for instance when edge device forward packets broadcasted on SAP 0xFF, or for backup interface on a HA configuration. - 1653308841, JAGab64430: Cannot do Token Ring source routing if LECS does not provide Segment ID in the LE_CONFIGURE_RESPONSE. The LEC stack was not retrieving the Segment from the packet to be able to do source routing. - JAGab77735: MAC LEARP entries not deleted or updated. The problem was caused by incorrect implementation of functions which manage MAC entries. In one case the function which starts aging timer was called with a bad parameter. This was resulting to the timer not being started. - 5003453373, JAGab64953: a patch can be installed on a subsequent release. The product releases the patch applies to where documented but this was not enforced. - JAGab73825: HPMC panic when resetting ATM 622 card. The ATM card continued to do the DMA even after reset of card was received. - JAGad02216: data page fault in alx_read-resume when atmnit and atmstop are called in a continuous loop. The data page fault occurs when alx_read_resume tries to access locks which were already released and freed. - JAGad01352: Data memory protection panic in function LIF_F_handler while doing traffic on Token ring Elan. The RIF length in the source routed packet is odd. The RIF length is used as an offset to calculate a new address. The odd length causes our software to try to access an unsigned short integer on an odd boundary. - JAGad03364: Unable to recover traffic on an HA configuration. This problem is caused by an inconsistency between the behavior of the ATM HA monitor daemon(hatmmon), and IP behavior when several IP addresses are configured over interface. When both the primary and secondary interfaces go down, hatmmon switches the IP addresses over the primary interface. At this time IP requests information (mac address, mtu size, lan type,...) about the interface. As the primary elan interface is down at this time, a null mac address is returned. Later when the primary interface comes up, an ifconfig is performed but IP does not request the parameter and continue to associate a null mac address to the interface. Any traffic with this null mac address is then dropped by the corresponding LEC. - 1653279752, JAGab64354: Loopback routes are not created for CIP and LANE interfaces. Loopback routes were not automatically created for CIP and LANE interfaces. Resolution: - JAGac57113: reads have been added to guarantee order of writes in the shared memory wherever it is necessary. - JAGab69572: LANE eavesdropping can now be disabled if the following is set in the ATM configuration file /etc/rc.config.d/atmconf: ATM_ELAN_NOEAVESDROP=1, before the ATM subsystem is initialized. - JAGab77832: the LAN type can now be specified in the LEC interface configuration file by setting either HP_ATM_ELAN_TYPE=802.3 for 802.3/ethernet HP_ATM_ELAN_TYPE=802.5 for token ring. - JAGab63567: Start-up script has ben changed to check if at least one ATM card is installed before proceeding to card dependant initialization. - 5003429381: Start-up script has been changed to be able to use a configurable parameter to synchronize initialization of Elan interfaces. - 1653310185, JAGab64432: MIB II counter ifInErrors is no longer incremented if a packet is received with a SAP that is not bound with IP. - 1653308841, JAGab64430: The Segment ID is now retrieved from the packets if it is not provided in LE_CONFIGURED_RESPONSE. - JAGab77735: The function which starts aging timer is now called with the right parameter. - 5003453373, JAGab64953: Now when a patch is installed, the version of the product is checked. - JAGab73825: The ATM driver now disables interrupts and disables DMA before resetting the card. - JAGad02116: The ATM driver code now checks the state of VC before attempting to access the lock. - JAGad01352: The standard allows us to drop a packet if the RIF length is odd. Now, the packet is dropped if RIF length is odd. - JAGad03364: hatmmon has been modified to switch over IP addresses only when the interface is UP. - Loopback routes are now automatically created for CIP and LANE interfaces. PHNE_18443: - 5003463679 (JAGaa95697): data page fault panic in function cmPrcTmr. panic+0x14 report_trap_or_int_and_panic+0x80 trap+0xda8 nokgdb+0x8 cmPrcTmr+0x254 ecActvTmr+0x68 LMG_F_actv_timer+0x5c LEC_F0_ursrv+0x38 sq_wrapper+0x94 str_sched_mp_daemon+0x178 str_sched_daemon+0x290 main+0x5bc $vstart+0x48 istackatbase+0x84 The panic is due to the fact that in function cmPrcTmr, a local variable was to used store the pointer to the next timer structure to be processed. That did not take into account the fact that procesing of current timer could lead to free next timer structure. That may result to data page in cmPrcTmr function or a data corruption if the memory bucket is allocated to another structure. -JAGaa52732 : data page fault in function amUsrM02S01 amUsrM02S01+0xb8 amActvConTbl+0x50 AmLiAsdDatInd+0x20e4 AsUiAsdDatInd+0x48 asV3xAa4Sx_y+0x3c asV30AaDatInd+0x50 asV30ProcessSdPdu+0x90 asV30Pdu8S4+0x14 AsLiAalDatInd+0x154 SAA_F0_a_dl_data_ind+0x48 SAA_F_handler+0x36c SIG_F0_lrdata+0x38 SIG_F0_lrput+0xf8 putnext+0x84 CAM_F0_sp_dataind+0x70 streams_put+0x98 CAM_F_data_ind+0x354 fpci_receive_it+0x1500 fpci_isr+0x348 epic_isr+0x58 mp_ext_interrupt+0x1b0 ivti_patch_to_nop3+0x0 idle+0x254 swidle_exit+0x0 The root cause is the data corruption of signaling control block structure caused by the problem reference to Service Request:5003463679. - JAGab15218: Cannot start Elan Interface configured on ATM card with PPA >= 16. The card PPA is coded on both LEC unit and LEC index The mask used to extract card PPA from LEC enabled only 4 bits, truncating PPA >=16. In this case there was an inconsistence between the value extracted from LEC unit and the value extracted from LEC index. That lead to the rejection of the initialization request. - JAGab92756:Unable to join Elan services with some connections from Elan services (LES or BUS) blocked in "Go Up" state. When the Elan service requests a connection with the LEC, the request is routed to an entity that sends an IOCTL to get the vci,vpi. The implementation of the entity was discarding any negative acknowledgement to the IOCTL. That blocked the entity so that it was no longer able to process further requests. - 5003458067: ATM initialization takes long time (up to 10mn) if DNS should be reached through ATM. This is due to the fact that initialization code of ATM was calling DNS functions to validate local IP addresses. DNS was not yet reachable as ATM was not ready. The delay was due to DNS function timeout. - JAGaa94097: Unable to establish ABR SVCs. The ATM stack was checking that ABR Initial Cell Rate negotiated during the SVC establishement was greater than the Minimum Cell Rate. This is not required by standards. -5003359836 (JAGaa02990): Unable to configure with SAM, Elan interface for Elan with an Elan name including character "|". The character "|" was being interpreted by SAM as a pipe command. Resolution: - 5003463679 (JAGaa95697):Change LEC and Signalling timer implementation to avoid access to timer structures already freed. - JAGaa52732: Change LEC and Signalling timer implementation to avoid access to timer structures already freed. - JAGab15218: Set the proper mask to extract correctly the PPA from the LEC index. - JAGab92756: Handle internal error that was leading to the hang of entities that accepts connection from Elan services. - 5003458067: No longer call DNS functions to validate local IP addresses. - JAGaa94097: Remove checking that the negotiated Initial Cell Rate is greater than the Minimum Cell Rate. - 5003359836 (JAGaa02990) Change SAM to no longer interprete "|" as pipe command. PHNE_17269: - 5003388405: Unable to define two packages over the same Elan for a HA configuration. -1653272641 and 1653270694 : Need to manually lunch the monitor daemon to restore HA on a system where the the primary and the secondary ATM card fail. After ATM cards are up again, the administrator have to MANUALLY launch the monitor daemon (serv_hatmmon) to restore HA over ATM. - 5003423764: swverify returns errors: ERROR: File "/usr/sam/lib/kc/subsys.ATM.tx" should have mode "444" but the actual mode is "644". ERROR: File "/usr/sam/lib/kc/subsys.ATM.tx" had a different mtime than expected. ERROR: File "/usr/sam/lib/kc/subsys.ATM.tx" should have size "632" bytes but the actual size is "0" bytes. The cause of the swverify problem is that the patch configure script resets the Kernel Configuration files to empty. The cause of the SAM file becoming empty is that the configure script is not observing the complete list of ATM SAM revision numbers correctly. - 5003431551: mib-II counters ifInOctect and IfOutOctects are not updated. Some mib-II objects where not updated by the LEC. - 5003423194: data page fault panic in function cmHashListFind panic+0x10 report_trap_or_int_and_panic+0xe8 trap+0xa48 $call_trap+0x20 cmHashListFind+0xd4 ecAllocSuInstId+0x68 ecElanConReq+0x64 ecELE0S0+0xe4 EcMiLecCntrlReq+0x1e4 LCS_F_ctrl_msap+0x5c ELA_F0_config+0x80 ELA_F0_starting+0x6c ELA_F_handler+0x580 LVC_F0_a_srv_trap_port+0x7c LVC_F_handler+0x1038 LEC_F0_lrproto+0x174 LEC_F0_lrput+0x9c putnext+0x74 DLS_F_sp_send+0x5c streams_put+0xe0 TRP_F0_trapctx_send+0x1f4 TRP_F_traplist_send+0x58 NIC_F0_a_settingup_isup+0x24 NIC_F_handler+0x98 NIC_F0_sp_ifstate+0x124 MON_F_enqueue_mblk+0x94 CAM_F_wput+0x600 putnext+0x74 SIG_F0_lwsrv+0x44 sq_wrapper+0xb8 str_sched_mp_daemon+0x284 str_sched_daemon+0x1f4 main+0x944 $vstart+0x34 $locore+0x74 main+0x944 $vstart+0x34 $locore+0x74 This problem occurs when the customer reboots the switch because when such operation is performed the carrier state change several hundred thousands times in 2 or 3 seconds and the physical driver in J2805. - 5003401950: Interoperability problems with FORE's DLE. Fore DLE services uses anycast address to join LES. ATM Stack was only supporting unicast address for UNI 3.0 and UNI 3.1. - 5003359661: use IP multicast over ATM links. IP Multicast packets are mapped to mac multicast on link layer level. Such packets were filtered by the LEC interface. so that it was not able to operate any protocol using IP multicast over ATM (ex. IGMP). - 1653271346: storms of mac layer brodcast packets. If two IP subnet are configured over the same ELAN, HP system forward broadcast packets of the IP subnet it is not attached. This may lead to storms of brodcast packets. - 1653282145: Bad performances over large ELAN This happens when HP system traffic with a lot End systems especially when using openview. The LE_ARP table contains a lot of entries. The processing of timers associated to these timers consume a lot cpu on the expense of data transfer. - 5003447136: Problem to get back primary LEC interface up when LECS address is got from network. This occurs especially when using cisco dual homing configuration for HA. The cause is a synchronization problem between ILMI and LEC that prevent LEC from trying to join the ELAN services. - 5003447029: data page fault panic in function ecDelMacArp panic+0x3c report_trap_or_int_and_panic+0xe8 trap+0x1058 $call_trap+0x20 ecDelMacArp+0x24 ecRelOldMacArp+0x80 EcUiEcmDatReq+0x504 LIF_F_send_msg+0xc4 csq_turnover+0x8c str_sched_up_daemon+0x1b8 str_sched_daemon+0xf4 main+0x94c $vstart+0x34 $locore+0x74 The panic is due to the fact that a memory allocation was not handled properly. - 5003447011: data page fault panic in function LCS_F_staind_msap report_trap_or_int_and_panic+0xe8 interrupt+0x458 $ihndlr_rtn LCS_F_staind_msap+0x178 PtMiLecStaInd+0x1c EcMiLecStaInd+0x24 ecGenReport+0xa8 ecMAE0S1+0x330 ecELE18Sa+0x1d4 ecElanDatInd+0x260 EcLiAalDatInd+0x2c0 LVC_F_handler+0x3fc LEC_F0_lrput+0xe4 putnext+0x74 CAM_F0_sp_dataind_mp+0x94 streams_put+0xe0 CAM_F_data_ind+0x2e4 atmgsc_recv+0xe5c The panic is due to the fact that a memory allocation was not handled properly. - JAGaa46673: Problem to traffic over an elan interface after it was switched from token-ring to Ethernet. This occurs if an elan interface previously configured for a token-ring elan is modified to join an ethernet elan. The interface keep sending tokeng-ring packet format. - JAGaa51478: Data page fault panic in function cmRmvCbTq. report_trap_or_int_and_panic+0xe8 interrupt+0x458 $ihndlr_rtn+0x0 cmRmvCbTq+0x58 amStopNtcTmr+0x78 AmLiAsdConCfm+0x4fc AsUiAsdConCfm+0x3c asAsdConCfm+0x40 asV31Aa1S2_2+0x24 asV31AaEstCfm+0x44 asV31ConCS2+0x90 asV31Pdu1S2+0x5c AsLiAalDatInd+0x11c SAA_F0_a_dl_data_ind+0x40 SAA_F_handler+0x430 SIG_F0_lrdata+0x30 SIG_F0_lrput+0xe8 putnext+0x74 CAM_F0_sp_dataind+0x5c streams_put+0xe0 CAM_F_data_ind+0x154 alx_receive_it+0x570 alx_isr+0x11c wsio_interrupt+0x4c mp_ext_interrupt+0x2a0 $RDB_int_patch+0x58 idle+0x9f4 swidle_exit+0x0 - JAGaa45619: ATM not operational on card with higher card Instance Id. The ATM software was expecting the card instance Id to be less than 16. But on some platforms with a lot of slots, the card instance Id of an ATM card can be greater than 16. - JAGaa03065: Unable to configure or modify configuration of ATM on system with short filename (less than 14 characters). This might occur on system where PVCs are traffic descriptors are cofigured for a CIP or LANE interface. The root cause is that filename of some temporary files used as locks for synchronyzing ATM configuration, when truncated to 14 characters, conflict with the name of configuration files used to save PVCs or traffic descriptors parameters. - 5003451872:ATM with the J2499A Hardware silently discard packets. This results to performance or data transmission problems with ATM cards J2499A, J2469A and J2468A with the following nettl WARNING logging: [ALXHDM] Aal5 prot encoutered on cid ... Resolution: - 5003388405: Added EMS support for High Availability (EMS HA-ATM) especially to be able to define two packages on the same elan. - 1653272641,1653270694: Added EMS support for High Availability (EMS HA-ATM) especially to not have to launch manually the monitor daemon to recover HA functionnality over ATM. - 5003423764: Update ATM subsystem definition file /usr/sam/lib/kc/subsys.ATM.tx properly. - 5003431551: Implement all mib-II counters supported by HP. - 5003423194: wait until carrier is stable before notifying to ATM stack change in operational status. - 5003401950: No longer restrict calling ATM address to unicast. - 5003359661: Change LEC implementation to be able to enable reception of multicast packets. - 5003359661: Notify IP if a packet is a link level brodcast to avoid forwarding of such packets. - 1653282145:Optimize handling of LE_ARP entry timers to consume less on the expense of data transfer. - 5003447136: Change ILMI to not block LEC the process of joining elan services. - 5003447029: take into account properly memory allocation failure. - 5003447011: take into account properly memory allocation failure - JAGaa46673: clean up ELAN interface structures after switching from token-ring to Ethernet. - JAGaa51478: data page fault panic in function cmRmvCbTq. Pass correct parameter to the function. - JAGaa45619: Increase the maximum value expected for CArd Instance Id to 31. - JAGaa030651: Change the name of lock files to avoid conflict with configuration files when truncated to 14 characters. - 5003451872: no longer discard packets with CPCS-UU or CPI fields in AAL-5 trailer not set to 0. PHNE_15346: - 1653262592 and JAGaa08151 : Panic in the signaling mux when logging a message. This occurs when some specific troubles are experienced in the atm conf. panic+0x10 report_trap_or_int_and_panic+0xe8 trap+0xf88 $RDB_trap_patch+0x20 strlen+0xc ALT_F_Log+0x288 SSV_F0_log_cnevt+0x70 SSV_F_handler+0x76c SMG_F_call_services_handler+0x7c PtUiAmtStaInd+0x4c AmUiAmtStaInd+0x44 AmUiAmtRstReq+0x42c SSV_F0_generate_restart+0xac SSV_F_handler+0x650 SIG_F0_lrproto+0x58c SIG_F0_lrsrv+0xbc sq_wrapper+0xb8 - JAGaa06532 and JAGaa08068 : routing through a CIP interface does not work - JAGaa06022 : spare fields in LE_ARP_xx are no more checked - 5003416495 and JAGaa06531 : Unsollicited LE_ARP_RESPONSE are no more used. - JAGaa08113 : When installing a patch including ATMHA the HA configuration were no more seen by SAM. PHNE_14469: - GREhp11758: potential data corruption - GREhp11910: When using HA configuation, the pmtu size for the secondary interface may remain to 0 when the primary interface is down when the HA monitor is started. - GREhp11485: No file of the atm bundle has now a name exceeding 14 characters - GREhp11116: Kernel Stack overflow in Signaling fixed panic+0x10 report_trap_or_int_and_panic+0xe8 trap+0x1058 $call_trap+0x20 SGetMsg+0x0 amBldMsg+0x38 amGenPdu+0x5c amGenRelCmplt+0xdc AmLiAsdDatInd+0xd5c AsUiAsdDatInd+0x28 asV3xAa4Sx_y+0x3c asV31AaDatInd+0x74 asV31Pdu8S10+0xd4 AsLiAalDatInd+0x114 - 1653248930: Bad lec name generated by SAM when X25 in the same system. ( named el100 instead of ela100 ). PHNE_13599: - GREhp11024: Now an incoming lec to lec setup is not rejected if no connection control bloc exists, even is the src atm address is lower than the local one - GREhp10849: udp_netperf full duplex CIP - GREhp10537: Systeme I/O resources exhaustion with very small packet traffic - GREhp10685: Memory corruption in stress situations, causing panic or hang - GREhp10842: GSC bus heavy use, may cause other I/O cards to fail, causing panic - GREhp10898: Rare instances of panic when ATM interface is stopped - GREhp11118: Rare instances of panic in case of low memory situations - GREhp11335: Panic during boot on systems having lots of I/O cards, caused by bad detection of shared interrupt level stack trace for event 0 crash event was a panic panic+0x10 report_trap_or_int_and_panic+0xe8 interrupt+0x458 $ihndlr_rtn+0x0 alx_isr+0x1a8 wsio_interrupt+0x4c pa_shared_interrupt+0x34 mp_ext_interrupt+0x2a0 $RDB_int_patch+0x58 idle+0x754 swidle_exit+0x0 - GREhp11224: Support of 4096 VCs on 622 Mb cards - GREhp10684: Incorrect output of "atmmgr show -t" PHNE_12751: - GREhp11065: panic kernel stack overflow when atminit performed - GREhp10711: panic in vctab management report_trap_or_int_and_panic trap+0xe8c $RDB_trap_patch+0x20 spinlock_patched_to_nop+0x20 VCC_F0_vcctx_lock+0x10 VCC_F_vctab_find_vpci+0x98 NIC_F_nicctx_getobj+0x8c NIC_F_nicctx_getnext+0x158 CAM_F0_ioctl_handler+0x4ac CAM_F_wput+0x554 putnext+0x50 - GREhp10853: panic in IAV_F_handler panic+0x10 report_trap_or_int_and_panic+0xe8 trap+0xf88 $RDB_trap_patch+0x20 ASS_F_handler+0xd84 IAV_F0_a_free_stream+0xf0 IAV_F_handler+0x520 IAM_F0_lrproto+0xb8 IAM_F0_lrput+0x134 putnext+0x74 CAM_F_rsrv+0x48 sq_wrapper+0x8c str_sched_up_daemon+0x184 str_sched_daemon+0xf4 main+0x944 - GREhp10796 messages logged: [GSCHDM] Incoherence between mailboxes and transmit buffers. [GSCHDM] Timing inversion. - GREhp10667 : SDUs to big errors occurs - GREhp10668 : data page fault on T600 or K370/K570 when several devices share the same interrupt line panic+0x14 report_trap_or_int_and_panic+0x4c interrupt+0x100 $ihndlr_rtn+0x0 allocb+0x210 atmgsc_get_str+0x54 atmgsc_recv+0x4f4 atmgsc_idma_streambuf_comp+0x18 atmgsc_isr+0x128 wsio_interrupt+0x50 pa_shared_interrupt+0x30 mp_ext_interrupt+0x10c ivti_patch_to_nop3+0x0 PHNE_12003: - GREhp10677: Enhancement to improve performances PHNE_11302: - T600 support PHNE_11301: - GREhp10570: LEC drops broadcast packets sent by itself (SR #5003-376905) - GREhp10559: Memory corruption when using elarp command with more than 20 arp entries. - GREhp10549: Kernel stack overflow, below are 2 examples of kernel stacks: report_trap_or_int_and_panic+0x8c trap+0x10b8 $RDB_trap_patch+0x20 amEncU8+0x4 amEncElmts+0x304 amEncPdu+0x18 amBldMsg+0x9c amGenPdu+0x5c amGenRelCmplt+0xdc amComM4DSND+0x20c amActvConTbl+0x44 AmLiAsdDatInd+0xe4c AsUiAsdDatInd+0x34 asV3xAa4Sx_y+0x3c asV30AaDatInd+0x4c asV30ProcessSdPdu+0x88 asV30Pdu8S4+0x10 AsLiAalDatInd+0x120 SAA_F0_a_dl_data_ind+0x50 SAA_F_handler+0x3f0 SIG_F0_lrdata+0x30 SIG_F0_lrsrv+0xd4 sq_wrapper+0xb8 csq_turnover+0x8c putnext+0xb8 CAM_F_read_put+0x44 streams_put+0xe4 DLS_F0_ics_putq+0x44 DLS_F_send+0x1c NIC_F_nicctx_handler+0x1298 SVC_F0_vcctx_handler+0x4e8 VCC_F_vcctx_handler+0x74 SVC_F0_aconreq+0x2c4 SVC_F0_vcctx_handler+0xb28 VCC_F_vcctx_handler+0x74 NIC_F_nicctx_handler+0x155c DLS_F0_aconreq+0xc8 DLS_F_strctx_handler+0x57c CAM_F_wput+0x3d0 putnext+0x74 putmsg_subr+0x744 putmsg+0x844 syscall+0x1a8 report_trap_or_int_and_panic+0x8c trap+0x1038 $call_trap+0x20 amGenRelCmplt+0x44 amComP03SND+0x120 amActvConTbl+0x44 AmUiAmtRelReq+0x25c SSV_F0_amuiamtrelrq+0xb8 SSV_F_handler+0x914 SMG_F_call_services_handler+0x7c PtUiAmtConInd+0x30 AmUiAmtConInd+0x38 amUsrM05S00+0x1c4 amActvConTbl+0x44 AmLiAsdDatInd+0xe4c AsUiAsdDatInd+0x34 asV3xAa4Sx_y+0x3c asV30AaDatInd+0x4c asV30ProcessSdPdu+0x88 asV30Pdu8S4+0x10 AsLiAalDatInd+0x120 SAA_F0_a_dl_data_ind+0x50 SAA_F_handler+0x444 SIG_F0_lrdata+0x30 SIG_F0_lrsrv+0xd4 sq_wrapper+0xb8 str_sched_up_daemon+0x2e0 str_sched_daemon+0xf4 main+0x334 - GREhp10523 : Panic when memory missing in Caam report_trap_or_int_and_panic+0x8c trap+0xbec $call_trap+0x20 DLS_F0_fmt_ok_ack+0x0 DLS_F0_adisconreqack+0x74 DLS_F_strctx_handler+0x61c PVC_F0_vcctx_handler+0xb30 VCC_F_bufcall_handler+0x90 ABC_F0_bufcall_handle+0x44 csq_protect+0x15c bufcall_rsrv+0xcc str_mem_daemon+0x140 main+0x348 $vstart+0x34 - GREhp10538 : Panic in LEC when atmstop performed ( MP only) report_trap_or_int_and_panic+0x8c trap+0xc18 $call_trap+0x20 LIF_F_ifOutput+0x28 ip_output+0x7ec tcp_output+0x2dc tcp_usrreq+0x608 soconnect+0x90 connect+0xc8 syscall+0x1a8 - GREhp10524 : Panic in LEC when atmstop performed report_trap_or_int_and_panic+0xe8 trap+0xf88 $call_trap+0x20 ELA_F_handler+0x1c ELA_F0_delete_mybackup+0x24 ELA_F_handler+0x3b4 LVC_F0_a_srv_trap_port+0x58 LVC_F_handler+0xf34 LEC_F0_lrproto+0x14c LEC_F0_lrput+0x9c putnext+0x74 CAM_F_read_put+0x44 streams_put+0xe0 - GREhp10452: Hang when opening connection on non coherent-io systems such as B132. A hpmc may occur instead of hang. - GREhp10124: Panic in LEC if stream server daemon not started panic+0x10 report_trap_or_int_and_panic+0xe8 trap+0xf88 $call_trap+0x20 EcMiLecStsReq+0x4c LCS_F_sts_msap+0x64 LMG_F0_Get_lecStatisticsEntry+0x34 LMG_F0_get+0x9c LMG_F_ioctl_mgmt+0x94 LEC_F0_uwioctl+0xcc LEC_F0_uwput+0x9c putnext+0x74 - GREhp10337: Mailbox full The followin error message may be displayed and ATM traffic hangs [GSCHDM] Mailbox 4 full Unknown Action Message: Report the problem to your HP representative. - GREhp10308: Panic (data pagefault) panic+0x14 report_trap_or_int_and_panic+0x4c interrupt+0x100 $ihndlr_rtn+0x0 atmgsc_recv+0x424 atmgsc_idma_streambuf_comp+0x18 atmgsc_isr+0xfc wsio_interrupt+0x50 inttr_emulate_save_fpu+0xf0 ecMacArpTmrExpiry+0x18c cmPrcTmr+0xec ecActvTmr+0x5c LMG_F_actv_timer+0x70 LEC_F0_ursrv+0x30 sq_wrapper+0x88 - GREhp09792: HPMC (Bus Timeout error or invalid PDIR entry) or system hang - GREhp10304: The number of files opened by ilmid may be very big. - GREhp08364: On PCXL systems, atmloop may loss some packets - GREhp09442: When closing a connection, it may be not completely closed in the nic and one connection is lost. - GREhp10125: After signaling failure at the network part, the signaling is not able to go up at the user part - GREhp09802: It is not possible to create a LEC if the card instance number is greater than 9. - GREhp10296: if a LE_ARP_RESPONSE is received for the broadcast mac address, an new entry is created and this entry may disturb LEC behavior. - GREhp10338: Data page fault (isr.ior = 0.28) in ecELE19S11 - GREhp10295: If a LE_ARP_RESPONSE without sending the LE_ARP_REQUEST, the new entry may be unusable and traffic impossible to the associated LEC. - GREhp09920: Panic when memory missing panic+0x14 report_trap_or_int_and_panic+0x4c trap+0xe50 $RDB_trap_patch+0x20 SSS_F_SFndLenMsg+0x0 SFndLenMsg+0x2c EcLiAalDatInd+0x120 LVC_F_handler+0x458 LEC_F0_lrput+0xe4 putnext+0x1ac PHNE_10611: - GREhp09736: Panic if No LE_ARP_RESPONSE received panic+0x14 ecELE19S11+0x110 ecElanDatInd+0x310 EcLiAalDatInd+0x1d4 PHNE_10151: - an ATM card with a card instance number greater than 7 cannot be managed (if card instance number > 9 see SR #4701-348425) - Panic (DataPageFault) in LSS_F_SAddPstMsgMult or memory corruption (GREhp09825) panic+0x10 report_trap_or_int_and_panic+0xe8 trap+0xf88 $RDB_trap_patch+0x20 LSS_F_SAddPstMsgMult+0x1ec SAddPstMsgMult+0x1c EcUiEcmDatReq+0xb0 LIF_F_send_msg+0x5c streams_put+0xe0 LIF_F0_send_fragment+0x168 LIF_F0_send_datareq+0x24 LIF_F_acOutput+0x20 unicast_ippkt+0xe0 arp_resolve+0xf4 LIF_F_ifOutput+0x3c PHNE_10085: 1653-011061 shutdown causes a fsck at reboot 4701-346882 direct access PVCs cannot be deleted - panic in ecInitAmCgPtyNmb function - panic in ecTxCtrlFrame function - GREhp09445 DataPageFault during shutdown -h 0 when stopping ATM panic+0x10 report_trap_or_int_and_panic+0xe8 trap+0xf88 $RDB_trap_patch+0x20 IAM_F0_uwioctl+0x30 IAM_F0_uwput+0x94 puthere+0xe4 osr_unlink_subr+0x190 osr_close_subr+0x2c0 hpstreams_close_int+0x2d0 hpstreams_close+0x24 - GREhp09448 DataPageFault when atminit/stop during heavy traffic panic+0x10 report_trap_or_int_and_panic+0xe8 trap+0xf88 $RDB_trap_patch+0x20 sth_rput+0x58 putnext+0x74 CAM_F_rsrv+0x44 sq_wrapper+0xb8 str_sched_mp_daemon+0x114 str_sched_daemon+0x1f4 - GREhp09603 After reboot ARP server may be unable to communicate with its clients. This occurs when the ARP server has a bad ATM address for itself in the classical ip Arp table. ( When the client sends an Arp Request for the Arp server IP address, the ARP Reply does not contain any valid ATM address for this IP address - GREhp08530 FLT B800 when netperf UDP full duplex on elan interface - GREhp08653 When the fiber is unplugged and plugged again, a LEC needs 10 minutes before trying to join the Elan. - GREhp08739 FLT B800 when using classsical IP interface. panic+0x10 report_trap_or_int_and_panic+0xe8 trap+0xf88 $call_trap+0x20 IAV_F_handler+0x5e0 IAM_F0_lrproto+0x148 IAM_F0_lrput+0x134 putnext+0x74 CAM_F_rsrv+0x44 sq_wrapper+0xb8 str_sched_mp_daemon+0x284 str_sched_daemon+0x1f4 - GREhp08800 man pages for atmloop are not installed - GREhp08840 netstat -I ipa0 doesn't show output packets - GREhp08950 DataPageFault when heavy traffic on 700 series. panic+0x10 report_trap_or_int_and_panic+0xe8 trap+0xf88 $call_trap+0x20 putnext+0x5c LVC_F_handler+0x424 PtLiAalDatReq+0x2c EcLiAalDatReq+0x40 ecElanDatReq+0xa4 ecAAE4S4+0x28 ecMAE2S3+0x54 EcUiEcmDatReq+0x26c LIF_F_send_msg+0x4c - GREhp09028 DataPageFault during Elan netperf UDP full duplex panic+0x10 report_trap_or_int_and_panic+0xe8 trap+0xf88 $call_trap+0x20 DLS_F0_fmt_ok_ack+0x0 DLS_F0_adisconreqack+0x74 DLS_F_strctx_handler+0x61c PVC_F0_vcctx_handler+0xb30 VCC_F_bufcall_handler+0x90 ABC_F0_bufcall_handle+0x44 csq_protect+0x154 bufcall_rsrv+0xbc - GREhp09604 DataPageFault when atminit loop during traffic panic+0x10 report_trap_or_int_and_panic+0xe8 trap+0xf88 $RDB_trap_patch+0x20 EcUiEcmDatReq+0x2c LIF_F_send_msg+0x4c csq_turnover+0x8c str_sched_mp_daemon+0x164 str_sched_daemon+0x1f4 - GREhp08552 signaling stack blocks when connecting to PVC 5 is ignored: when for some reason signaling stack request connection to PVC 5 and this request is ignored i.e the request is neither rejects nor confirmed,for the corresponding link, signaling dlsap is blocked in state connecting. So subsequents connection requests generated at expiry of timer TCON are ignored. This make that SVCs can no longer be set up on this link even after atminit. The only way to have again SVCs is to reboot. - GREhp08738 LAN Emulation specs require that for UNI 3.0 the mode must be present in AAL PARAMETERS IE in SETUP message. This element is missing in SETUP messages initiated by LEC. This prevents to connect to some equipments. - GREhp08793 Interoperability problem with CROSSCOM/XLX switch : ilmid killed during the UNI phase recognition. After atminit, atmmgr shows that the ILMI address registration is not complete. Indeed, about 10 seconds after atminit, ilmid does a coredump. Trace shows that the switch sent us two large packets filled with SNMP requests. As these are the last packets of the trace, ILMI does not support some of the requested objects, causing a core. - GREhp08816 CONNECT with AAL parameters with NULL max CPCS-SDU size: some interoperability problems were encountered due to the fact that ATM stack acknoweledge some incoming SETUP messages destined to LEC with CONNECT messages that have AAL parameters withunexpected null maximum cpcs-ssdu size. - GREhp09029 panic in ATQ_F_queue attempt to queue twice panic+0x10 ATQ_F_queue+0x70 ABC_F_bufcall+0x1c PVC_F0_acommit+0x1f0 PVC_F0_vcctx_handler+0x354 VCC_F_vcctx_handler+0x28 VCC_F_vctab_start+0xc0 NIC_F_nicctx_handler+0x7d8 CAM_F_if_state+0x60 msgbuf shows: panic: (display==0xbf00, flags==0x0) ATQ_F_queue attempt to queue twice - GREhp09605 The sig_call_ref type is not compliant with signaling. After having opened 65535 connections, no more connections can be opened. - GREhp09620 ILMI doesn't work after switch reset - GREhp08682 DataPageFault(CSV_F_format_dl_discind) when atminit without fibber connected panic+0x10 report_trap_or_int_and_panic+0xe8 trap+0xf88 $call_trap+0x20 CSV_F_format_dl_discind+0x8 PVC_F0_vcctx_handler+0x5d0 VCC_F_vcctx_handler+0x28 DLS_F_connect_resp+0x94 csq_turnover+0x8c - GREhp08743 HPMC panic when deconnecting fiber while netperf running on HSC card. The problem occurs only when the card in the "Turbo slot" of the 9000/D350 is started. The HPMC occurs because a parity error has been seen on the GSC+ bus during a read command started by atmgsc_recv(). The analysis of the PIM show the following: For the bus converter (path 10/63) 0x35/se ==> The IOA LBC saw a parity error on GSC+. For the ATM card in the "Turbo slot" (path 10/12) 0x34/fe ==> ErrorL seen while returning data on DIO read - GREhp09034 SVC Go Up and no traffic possible on ARP server after 33h of traffic, the output of 'atmmgr 0 show -v' command shows a lot of VCs with status 'Go Up'. - GREhp09047 DataPageFault(CSV_F_format_dl_discind) at boot time panic+0x10 report_trap_or_int_and_panic+0x8c trap+0xbf0 $call_trap+0x20 CSV_F_format_dl_discind+0x0 PVC_F0_vcctx_handler+0x5d8 VCC_F_vcctx_handler+0x28 DLS_F_connect_resp+0x94 csq_turnover+0x8c SR: 5003388405 5003423764 5003431551 5003423194 5003401950 5003359661 1653270694 1653272641 1653271346 5003437756 1653282145 5003447136 5003447029 5003447011 5003370155 5003370163 5003371898 5003369702 5003371179 4701348425 1653011061 4701346882 5003376905 5003388132 5003386862 5003382069 1653235788 1653235309 1653246223 1653249342 1653248930 1653262592 5003416495 5003451872 5003458067 5003359836 5003463679 5003429381 1653310185 1653308841 5003453373 1653279752 8606187025 8606184199 8606195956 8606206157 8606220927 8606184449 8606110441 8606157664 8606202724 8606147741 8606208589 4700102764 8606103177 8606107499 8606107574 8606125676 8606126548 8606128231 8606132203 8606132968 8606134224 8606135426 8606138099 8606140027 8606145383 8606146378 8606147517 8606151979 8606152147 8606157776 8606157967 8606158088 Patch Files: /usr/conf/lib/libatmgsc.a /usr/conf/lib/atmgsc_dbg.o /usr/conf/master.d/atmgsc /usr/conf/lib/libatm2gsc.a /usr/conf/lib/atm2gsc_dbg.o /usr/conf/master.d/atm2gsc /usr/sbin/alxdump /usr/conf/lib/libatmnio.a /usr/conf/lib/atmnio_dbg.o /usr/conf/master.d/atmnio /usr/conf/lib/libatm2pci.a /usr/conf/lib/atm2pci_dbg.o /usr/conf/master.d/atm2pci /usr/conf/lib/libatm.a /usr/conf/lib/atm_dbg.o /usr/conf/master.d/atm /usr/sbin/atminit /usr/sbin/atmstop /usr/sbin/atminit_net /usr/sbin/atmstop_net /usr/sbin/atmtune /usr/sbin/atmmgr /usr/sbin/atmconfig /usr/sbin/elstat /usr/sbin/elarp /usr/lib/nls/msg/C/atminit.cat /usr/lib/nls/msg/C/atmmgr.cat /usr/lib/nls/msg/C/atmconfig.cat /usr/lib/nls/msg/C/elarp.cat /usr/lib/nls/msg/C/elstat.cat /usr/lib/nls/msg/C/atmloop.cat /usr/lib/nls/msg/C/atmcheck.cat /usr/lib/nls/msg/C/atmserver.cat /usr/lib/nls/msg/C/atm.cat /usr/newconfig/etc/rc.config.d/atmconf /sbin/init.d/atm /usr/sbin/atmstrsrvd /usr/lib/libatmfmt.sl /usr/sbin/atmdebug /usr/sbin/atmloop /usr/sbin/atmcheck /usr/lbin/atmserver /usr/lbin/ilmid /usr/newconfig/etc/atm/ilmid.conf /etc/atmrev/atm2to3 /etc/atmrev/atm3to4 /etc/atmrev/atm4to5 /usr/contrib/bin/atminfo /usr/share/man/man1m.Z/atmcheck.1m /usr/share/man/man1m.Z/atmserver.1m /usr/share/man/man1m.Z/atminit.1m /usr/share/man/man1m.Z/atminit_net.1m /usr/share/man/man1m.Z/atmmgr.1m /usr/share/man/man1m.Z/atmloop.1m /usr/share/man/man1m.Z/atmstop.1m /usr/share/man/man1m.Z/atmstop_net.1m /usr/share/man/man1m.Z/atmconfig.1m /usr/share/man/man1m.Z/elarp.1m /usr/share/man/man1m.Z/elstat.1m /opt/hatmmon/lib/libgendico.sl /opt/hatmmon/lib/libgenreply.sl /opt/hatmmon/lib/libhaconfig.sl /opt/hatmmon/sbin/hatmmon /opt/hatmmon/sbin/serv_hatmmon /opt/hatmmon/sbin/hatmmigrate /opt/hatmmon/lib/libatmconfig.sl /opt/hatmmon/lib/libatmsts.sl /opt/hatmmon/lib/libatmstse.sl /opt/hatmmon/lib/libgenutil.sl /opt/hatmmon/lib/libgenutile.sl /opt/hatmmon/lib/libshaconfig.sl /opt/hatmmon/lib/libipaddr.sl /opt/hatmmon/lib/libsamcfg.sl /opt/hatmmon/lib/libatmcmds.sl /opt/hatmmon/lib/nls/msg/C/hatmmon.cat /opt/hatmmon/lib/nls/msg/C/hatmmone.cat /opt/hatmmon/share/man/man1m.Z/hatmmon.1m /opt/hatmmon/share/man/man1m.Z/serv_hatmmon.1m /usr/sam/lbin/atm.sh /usr/sam/lbin/atmupdate.sh /usr/sam/lib/kc/subsys.ATM.tx /usr/sam/lib/kc/params.ATM.tx /usr/sam/lib/kc/drivers.ATM.tx /usr/sam/lib/C/atmnia.ui /usr/sam/lib/C/atminuse.ui /usr/sam/lib/atm/atm.tm /usr/sam/lib/atm/atm.da /usr/sam/lib/atm/libatm.sl /usr/sam/help/C/atm/ATM.hv /usr/sam/help/C/atm/ATM.hvk /usr/sam/help/C/atm/ATM.xrh /usr/sam/help/C/atm/ATM00.ht /usr/sam/help/C/atm/ATM01.ht /usr/sam/help/C/atm/ATM02.ht what(1) Output: /usr/conf/lib/libatmgsc.a: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /usr/conf/lib/atmgsc_dbg.o: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /usr/conf/master.d/atmgsc: None /usr/conf/lib/libatm2gsc.a: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /usr/conf/lib/atm2gsc_dbg.o: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /usr/conf/master.d/atm2gsc: None /usr/sbin/alxdump: None /usr/conf/lib/libatmnio.a: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /usr/conf/lib/atmnio_dbg.o: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /usr/conf/master.d/atmnio: None /usr/conf/lib/libatm2pci.a: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /usr/conf/lib/atm2pci_dbg.o: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /usr/conf/master.d/atm2pci: None /usr/conf/lib/libatm.a: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) ATMSAM_5 /usr/conf/lib/atm_dbg.o: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /usr/conf/master.d/atm: None /usr/sbin/atminit: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) ATMSAM_5 ATMSAM_5 /usr/sbin/atmstop: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) ATMSAM_5 ATMSAM_5 /usr/sbin/atminit_net: ATMSAM_5 ATMSAM_5 /usr/sbin/atmstop_net: ATMSAM_5 ATMSAM_5 /usr/sbin/atmtune: None /usr/sbin/atmmgr: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) ATMSAM_5 /usr/sbin/atmconfig: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) ATMSAM_5 /usr/sbin/elstat: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /usr/sbin/elarp: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /usr/lib/nls/msg/C/atminit.cat: None /usr/lib/nls/msg/C/atmmgr.cat: None /usr/lib/nls/msg/C/atmconfig.cat: None /usr/lib/nls/msg/C/elarp.cat: None /usr/lib/nls/msg/C/elstat.cat: None /usr/lib/nls/msg/C/atmloop.cat: None /usr/lib/nls/msg/C/atmcheck.cat: None /usr/lib/nls/msg/C/atmserver.cat: None /usr/lib/nls/msg/C/atm.cat: None /usr/newconfig/etc/rc.config.d/atmconf: None /sbin/init.d/atm: None /usr/sbin/atmstrsrvd: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) queue primitives (ATQ) $Revision: 6.1 $ /usr/lib/libatmfmt.sl: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /usr/sbin/atmdebug: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /usr/sbin/atmloop: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /usr/sbin/atmcheck: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /usr/lbin/atmserver: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /usr/lbin/ilmid: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /usr/newconfig/etc/atm/ilmid.conf: None /etc/atmrev/atm2to3: ATMSAM_3 ATMSAM_3 /etc/atmrev/atm3to4: None /etc/atmrev/atm4to5: None /usr/contrib/bin/atminfo: None /usr/share/man/man1m.Z/atmcheck.1m: None /usr/share/man/man1m.Z/atmserver.1m: None /usr/share/man/man1m.Z/atminit.1m: None /usr/share/man/man1m.Z/atminit_net.1m: None /usr/share/man/man1m.Z/atmmgr.1m: None /usr/share/man/man1m.Z/atmloop.1m: None /usr/share/man/man1m.Z/atmstop.1m: None /usr/share/man/man1m.Z/atmstop_net.1m: None /usr/share/man/man1m.Z/atmconfig.1m: None /usr/share/man/man1m.Z/elarp.1m: None /usr/share/man/man1m.Z/elstat.1m: None /opt/hatmmon/lib/libgendico.sl: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /opt/hatmmon/lib/libgenreply.sl: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /opt/hatmmon/lib/libhaconfig.sl: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /opt/hatmmon/sbin/hatmmon: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /opt/hatmmon/sbin/serv_hatmmon: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /opt/hatmmon/sbin/hatmmigrate: None /opt/hatmmon/lib/libatmconfig.sl: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /opt/hatmmon/lib/libatmsts.sl: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /opt/hatmmon/lib/libatmstse.sl: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /opt/hatmmon/lib/libgenutil.sl: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /opt/hatmmon/lib/libgenutile.sl: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /opt/hatmmon/lib/libshaconfig.sl: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /opt/hatmmon/lib/libipaddr.sl: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /opt/hatmmon/lib/libsamcfg.sl: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /opt/hatmmon/lib/libatmcmds.sl: ATM Networking rev. I.10.20.13 PHNE_25500 (14-Feb-02 _15:51, 7.39.4.3) /opt/hatmmon/lib/nls/msg/C/hatmmon.cat: None /opt/hatmmon/lib/nls/msg/C/hatmmone.cat: None /opt/hatmmon/share/man/man1m.Z/hatmmon.1m: None /opt/hatmmon/share/man/man1m.Z/serv_hatmmon.1m: None /usr/sam/lbin/atm.sh: None /usr/sam/lbin/atmupdate.sh: None /usr/sam/lib/kc/subsys.ATM.tx: None /usr/sam/lib/kc/params.ATM.tx: None /usr/sam/lib/kc/drivers.ATM.tx: None /usr/sam/lib/C/atmnia.ui: None /usr/sam/lib/C/atminuse.ui: None /usr/sam/lib/atm/atm.tm: atm.tm */ /usr/sam/lib/atm/atm.da: None /usr/sam/lib/atm/libatm.sl: ATM-SAM/HP-UX 10.X/Rev.C2.77 date:04/08/99 10:32:32 /usr/sam/help/C/atm/ATM.hv: None /usr/sam/help/C/atm/ATM.hvk: None /usr/sam/help/C/atm/ATM.xrh: None /usr/sam/help/C/atm/ATM00.ht: None /usr/sam/help/C/atm/ATM01.ht: None /usr/sam/help/C/atm/ATM02.ht: None cksum(1) Output: 3820928594 74964 /usr/conf/lib/libatmgsc.a 3742560454 200772 /usr/conf/lib/atmgsc_dbg.o 3089686579 4322 /usr/conf/master.d/atmgsc 2950585147 128176 /usr/conf/lib/libatm2gsc.a 1242753509 181484 /usr/conf/lib/atm2gsc_dbg.o 3732861397 4330 /usr/conf/master.d/atm2gsc 45683790 36864 /usr/sbin/alxdump 347099277 50072 /usr/conf/lib/libatmnio.a 2283836214 203284 /usr/conf/lib/atmnio_dbg.o 1430530863 4337 /usr/conf/master.d/atmnio 811229136 154264 /usr/conf/lib/libatm2pci.a 496863021 187784 /usr/conf/lib/atm2pci_dbg.o 1161035540 4344 /usr/conf/master.d/atm2pci 2399742648 1561060 /usr/conf/lib/libatm.a 1637431626 554844 /usr/conf/lib/atm_dbg.o 2577838070 4894 /usr/conf/master.d/atm 2009579691 106496 /usr/sbin/atminit 2728875668 57344 /usr/sbin/atmstop 1669054229 106496 /usr/sbin/atminit_net 1291582292 53248 /usr/sbin/atmstop_net 594091055 24576 /usr/sbin/atmtune 2972357330 69632 /usr/sbin/atmmgr 3768050845 69632 /usr/sbin/atmconfig 4285936041 32768 /usr/sbin/elstat 3690563544 32768 /usr/sbin/elarp 444144735 6108 /usr/lib/nls/msg/C/atminit.cat 3407368382 9341 /usr/lib/nls/msg/C/atmmgr.cat 2681125084 6101 /usr/lib/nls/msg/C/atmconfig.cat 1799426494 996 /usr/lib/nls/msg/C/elarp.cat 1411790108 986 /usr/lib/nls/msg/C/elstat.cat 2426629005 3555 /usr/lib/nls/msg/C/atmloop.cat 3993147177 3361 /usr/lib/nls/msg/C/atmcheck.cat 2140544740 3755 /usr/lib/nls/msg/C/atmserver.cat 1555559073 85551 /usr/lib/nls/msg/C/atm.cat 2536119484 2014 /usr/newconfig/etc/rc.config.d/atmconf 1970043873 13489 /sbin/init.d/atm 2812128630 16384 /usr/sbin/atmstrsrvd 3951618959 618496 /usr/lib/libatmfmt.sl 544210671 16384 /usr/sbin/atmdebug 173163182 36864 /usr/sbin/atmloop 339985536 36864 /usr/sbin/atmcheck 3923682630 36864 /usr/lbin/atmserver 2670605685 229376 /usr/lbin/ilmid 2186828048 2629 /usr/newconfig/etc/atm/ilmid.conf 4232259267 5035 /etc/atmrev/atm2to3 3645962800 10902 /etc/atmrev/atm3to4 1463819247 1635 /etc/atmrev/atm4to5 3149887817 19117 /usr/contrib/bin/atminfo 644405512 2989 /usr/share/man/man1m.Z/atmcheck.1m 644405512 2989 /usr/share/man/man1m.Z/atmserver.1m 3021942581 8548 /usr/share/man/man1m.Z/atminit.1m 3021942581 8548 /usr/share/man/man1m.Z/atminit_net.1m 3662399378 7631 /usr/share/man/man1m.Z/atmmgr.1m 2395379543 1238 /usr/share/man/man1m.Z/atmloop.1m 1674776955 1380 /usr/share/man/man1m.Z/atmstop.1m 1674776955 1380 /usr/share/man/man1m.Z/atmstop_net.1m 3663350231 5122 /usr/share/man/man1m.Z/atmconfig.1m 129058109 1297 /usr/share/man/man1m.Z/elarp.1m 2604607896 2140 /usr/share/man/man1m.Z/elstat.1m 974146939 12288 /opt/hatmmon/lib/libgendico.sl 2672958638 16384 /opt/hatmmon/lib/libgenreply.sl 262947697 24576 /opt/hatmmon/lib/libhaconfig.sl 3793790655 20480 /opt/hatmmon/sbin/hatmmon 643980313 12288 /opt/hatmmon/sbin/serv_hatmmon 3834657292 12354 /opt/hatmmon/sbin/hatmmigrate 1504136057 12288 /opt/hatmmon/lib/libatmconfig.sl 3399261840 20480 /opt/hatmmon/lib/libatmsts.sl 3586041115 20480 /opt/hatmmon/lib/libatmstse.sl 4224040775 20480 /opt/hatmmon/lib/libgenutil.sl 215051773 20480 /opt/hatmmon/lib/libgenutile.sl 1802907612 24576 /opt/hatmmon/lib/libshaconfig.sl 3380569666 16384 /opt/hatmmon/lib/libipaddr.sl 3323610445 16384 /opt/hatmmon/lib/libsamcfg.sl 3213957738 12288 /opt/hatmmon/lib/libatmcmds.sl 3995267856 3986 /opt/hatmmon/lib/nls/msg/C/hatmmon.cat 764099185 9292 /opt/hatmmon/lib/nls/msg/C/hatmmone.cat 1980342354 1942 /opt/hatmmon/share/man/man1m.Z/hatmmon.1m 988893910 2157 /opt/hatmmon/share/man/man1m.Z/ serv_hatmmon.1m 3063341060 40351 /usr/sam/lbin/atm.sh 1586834868 9106 /usr/sam/lbin/atmupdate.sh 783695286 632 /usr/sam/lib/kc/subsys.ATM.tx 3120600062 83 /usr/sam/lib/kc/params.ATM.tx 3818322797 575 /usr/sam/lib/kc/drivers.ATM.tx 2317403499 100713 /usr/sam/lib/C/atmnia.ui 2643930139 1337 /usr/sam/lib/C/atminuse.ui 2664895834 64236 /usr/sam/lib/atm/atm.tm 4000583297 3256 /usr/sam/lib/atm/atm.da 1991297211 163840 /usr/sam/lib/atm/libatm.sl 3556444312 15351 /usr/sam/help/C/atm/ATM.hv 1562564889 38 /usr/sam/help/C/atm/ATM.hvk 1656098897 10608 /usr/sam/help/C/atm/ATM.xrh 1555200249 81670 /usr/sam/help/C/atm/ATM00.ht 1105998684 3662 /usr/sam/help/C/atm/ATM01.ht 1630336456 6639 /usr/sam/help/C/atm/ATM02.ht Patch Conflicts: None Patch Dependencies: s700: 10.20: PHNE_12710 PHKL_12610 s800: 10.20: PHNE_12711 PHKL_12618 Hardware Dependencies: None Other Dependencies: None Supersedes: PHNE_22586 PHNE_21423 PHNE_10085 PHNE_10151 PHNE_10611 PHNE_11301 PHNE_11302 PHNE_12003 PHNE_12751 PHNE_13599 PHNE_14469 PHNE_15346 PHNE_17269 PHNE_18443 Equivalent Patches: None Patch Package Size: 5970 KBytes Installation Instructions: Please review all instructions and the Hewlett-Packard SupportLine User Guide or your Hewlett-Packard support terms and conditions for precautions, scope of license, restrictions, and, limitation of liability and warranties, before installing this patch. ------------------------------------------------------------ 1. Back up your system before installing a patch. 2. Login as root. 3. Copy the patch to the /tmp directory. 4. Move to the /tmp directory and unshar the patch: cd /tmp sh PHNE_25500 5a. For a standalone system, run swinstall to install the patch: swinstall -x autoreboot=true -x match_target=true \ -s /tmp/PHNE_25500.depot By default swinstall will archive the original software in /var/adm/sw/patch/PHNE_25500. If you do not wish to retain a copy of the original software, you can create an empty file named /var/adm/sw/patch/PATCH_NOSAVE. WARNING: If this file exists when a patch is installed, the patch cannot be deinstalled. Please be careful when using this feature. It is recommended that you move the PHNE_25500.text file to /var/adm/sw/patch for future reference. To put this patch on a magnetic tape and install from the tape drive, use the command: dd if=/tmp/PHNE_25500.depot of=/dev/rmt/0m bs=2k Special Installation Instructions: This patch installs only on release 3.0 or 6.0 of ATM which includes LAN Emulation, it will not install on ATM release 2.0 which product revision is B.10.20.*. You will need to install a later version, prior to installation of this patch. If this patch is installed on release 3.0 and the customer wants to go back to this release, he will have to remove the atm product, and then install the release 3.0 and the appropriate patches. This patch also improves the behavior in regard to the swverify errors caused by the control scripts in the PHNE_15346 patch. However, since the PHNE_15346 control scripts could not be fixed with this patch, if you install this patch on top of PHNE_15346, and then remove this patch, the swverify will disclose IPD synchronization errors. You may ignore them. As this patch works for both HSC and HP-PB ATM products, you may see some normal warnings about some files missing at installation. You may ignore them.