Patch Name: PHNE_15352 Patch Description: s700_800 10.20 2.40 ACC HDLC/LAP-B FW Patch Creation Date: 98/06/12 Post Date: 98/07/14 Hardware Platforms - OS Releases: s700: 10.20 s800: 10.20 Products: Z7408AA APZ Filesets: ACC-HDLC.ACC-HDLC-FW Automatic Reboot?: No Status: General Superseded Critical: No Path Name: /hp-ux_patches/s700_800/10.X/PHNE_15352 Symptoms: PHNE_15352: DTS TPO0h01936: 4-ch card: A DMA timeout can occur when disabling LAPD devices. DTS TPO0h02042: 4-ch card: LAPB/LAPD loses timers in the timer download control request. DTS TPO0h01946: 4-ch card: LAPB/LAPD can get frames out of sequence after receiving a REJ. SR 4701391862 / DTS TPO0h01966 No current method to determine hardware revision PHNE_14053: SR None / DTS TPO0h01833 8-channel NIO card crashes, with the use of the frame protocol and hdlcabm protocol together on the same port. SR None / DTS TPO0h01640 2 channel ACC card transmits a bad frame at the beginning of link setup. SR None / DTS TPO0h01641 When an unrecognised unnumbered frame is received at level2, the cause code information in the generated frame reject is incorrect. SR None / DTS TPO0h01755 hdlcabm sentr REJ on I-frame with duplicate N(s) Defect Description: PHNE_15352: DTS TPO0h01936: 4-ch card: When disabling LAPD devices which are under high message load the E1/T1 ACC card can "DMA timeout" due to internal linkages between remaining devices on the same subchannel being corrupted. DTS TPO0h02042: 4-ch card: When timers are downloaded to the LAPB/LAPD protocol in the CW_TIMERS control write request, a system timer entry is wasted. Eventually the ACC card can run out of timers. DTS TPO0h01946: 4-ch card: When the HDLCABM or X25 protocol receives a REJ frame while it is in the process of retransmitting frames, it can get transmitted frames out of sequence. SR 4701391862 / DTS TPO0h01966 Enhancement to detect hardware revisions of ACC cards. A standard interface has been defined to identify hardware revisions of all ACC cards. The 'mx' command of zmntr has been enhanced to include the display of the hardware revision. PHNE_14053: SR None / DTS TPO0h01833 Firmware failures with FRAME and HDLCABM concurrently in use. SR None / DTS TPO0h01640 2ch card transmits bad frame on link startup SR None / DTS TPO0h01641 frame reject cause information is bad on unknown frame type SR None / DTS TPO0h01755 hdlcabm sends REJ on I-frame with duplicate N(s) SR: 4701380642 4701391862 Patch Files: /opt/acc/z7200a/hdlc.zabs /opt/acc/z7200a/hdlc.zmap /opt/acc/z7350a/hdlc.zabs /opt/acc/z7350a/hdlc.zmap /opt/acc/z7400a/hdlc.zabs /opt/acc/z7400a/hdlc.zmap /opt/acc/protocol/hdlcabm.zrel /opt/acc/z7330a/download.zabs /opt/acc/z7300a/download.zabs what(1) Output: /opt/acc/z7200a/hdlc.zabs: ZCOM System Firmware (ROM) Rev 04.B 921106.1200 ACC Rel B.02.40 for B.10.20 PHNE_14053 z7200_snp.z8 0 ZCOM System Software (WMUX1) ACC Rel B.02.40 for B.10.20 PHNE_14053 wmux1.z80 ZCOM System Software (WMUX3) ACC Rel B.02.40 for B.10.20 PHNE_14053 wmux3.z80 CPU clock 16MHz ZCOM System Software (WMUX4) ACC Rel B.02.40 for B.10.20 PHNE_14053 wmux4.z80 ZCOM LEVEL1 Protocol ACC Rel B.02.40 for B.10.20 PHNE_14053 level1.z80 ZCOM HDLC ABM Protocol ACC Rel B.02.40 for B.10.20 PHNE_14053 abm.cpp ZCOM HDLC ABM State Tables Rev:1.12 971128.1444 ACC Rel B.02.40 for B.10.20 PHNE_14053 abmfsmtab.zi nc ZCOM Monitor Module ACC Rel B.02.40 for B.10.20 PHNE_14053 monitor.z80 ZCOM Port Diagnostic Module ACC Rel B.02.40 for B.10.20 PHNE_14053 testprot.z80 ZCOM Protocol Module Entry Point Table ACC Rel B.02.40 for B.10.20 PHNE_14053 pmenttab.z80 ZCOM System Entry Point Table ACC Rel B.02.40 for B.10.20 PHNE_14053 umuxent.z80 /opt/acc/z7200a/hdlc.zmap: ZCOM System Firmware (ROM) Rev 04.B 921106.1200 ACC Rel B.02.40 for B.10.20 PHNE_14053 z7200_snp.z8 0 ZCOM System Software (WMUX1) ACC Rel B.02.40 for B.10.20 PHNE_14053 wmux1.z80 ZCOM System Software (WMUX3) ACC Rel B.02.40 for B.10.20 PHNE_14053 wmux3.z80 CPU clock 16MHz ZCOM System Software (WMUX4) ACC Rel B.02.40 for B.10.20 PHNE_14053 wmux4.z80 ZCOM LEVEL1 Protocol ACC Rel B.02.40 for B.10.20 PHNE_14053 level1.z80 ZCOM HDLC ABM Protocol ACC Rel B.02.40 for B.10.20 PHNE_14053 abm.cpp ZCOM HDLC ABM State Tables Rev:1.12 971128.1444 ACC Rel B.02.40 for B.10.20 PHNE_14053 abmfsmtab.zi nc ZCOM Monitor Module ACC Rel B.02.40 for B.10.20 PHNE_14053 monitor.z80 ZCOM Port Diagnostic Module ACC Rel B.02.40 for B.10.20 PHNE_14053 testprot.z80 ZCOM Protocol Module Entry Point Table ACC Rel B.02.40 for B.10.20 PHNE_14053 pmenttab.z80 ZCOM System Entry Point Table ACC Rel B.02.40 for B.10.20 PHNE_14053 umuxent.z80 /opt/acc/z7350a/hdlc.zabs: ZCOM System Firmware (ROM) Rev 01.T5 ACC Rel B.02.40 for B.10.20 PHNE_14053 z7350_rom.z8 0 ZCOM Z7350A System Software ACC Rel B.02.40 for B.10.20 PHNE_14053 z7350_fw.z80 CPU clock 32MHz ZCOM LEVEL1 Protocol ACC Rel B.02.40 for B.10.20 PHNE_14053 level1.z80 ZCOM HDLC ABM Protocol ACC Rel B.02.40 for B.10.20 PHNE_14053 abm.cpp ZCOM HDLC ABM State Tables Rev:1.12 971128.1444 ACC Rel B.02.40 for B.10.20 PHNE_14053 abmfsmtab.zi nc ZCOM Monitor Module ACC Rel B.02.40 for B.10.20 PHNE_14053 monitor.z80 ZCOM Port Diagnostic Module ACC Rel B.02.40 for B.10.20 PHNE_14053 testprot_ius c.z80 ZCOM Protocol Module Entry Point Table ACC Rel B.02.40 for B.10.20 PHNE_14053 pmenttab.z80 /opt/acc/z7350a/hdlc.zmap: ZCOM System Firmware (ROM) Rev 01.T5 ACC Rel B.02.40 for B.10.20 PHNE_14053 z7350_rom.z8 0 ZCOM Z7350A System Software ACC Rel B.02.40 for B.10.20 PHNE_14053 z7350_fw.z80 CPU clock 32MHz ZCOM LEVEL1 Protocol ACC Rel B.02.40 for B.10.20 PHNE_14053 level1.z80 ZCOM HDLC ABM Protocol ACC Rel B.02.40 for B.10.20 PHNE_14053 abm.cpp ZCOM HDLC ABM State Tables Rev:1.12 971128.1444 ACC Rel B.02.40 for B.10.20 PHNE_14053 abmfsmtab.zi nc ZCOM Monitor Module ACC Rel B.02.40 for B.10.20 PHNE_14053 monitor.z80 ZCOM Port Diagnostic Module ACC Rel B.02.40 for B.10.20 PHNE_14053 testprot_ius c.z80 ZCOM Protocol Module Entry Point Table ACC Rel B.02.40 for B.10.20 PHNE_14053 pmenttab.z80 /opt/acc/z7400a/hdlc.zabs: ZCOM System Firmware (ROM) Rev 01.B5 ACC Rel B.02.40 for B.10.20 PHNE_14053 z7400_rom.z8 0 ZCOM Z7400A System Software ACC Rel B.02.40 for B.10.20 PHNE_14053 z7400_fw.z80 ZCOM LEVEL1 Protocol ACC Rel B.02.40 for B.10.20 PHNE_14053 level1.z80 ZCOM HDLC ABM Protocol ACC Rel B.02.40 for B.10.20 PHNE_14053 abm.cpp ZCOM HDLC ABM State Tables Rev:1.12 971128.1444 ACC Rel B.02.40 for B.10.20 PHNE_14053 abmfsmtab.zi nc ZCOM Monitor Module ACC Rel B.02.40 for B.10.20 PHNE_14053 monitor.z80 ZCOM Port Diagnostic Module ACC Rel B.02.40 for B.10.20 PHNE_14053 testprot.z80 ZCOM Protocol Module Entry Point Table ACC Rel B.02.40 for B.10.20 PHNE_14053 pmenttab.z80 /opt/acc/z7400a/hdlc.zmap: ZCOM System Firmware (ROM) Rev 01.B5 ACC Rel B.02.40 for B.10.20 PHNE_14053 z7400_rom.z8 0 ZCOM Z7400A System Software ACC Rel B.02.40 for B.10.20 PHNE_14053 z7400_fw.z80 ZCOM LEVEL1 Protocol ACC Rel B.02.40 for B.10.20 PHNE_14053 level1.z80 ZCOM HDLC ABM Protocol ACC Rel B.02.40 for B.10.20 PHNE_14053 abm.cpp ZCOM HDLC ABM State Tables Rev:1.12 971128.1444 ACC Rel B.02.40 for B.10.20 PHNE_14053 abmfsmtab.zi nc ZCOM Monitor Module ACC Rel B.02.40 for B.10.20 PHNE_14053 monitor.z80 ZCOM Port Diagnostic Module ACC Rel B.02.40 for B.10.20 PHNE_14053 testprot.z80 ZCOM Protocol Module Entry Point Table ACC Rel B.02.40 for B.10.20 PHNE_14053 pmenttab.z80 /opt/acc/protocol/hdlcabm.zrel: ZCOM HDLC ABM Protocol ACC Rel B.02.40 for B.10.20 PHNE_14053 abm.cpp ZCOM HDLC ABM State Tables Rev:1.12 971128.1444 ACC Rel B.02.40 for B.10.20 PHNE_14053 abmfsmtab.zi nc /opt/acc/z7330a/download.zabs: ACC Rel B.02.40 for B.10.20 PHNE_15352 ACC Base F/W ACC Rel B.02.40 for B.10.20 PHNE_15352 LAP-B Protoco l F/W ACC Rel B.02.40 for B.10.20 PHNE_15352 LAP-D Protoco l F/W ACC Rel B.02.40 for B.10.20 PHNE_15352 X.25 Protocol F/W /opt/acc/z7300a/download.zabs: ACC Rel B.02.40 for B.10.20 PHNE_15352 ACC Base F/W ACC Rel B.02.40 for B.10.20 PHNE_15352 LAP-B Protoco l F/W ACC Rel B.02.40 for B.10.20 PHNE_15352 LAP-D Protoco l F/W ACC Rel B.02.40 for B.10.20 PHNE_15352 X.25 Protocol F/W cksum(1) Output: 3505799623 24626 /opt/acc/z7200a/hdlc.zabs 852565348 19488 /opt/acc/z7200a/hdlc.zmap 1394136072 23914 /opt/acc/z7350a/hdlc.zabs 3579587064 18325 /opt/acc/z7350a/hdlc.zmap 2207143529 24644 /opt/acc/z7400a/hdlc.zabs 3878028501 18152 /opt/acc/z7400a/hdlc.zmap 3633438602 27910 /opt/acc/protocol/hdlcabm.zrel 2534137561 1872766 /opt/acc/z7330a/download.zabs 3913521135 1727234 /opt/acc/z7300a/download.zabs Patch Conflicts: None Patch Dependencies: None Hardware Dependencies: None Other Dependencies: None Supersedes: PHNE_14053 Equivalent Patches: None Patch Package Size: 3740 KBytes Installation Instructions: Please review all instructions and the Hewlett-Packard SupportLine User Guide or your Hewlett-Packard support terms and conditions for precautions, scope of license, restrictions, and, limitation of liability and warranties, before installing this patch. ------------------------------------------------------------ 1. Back up your system before installing a patch. 2. Login as root. 3. Copy the patch to the /tmp directory. 4. Move to the /tmp directory and unshar the patch: cd /tmp sh PHNE_15352 5a. For a standalone system, run swinstall to install the patch: swinstall -x autoreboot=true -x match_target=true \ -s /tmp/PHNE_15352.depot 5b. For a homogeneous NFS Diskless cluster run swcluster on the server to install the patch on the server and the clients: swcluster -i -b This will invoke swcluster in the interactive mode and force all clients to be shut down. WARNING: All cluster clients must be shut down prior to the patch installation. Installing the patch while the clients are booted is unsupported and can lead to serious problems. The swcluster command will invoke an swinstall session in which you must specify: alternate root path - default is /export/shared_root/OS_700 source depot path - /tmp/PHNE_15352.depot To complete the installation, select the patch by choosing "Actions -> Match What Target Has" and then "Actions -> Install" from the Menubar. 5c. For a heterogeneous NFS Diskless cluster: - run swinstall on the server as in step 5a to install the patch on the cluster server. - run swcluster on the server as in step 5b to install the patch on the cluster clients. By default swinstall will archive the original software in /var/adm/sw/patch/PHNE_15352. If you do not wish to retain a copy of the original software, you can create an empty file named /var/adm/sw/patch/PATCH_NOSAVE. Warning: If this file exists when a patch is installed, the patch cannot be deinstalled. Please be careful when using this feature. It is recommended that you move the PHNE_15352.text file to /var/adm/sw/patch for future reference. To put this patch on a magnetic tape and install from the tape drive, use the command: dd if=/tmp/PHNE_15352.depot of=/dev/rmt/0m bs=2k Special Installation Instructions: SUBSYSTEM_SHUT After installing this patch, the ACC subsystem must then be stopped and restarted using zmasterd in order to download the new firmware.