Patch Name: PHNE_13940 Patch Description: s700_800 10.20 HSC 100BT lan cumulative patch Creation Date: 98/01/29 Post Date: 98/02/11 Repost: 98/03/26 The patch documentation was modified to add Patch Dependency information on PHNE_14501 and PHNE_14502. Patch PHNE_13940 enables manual speed and duplex configuration of the 100BT card, but patches PHNE_14501 (s700) or PHNE_14502 (s800) are necessary to update the lanadmin(1M) command to support the speed and mode changes. The files installed by the patch have not been modified. Hardware Platforms - OS Releases: s700: 10.20 s800: 10.20 Products: J3621AA_APZ B.10.20.00 100BT/9000 GSC J3621AA_APZ B.10.20.01 100BT/9000 GSC J3621AA_APZ B.10.20.02 100BT/9000 GSC J3621AA_APZ B.10.20.03 100BT/9000 GSC J3621AA_APZ B.10.20.04 100BT/9000 GSC J3620BA B.10.20.04 100BT/9000 GSC J3623BA B.10.20.04 100BT/9000 GSC Filesets: 100BT-GSC-KRN.100BT-KRN,B.10.20.00 100BT-GSC-KRN.100BT-KRN,B.10.20.01 100BT-GSC-KRN.100BT-KRN,B.10.20.02 100BT-GSC-KRN.100BT-KRN,B.10.20.03 100BT-GSC-KRN.100BT-KRN,B.10.20.04 100BT-GSC-RUN.100BT-RUN,B.10.20.00 100BT-GSC-RUN.100BT-RUN,B.10.20.01 100BT-GSC-RUN.100BT-RUN,B.10.20.02 100BT-GSC-RUN.100BT-RUN,B.10.20.03 100BT-GSC-RUN.100BT-RUN,B.10.20.04 100BT-GSC-RUN.100BT-INIT,B.10.20.00 100BT-GSC-RUN.100BT-INIT,B.10.20.01 100BT-GSC-RUN.100BT-INIT,B.10.20.02 100BT-GSC-RUN.100BT-INIT,B.10.20.03 100BT-GSC-RUN.100BT-INIT,B.10.20.04 Automatic Reboot?: Yes Status: General Superseded Critical: No (superseded patches were critical) PHNE_12400: PANIC PHNE_11229: OTHER Changing link address with 100bt makes ARP fail. Path Name: /hp-ux_patches/s700_800/10.X/PHNE_13940 Symptoms: PHNE_13940: The following symptoms are seen for PHNE_13940: 1. When the AUI port is connected lanscan still shows the hardware state as being down. 2. Driver reports receive errors under heavy traffic PHNE_12400: The following symptoms are seen for PHNE_12400: 1. System panic in the btlan4 driver code. 2. HSC 100BT port hung. PHNE_11229: The following symptoms are seen for PHNE_11229. 1. Changing the link address with 100bt makes ARP fail. 2. GSC 100BT driver reports incorrect statistics. 3. Lanadmin shows incorrect (bogus) value for outbound queue on HSC 100BT. 4. Receive performance will not be as good as with this patch. 5. FTP hangs. 6. Problem with 10BT and noheartbeats. 7. Low performance due to IEEE SNAP packets not being logged and going through expensive lanc_logging. 8. Cable disconnect/reconnect interrupts are not always acknowledged. 9. DHCP does not work correctly with GSC 100BT. Defect Description: PHNE_13940: The following defect descriptions are for PHNE_13940: 1. The AUI port was not being properly initialized. 2. Under heavy inbound traffic for a long period of time, the number of empty descriptors became incorrect. 3. Manual Speed and Duplex configuration is now enabled. PHNE_12400: The following defect descriptions are for PHNE_12400: 1. Under heavy inbound traffic for a long period of time, btlan4 driver will eventually exhaust all the receive descriptors and it can cause port hang or system panic. PHNE_11229: The following defect descriptions are for PHNE_11229. 1. Changing link address with 100bt makes ARP fail. 2. GSC 100BT driver reports incorrect statistics. 3. Lanadmin shows incorrect (bogus) value for outbound queue on HSC 100BT. 4. Modified receive path to increase performance. Use schednetisrmq instead of the older schednetisrsq. 5. Transmit and Receive data structures were not properly zero'ed out during initialization. This caused FTP's to occasionally hang the system. 6. Noheartbeat errors must be disabled when in 10BT mode. Otherwise, output packet counts will not be properly updated. 7. Low performance due to IEEE SNAP packets not being logged and going through expensive lanc_logging. 8. Transmit and Receive interrupts are not acknowledged during cable disconnect/reconnect conditions. 9. Fixed bug in BTLAN3_DO_FAST_IN which failed to check the strip header flag. This caused the GSC 100BT driver to not work correctly with DHCP. SR: 4701355917 1653232306 4701365569 5003405175 5003405225 1653240432 5003398388 Patch Files: /usr/conf/lib/libbtlan4.a /usr/lib/lanadmin/libdsbtlan4.sl /usr/newconfig/etc/rc.config.d/hpgsc100conf /sbin/init.d/hpgsc100 what(1) Output: /usr/conf/lib/libbtlan4.a: btlan4.c GSC 100BT 10.20 PHNE_13940 $Revision: 2.10 $ $Date: 98/01/29 10:34:27 $ /usr/lib/lanadmin/libdsbtlan4.sl: libdsbtlan4.sl: Version: B.10.20 $Date: 98/01/26 14 :14:12 $ /usr/newconfig/etc/rc.config.d/hpgsc100conf: hpGSC100conf PHNE_13940 $Revision: 1.2 $ $Date: 98/0 1/29 12:00:01 $ /sbin/init.d/hpgsc100: hpgsc100 PHNE_13940 $Revision: 1.2 $ $Date: 98/01/29 12:00:00 $ cksum(1) Output: 3357716449 109804 /usr/conf/lib/libbtlan4.a 1631808457 20528 /usr/lib/lanadmin/libdsbtlan4.sl 2783070780 1231 /usr/newconfig/etc/rc.config.d/hpgsc100conf 1979808167 6282 /sbin/init.d/hpgsc100 Patch Conflicts: None Patch Dependencies: s700: 10.20: PHKL_11351 PHNE_14501 s800: 10.20: PHKL_11352 PHNE_14502 Hardware Dependencies: None Other Dependencies: None Supersedes: PHNE_11229 PHNE_12400 Equivalent Patches: None Patch Package Size: 210 KBytes Installation Instructions: Please review all instructions and the Hewlett-Packard SupportLine User Guide or your Hewlett-Packard support terms and conditions for precautions, scope of license, restrictions, and, limitation of liability and warranties, before installing this patch. ------------------------------------------------------------ 1. Back up your system before installing a patch. 2. Login as root. 3. Copy the patch to the /tmp directory. 4. Move to the /tmp directory and unshar the patch: cd /tmp sh PHNE_13940 5a. For a standalone system, run swinstall to install the patch: swinstall -x autoreboot=true -x match_target=true \ -s /tmp/PHNE_13940.depot 5b. For a homogeneous NFS Diskless cluster run swcluster on the server to install the patch on the server and the clients: swcluster -i -b This will invoke swcluster in the interactive mode and force all clients to be shut down. WARNING: All cluster clients must be shut down prior to the patch installation. Installing the patch while the clients are booted is unsupported and can lead to serious problems. The swcluster command will invoke an swinstall session in which you must specify: alternate root path - default is /export/shared_root/OS_700 source depot path - /tmp/PHNE_13940.depot To complete the installation, select the patch by choosing "Actions -> Match What Target Has" and then "Actions -> Install" from the Menubar. 5c. For a heterogeneous NFS Diskless cluster: - run swinstall on the server as in step 5a to install the patch on the cluster server. - run swcluster on the server as in step 5b to install the patch on the cluster clients. By default swinstall will archive the original software in /var/adm/sw/patch/PHNE_13940. If you do not wish to retain a copy of the original software, you can create an empty file named /var/adm/sw/patch/PATCH_NOSAVE. Warning: If this file exists when a patch is installed, the patch cannot be deinstalled. Please be careful when using this feature. It is recommended that you move the PHNE_13940.text file to /var/adm/sw/patch for future reference. To put this patch on a magnetic tape and install from the tape drive, use the command: dd if=/tmp/PHNE_13940.depot of=/dev/rmt/0m bs=2k Special Installation Instructions: None