Patch Name: PHKL_14528 Patch Description: s700 10.24 (VVOS) J2240, PCI, GSCtoPCI cumulative patch Creation Date: 98/03/17 Post Date: 98/03/26 Hardware Platforms - OS Releases: s700: 10.24 Products: N/A Filesets: OS-Core.CORE-KRN ProgSupport.C-INC Automatic Reboot?: Yes Status: General Release Critical: Yes PHKL_14528: OTHER Port I/O will not work correctly, machine may panic. PHKL_12645: PANIC Path Name: /hp-ux_patches/s700/10.X/PHKL_14528 Symptoms: PHKL_14528: Repackaged HP-UX patch PHKL_13868 for VVOS. Note: Although the HP-UX patch below refers to T600, T600 is not supported on 10.24. The VVOS version of the patch fixes other problems enumerated by the HP-UX patches. Based on HP-UX patch PHKL_13868: PCI port I/O does not work properly, and machine may panic. Based on HP-UX patch PHKL_13514: With certain hardware configurations, especially on the J2240, it is possible for the system to panic (at bootup) with the message: panic: Could not assign interrupt handler PHKL_12645: Repackaged HP-UX patch PHKL_11351 for VVOS. Based on HP-UX patch PHKL_11351: (DSDe438658) panic: Data Page Fault with FDDI. T600 will HPMC when HSC (GSC) interface cards using a GSCtoPCI interface chip are installed. (4701362111) Any MP system is likely to panic when multiple HSC (GSC) interface cards using GSCtoPCI interface chips are installed. (DSDe437012) Performance enhancement in PCI services. Based on HP-UX patch PHKL_10756: This patch contains enhancements to support the GSCtoPCI PCI Bus Bridge on HP workstations. Defect Description: PHKL_14528: Repackaged HP-UX patch PHKL_13868 for VVOS. Based on HP-UX patch PHKL_13868: Incorrect values were being written to port I/O registers. Based on HP-UX patch PHKL_13514: This defect is due to an error in the Dino CDIO regarding the reservation and assignment of interrupt resources. PHKL_12645: Repackaged HP-UX patch PHKL_11351 for VVOS. Based on HP-UX patch PHKL_11351: The GSC "I/O Adapter" was not designed to support one of the GSC control lines used by the GSCtoPCI interface chip. The GSCtoPCI services now avoids using this control line. Shared IRQ panics are due to a subtle bug in the way interrupt service routine lists are managed. (DSDe437012) Shortened code paths in PCI services. All HP-UX PCI drivers will benefit from this. (DSDe438658) Added support for an additional return value from PCI services (to FDDI driver). Based on HP-UX patch PHKL_10756: Support for GSCtoPCI PCI Bus Bridge in "card mode". SR: 4701354803 4701355123 4701362111 4701377580 4701379354 Patch Files: /usr/conf/lib/libhp-ux.a(pci_debug.o) /usr/conf/lib/libpci.a(dino3.o) /usr/conf/lib/libpci.a(dino_cdio.o) /usr/conf/lib/libpci.a(h2p_iface.o) /usr/conf/lib/libpci.a(pci.o) /usr/conf/lib/libpci.a(pci_cdio.o) /usr/conf/lib/libpci.a(pci_wsio.o) /usr/conf/wsio/pci.h /usr/include/sys/pci.h what(1) Output: /usr/conf/lib/libhp-ux.a(pci_debug.o): pci_debug.c $Date: 97/08/18 18:35:45 $ $Revision : 1.2.98.3 $ PATCH_10.20 (PHKL_11351) /usr/conf/lib/libpci.a(dino3.o): dino3.c $Date: 98/01/14 15:14:39 $ $Revision: 1.2.98.6 $ PATCH_10.20 (PHKL_13813) /usr/conf/lib/libpci.a(dino_cdio.o): dino_cdio.c $Date: 98/01/19 14:37:27 $ $Revision: 1.2.98.22 $ PATCH_10.20 (PHKL_13868) /usr/conf/lib/libpci.a(h2p_iface.o): h2p_iface.c $Date: 97/08/18 18:14:02 $ $Revision: 1.2.98.15 $ PATCH_10.20 (PHKL_11351) /usr/conf/lib/libpci.a(pci.o): pci.c $Date: 97/08/18 18:14:05 $ $Revision: 1.2.98.15 $ PATCH_10.20 (PHKL_11351) /usr/conf/lib/libpci.a(pci_cdio.o): pci_cdio.c $Date: 97/08/18 18:14:07 $ $Revision: 1.2.98.13 $ PATCH_10.20 (PHKL_11351) /usr/conf/lib/libpci.a(pci_wsio.o): pci_wsio.c $Date: 97/08/18 18:14:08 $ $Revision: 1.2.98.8 $ PATCH_10.20 (PHKL_11351) /usr/conf/wsio/pci.h: pci.h $Date: 97/05/02 13:31:36 $ $Revision: 1.2.98.11 $ PATCH_10.20 (PHKL_10756) /usr/include/sys/pci.h: pci.h $Date: 97/05/02 13:31:36 $ $Revision: 1.2.98.11 $ PATCH_10.20 (PHKL_10756) cksum(1) Output: 270772003 41252 /usr/conf/lib/libhp-ux.a(pci_debug.o) 908300963 9040 /usr/conf/lib/libpci.a(dino3.o) 1225572497 18280 /usr/conf/lib/libpci.a(dino_cdio.o) 1275340326 9676 /usr/conf/lib/libpci.a(h2p_iface.o) 2053636511 1908 /usr/conf/lib/libpci.a(pci.o) 2993723634 7256 /usr/conf/lib/libpci.a(pci_cdio.o) 4009235679 4212 /usr/conf/lib/libpci.a(pci_wsio.o) 45607075 23885 /usr/conf/wsio/pci.h 45607075 23885 /usr/include/sys/pci.h Patch Conflicts: None Patch Dependencies: None Hardware Dependencies: None Other Dependencies: None Supersedes: PHKL_12645 Equivalent Patches: PHKL_14529: s800: 10.24 Patch Package Size: 210 KBytes Installation Instructions: Please review all instructions and the Hewlett-Packard SupportLine User Guide or your Hewlett-Packard support terms and conditions for precautions, scope of license, restrictions, and, limitation of liability and warranties, before installing this patch. ------------------------------------------------------------ 1. Back up your system before installing a patch. 2. Login as root. 3. Copy the patch to the /tmp directory. 4. Move to the /tmp directory and unshar the patch: cd /tmp sh PHKL_14528 5a. For a standalone system, run swinstall to install the patch: swinstall -x autoreboot=true -x match_target=true \ -s /tmp/PHKL_14528.depot 5b. For a homogeneous NFS Diskless cluster run swcluster on the server to install the patch on the server and the clients: swcluster -i -b This will invoke swcluster in the interactive mode and force all clients to be shut down. WARNING: All cluster clients must be shut down prior to the patch installation. Installing the patch while the clients are booted is unsupported and can lead to serious problems. The swcluster command will invoke an swinstall session in which you must specify: alternate root path - default is /export/shared_root/OS_700 source depot path - /tmp/PHKL_14528.depot To complete the installation, select the patch by choosing "Actions -> Match What Target Has" and then "Actions -> Install" from the Menubar. 5c. For a heterogeneous NFS Diskless cluster: - run swinstall on the server as in step 5a to install the patch on the cluster server. - run swcluster on the server as in step 5b to install the patch on the cluster clients. By default swinstall will archive the original software in /var/adm/sw/patch/PHKL_14528. If you do not wish to retain a copy of the original software, you can create an empty file named /var/adm/sw/patch/PATCH_NOSAVE. Warning: If this file exists when a patch is installed, the patch cannot be deinstalled. Please be careful when using this feature. It is recommended that you move the PHKL_14528.text file to /var/adm/sw/patch for future reference. To put this patch on a magnetic tape and install from the tape drive, use the command: dd if=/tmp/PHKL_14528.depot of=/dev/rmt/0m bs=2k Special Installation Instructions: None