SOFTPAQ NUMBER: SP9503 PART NUMBER: 277068-298, 277069-298, 277070-298, 277071-298 FILE NAME: N/A TITLE: Compaq Server Support for Microsoft Windows NT 4.0 VERSION: 2.12 Rev A LANGUAGE: Japanese CATEGORY: Drivers DIVISIONS: Systems PRODUCTS AFFECTED: All Compaq Servers OPERATING SYSTEM: Microsoft Windows NT Version 4.0 (Japanese) SYSTEM CONFIGURATION: N/A PREREQUISITES: N/A EFFECTIVE DATE: January 21, 1999 ELECTRONIC DISTRIBUTION ALLOWED: Yes SOFTPAQ UTILITY VERSION: 2.x SUPERSEDES: SP8471 DESCRIPTION: This SoftPaq is for Japanese products, and cannot be run in United States mode. There are a total of four diskettes with this release. The SSD supports the following subsystems and features of Compaq Servers. ATI Rage IIC Video Display Controller Compaq Advanced Network Control Utility Compaq Cluster Verification Utility Compaq Enhanced Integrated Management Display Service Compaq Ethernet or Fast Ethernet Controllers Compaq NC1120 Ethernet NIC Compaq NC3120 Fast Ethernet NIC Compaq NC3122 Fast Ethernet NIC Compaq NC3160 Fast Ethernet NIC Compaq NC3161 Fast Ethernet NIC Compaq Fibre Channel Storage System Compaq Fibre Channel Host Controllers SCSI Miniport Driver Compaq Fibre Channel Array Controllers SCSI Class Driver Compaq Fibre Channel Filter Driver Compaq Integrated Management Display Utility Compaq Integrated Management Log Viewer Compaq Netelligent Family of Controllers Compaq Netelligent 10 T/2 PCI UTP/Coax Controller Compaq Netelligent 10 T PCI UTP Controller Compaq Netelligent 10/100 TX PCI UTP Controller Compaq Netelligent Dual 10/100 TX PCI UTP Controller Compaq Netelligent 10/100 TX Embedded UTP/Coax Controller Compaq Netelligent 10/100 TX Embedded UTP/AUI Controller Compaq Netelligent 10/100 TX Embedded UTP Controller Compaq NetFlex-3 Family of Controllers Compaq NetFlex-3/P Controller Compaq NetFlex-3/E Controller Compaq Online Storage Controller Recovery Utility Compaq PCI Hot Plug Utility Compaq Power Down Manager Compaq Power Supply Viewer Compaq ProLiant Storage System Compaq Recovery Server, Standby Agent with SMART-2 Support Compaq Recovery Server, Online Agent with SMART-2 Support Compaq Remote Insight Board Driver Compaq Remote Insight Board WAN Driver Compaq Remote Monitor Service Compaq SCSI Controllers Compaq Dual Channel Integrated Wide-Ultra SCSI-3 Controller Compaq Wide-Ultra SCSI-3 Controller Compaq 32-Bit Fast-Wide SCSI-2/E Controller Fast-SCSI-2 Controller Integrated PCI SCSI-2 Controller Integrated 32-Bit Fast-SCSI-2/P Controller Integrated 32-Bit Fast-Wide SCSI-2/P Controller Integrated Wide-Ultra SCSI Controller Fast-SCSI-2 Controller option board Compaq Dual Channel Wide-Ultra SCSI-3 Controller option board Compaq Wide-Ultra SCSI-3 Controller option board Compaq 32-Bit Fast-Wide SCSI-2/E Controller option board Integrated 32-Bit Fast-Wide SCSI-2/P Controller option board Compaq Server Support Installation Utility Compaq SMART/SMART-2 Family of Array Controllers Compaq SMART/IDA-2/IDA/IAES Array Controllers Compaq SMART-2/P and Compaq SMART-2/E Array Controllers Compaq SMART-2DH Array Controller Compaq SMART-2SL Array Controller Compaq Smart Array 3100ES Controller Compaq Smart Array 3200 Controller Compaq System Management/Health Driver The following diskettes can be created using the files that result when the SoftPaq is unbundled: Disk 1 - Compaq Server Support for Microsoft NT 4.0 Disk #1 Disk 2 - Compaq Server Support for Microsoft NT 4.0 Disk #2 Disk 3 - Compaq Server Support for Microsoft NT 4.0 Disk #3 Disk 4 - Compaq Server Support for Microsoft NT 4.0 Disk #4 Enhancements/Fixes: The release of the Compaq Server Support for Microsoft Windows NT 4.0 Version 2.12 Revision A, primarily supports the following new products: - Compaq Prosignia 720 6/350 - Compaq Prosignia 720 6/400 - Compaq ProLiant 400 6/350 Model 1 - Compaq ProLiant 400 6/350 Model 4300 - Compaq ProLiant 400 6/400 Model 1 - Compaq ProLiant 400 6/400 Model 4300 - Compaq ProLiant 400 6/450 Model 1 - Compaq ProLiant 5500 6/450-1 - Compaq ProLiant 5500R 6/450-1 - Compaq ProLiant 5500 6/450-2 - Compaq ProLiant 5500R 6/450-2 - Compaq Smart Array 221 Controller Compaq Fibre Channel Array Controllers SCSI Class Driver(CPQFCAC.SYS) - Fixed a problem with the CPQFCAC.INF file not recognizing the correct Compaq SSD for Windows NT 4.0 diskette upon insertion. Compaq Fibre Channel Filter Driver(CPQFCFTR.SYS) - Fixed a problem with the CPQFCFTR.INF file not recognizing the correct Compaq SSD for Windows NT 4.0 diskette upon insertion. Compaq Fibre Channel Host Controllers SCSI Miniport Driver(CPQFCALM.SYS) - Added support for virtual LUN (Logical Unit Number) capability. This support allows hot adding drives to a Compaq Fibre Channel Host Controller with no targets. - Changed version-numbering scheme of the Compaq Fibre Channel Host Controllers SCSI Miniport Driver from 1.xx to 4.xx. - Fixed problem with World Wide ID of non-Compaq devices appearing as being byte swapped in Compaq Insight Manager and other applications that gather information from driver. - Improved the detection of lost login frames. - Fixed a bug that would prevent a Compaq Fibre Channel Host Controller from receiving a fibre channel loop address. - Fixed a problem with the CPQFCALM.INF file not recognizing the correct Compaq SSD for Windows NT 4.0 diskette upon insertion. Compaq 4/8-GB SLR Tape Driver(TANDQIC.SYS) - Removed the Compaq 4/8-GB SLR Tape Driver files from the Compaq SSD for Windows NT 4.0 release. These files are available from the Compaq Web site at www.compaq.com as SoftPaq number 5982. Compaq Remote Insight Board Driver(CPQRIB.SYS) Updated the Compaq Remote Insight Board Driver version from 1.50 to 1.51. Version 1.51 corrects an issue where the previous version of the Compaq Remote Insight Board Driver would not start on a multiprocessor Compaq ProLiant 3000 or 5500 configured as follows: Compaq Remote Insight Board/EISA and system ROM dated later than 3/98. Compaq Remote Insight Board/PCI WAN Driver(RIBWAN.SYS) - Updated the RIBWAN.INF file to re-enable the Compaq Remote Insight Board/PCI Driver, along with the Compaq Remote Insight Board/PCI WAN Driver, after it is installed and removed using Compaq Server Support Setup for Microsoft Windows NT then reinstalled through the Windows NT Control Panel using the RIBWAN.INF file. - Fixed a Compaq Remote Insight Board/PCI WAN routing issue. In the Compaq Remote Insight Board User Guide, you are asked to perform the "route add A B" command, where A and B are IP addresses. In previous Compaq SSD for Windows NT 4.0 versions, the packets destined for target A are not routed through the device properly if B is an IP address on one of the Compaq Remote Insight Board/PCI WAN endpoints. Beginning in Compaq SSD for Windows NT 4.0 Version 2.12A, the packets destined for IP address A are properly routed through IP address B, which is the Compaq Remote Insight Board/PCI WAN device. Compaq Server Support Setup for Microsoft Windows NT 4.0(SETUP.EXE) - Added support to upgrade/downgrade your HAL if Microsoft Service Pack 4 is installed on your system. - Modified Compaq Server Support Setup for Microsoft Windows NT 4.0 to disallow installation of the Compaq SCSI Controller Driver, the Compaq SMART/SMART-2 Array Controller Driver, or the Compaq Fibre Channel Host Controllers SCSI Miniport Driver if it detects that you have removed the driver through the Windows NT Control Panel. Once the driver has been uninstalled from the Windows NT Control Panel, you must reboot the system or reinstall the driver through the Windows NT Control Panel. - Added a new popup, indicating the supported version of the Compaq Array Configuration Utility that is supported in this Compaq SSD for Windows NT 4.0 release, which will appear after the option to install the utility has been selected. - Added an enhancement to indicate when you should update the Compaq Array Configuration Utility on your system. - Removed the capability for Compaq Server Support Setup for Microsoft Windows NT 4.0 Version 2.12A (or later) to operate on Compaq Professional Workstation products. - Added support for the Compaq NC3161 Fast Ethernet NIC. - Modified Compaq Server Support Setup for Microsoft Windows NT 4.0 to prompt you to update the Compaq Remote Insight Board/PCI WAN Driver after installing RAS to ensure that a registry setting created by the RAS install has the correct value for this driver. If this driver is not updated after a RAS install is performed, the registry value will be incorrect, disabling the "route add A B" command functionality that was fixed in this release (see the "Compaq Remote Insight Board/PCI WAN Driver(RIBWAN.SYS)" entry in this section). Compaq SCSI Controller Driver(CPQ32FS2.SYS) - Updated the Compaq SCSI Controller Driver version from 3.19 to 3.21. - Added support to the Compaq SCSI Controller Driver for the following new products: Compaq Prosignia 720 6/350 Compaq Prosignia 720 6/400 Compaq 64-Bit Dual Channel Wide-Ultra2 SCSI Controller. - Fixed a problem with the FASTSCSI.INF file not recognizing the correct Compaq SSD for Windows NT 4.0 diskette upon insertion. - Changed Compaq Pseudo Device type from UNSUPPORTED to UNKNOWN. - Fixed a performance degradation problem observed on fast disk drives upon removal and reinsertion. - Changed the driver name in the file properties from Compaq 32-Bit SCSI-2 Controllers to Compaq SCSI Controllers. Compaq SMART/SMART-2 Array Controller Driver(CPQARRAY.SYS) - Fixed a problem with the CPQARRAY.INF file not recognizing the correct Compaq SSD for Windows NT 4.0 diskette upon insertion. Compaq System Management Driver(SYSMGMT.SYS) - Updated the Compaq System Management Driver version from 3.12.01 to 3.15.01. Version 3.15.01 of the Compaq System Management Driver corrects the loss of system fan, thermal, power supply, and ECC monitoring that Version 3.12.01 causes on the following systems: Compaq ProLiant 800 6/350 Compaq ProLiant 1600 (Models 6/350, 6/400, and 6/450-1) Compaq ProLiant 1600R (Models 6/400 and 6/450-1) - Added support to the Compaq System Management Driver for the following new Compaq servers: Compaq Prosignia 720 6/350 Compaq Prosignia 720 6/400. - Removed support for all models of the Compaq Professional Workstation. Full support for the Compaq Professional Workstation series is now available on Compaq Workstation Support Software for Microsoft Windows NT 4.0 Version 2.00 (or later). - Corrected the display of erroneous data in the Compaq Insight Manager console. This invalid data appeared when a 400-Watt Hot Plug Redundant Power Supply Upgrade Kit was installed on the following systems: Compaq ProLiant 1600 6/350-1 Compaq ProLiant 1600 6/400-1 Compaq ProLiant 1600R 6/400-1. For details, refer to NTREADME.HLP located on diskette #1 HOW TO USE: 1. Obtain four (4) formatted 1.44 MB diskettes. 2. Download the SoftPaq to a directory on your hard drive and change to that directory. The file that is downloaded is an executable with a filename based on the SoftPaq Number above. 3. From that drive and directory, execute the downloaded file and follow the on-screen instructions. You will be prompted to insert the formatted diskettes in a drive to create the diskettes. 4. After the diskettes have been created, you may delete the SoftPaq file downloaded in step 2. 5. For installation instructions, run README on the 1st created diskette. Copyright 1999, Compaq Computer Corporation. All rights reserved. Product names mentioned herein may be trademarks and/or registered trademarks of their respective companies