SOFTPAQ NUMBER: SP3182 PART NUMBER: N/A FILE NAME: IOS0411.EXE TITLE: Netelligent 8500 Open Communications Platform VERSION: 1.2 LANGUAGE: English CATEGORY: Software Solutions/Misc PRODUCTS AFFECTED: Netelligent 8500 Multi-Protocol Routers OPERATING SYSTEM: Cisco Technologies Software Version 1.26 and higher SYSTEM CONFIGURATION: N/A EFFECTIVE DATE: 17 April 1997 ELECTRONIC DISTRIBUTION ALLOWED: Yes SUPERSEDES: SP2384 (Version 1.1) DESCRIPTION: Use these files to upgrade Netelligent 8500 Multi-Protocol Routers to Netelligent 8500 Open Communications Platform Version 1.2. Contains the CISCO Technologies Software, drivers, firmware, and SASH (Standalone Shell) Utility, Version 1.12. IOS0411.EXE (dated 4-11-97) has the following problems fixed: 1. ipxDestNextHopDestNum returns incorrect type in SNMP requests. 2. IP route table has invalid or missing help information. 3. IGRP does not choose the best of 2 available links. 4. CFG command outputs garbage config,cli file if INIC is configured. 5. BOOTP Relay not functioning for DHCP clients and servers. 6. Stress test fails when running 1 or 2 PPP lines with compression. 7. PPP does not interoperate with the latest 11.2 version of Cisco 2500s. 8. If fragmentation is used at high speeds on Frame Relay, line goes down in 2-3 mins. 9. Problem loading Frame Relay on the 8500s if the compression module is not present. 10. If the compressed frame turns out to be larger than the maximum frame size compression resets occurs. 11. Frame Relay is talking to Cisco 2500 at T1 speed. After 2-3 minutes, PVCs become Inactive. 12. Backup feature of CCM is not working if backup line is on a different WNIC than the backed up line. 13. While using CCM's backup feature, the backed up line cannot be restored if the line is using compression. 14. CCM's DDR Feature fails to make call after its SUSPENDed if compression is enabled. The line uses PPP as the WAN protocol. 15. Modifier can change the login password even if he is not supposed to be able to do so. 16. Compaq router internal clocking not working. 17. RIP updates contain bad routes to connected inic. 18. PPP LCP magic number sent with value =0 (zero). 19. SnapShot with INIC does NOT resume with traffic. 20. IGRP not working between Cisco and Compaq over Frame Relay. 21. CFG command may hang router if config.cli already exists. 22. After DELCFG and reboot, previously downloaded configurations are ignored. 23. IPXWAN2 does not interoperate correctly with Cisco IOS 11.2. TLAN FIXES: 1. Refined the delay loop to complete auto-negotiation within the 1.5sec duration. 2. Modified the driver to send loop back frames to detect link status for both 10BaseT and 10Base2 connector types. 3. Added minimal support for SystemLog() to log changes in link status. 041497BX.BIN (dated 04-14-97) has the following fixes: SASH (Standalone Shell) Utility Version 1.12, 1. Unable to use any TFTP commands when a 0 is used as a single octet. 2. Backup command gives no error message when path (C:\) is given. 3. PASSWD command still in menu when it's no longer supported. Removed the PASSWD entry from the menu item's registry. 4. Check command says "successful" after errors encountered. 5. After a failed backup/restore/... SASH still allows user to boot. 6. Some commands still accept 0s before the slot#. HOW TO USE: 1. Download the SoftPaq to a sub-directory on your CNMS station within the CNMS software directory and change to that sub-directory. The file that is downloaded is SP3182.EXE. 2. From that drive and directory, execute the SoftPaq file: SP3182 [ENTER] The following files should be created: 041497BX.BIN IOS0411.EXE INSTALL.BAT SP3182.DOC README.TXT FLASHUPG.DOC ROMUPG.DOC 3. After the files are created, you may delete the downloaded file SP3182.EXE if you wish. 4. Refer to README.TXT for detailed instructions on installing and using the software. Copyright 1997, Compaq Computer Corporation. All rights reserved. Product names mentioned herein may be trademarks and/or registered trademarks of their respective companies