TITLE: iPAQ Pocket PC h5400 Series WLAN Firmware Update

VERSION: 100.5.39
DESCRIPTION: This SoftPaq contains the iPAQ Pocket PC h5400 Series WLAN Firmware Update

  IMPORTANT: For Pocket PC 2002, ROM update v1.11.xx must be installed first before the
             WLAN firmware update is installed.  DO NOT install the WLAN firmware update
             before installing ROM update v1.11.xx.

             This Softpaq will automatically launch the firmware update utility on your 
             host PC.  ActiveSync is required to install the update files and application
             on your iPAQ Pocket PC.  After the files finish copying to the iPAQ Pocket
             PC, the application will load and wait for the user to tap the “Start Update”
             button.  

	     Caution:  Do not turn the iPAQ off or remove AC power after taping the Start
             Update Button on the iPAQ Pocket PC.       


PURPOSE: Recommended Update
SOFTPAQ NUMBER: SP24567
SUPERSEDES: none
EFFECTIVE DATE: July 31, 2003
CATEGORY: ROMPaqs/BIOS and Firmware
SSM SUPPORTED: No

PRODUCT TYPE(S): Handhelds

PRODUCT MODEL(S): iPAQ h5400 Series Pocket PC
		  
OPERATING SYSTEM(S): Microsoft Pocket PC 2002
                     Microsoft Pocket PC 2003

LANGUAGE(S): Chinese Simplified

ENHANCEMENTS:
 - Firmware Update can run under Pocket PC 2002 or Pocket PC 2003
 - Adds LEAP authentication client support

FIXES:
 - Enables connect with a WLAN Access Point that supports both 802.11b and 802.11g

PREREQUISITES: 
 - For Pocket PC 2002, the ROM update v1.11.xx must be installed first before the
   WLAN firmware update is installed.  DO NOT install the WLAN firmware update
   before installing ROM update v1.11.xx.
 - Synchronization software such as Microsoft ActiveSync 3.5 or later

NOTES:
 - If the wireless LAN firmware update SoftPaq previously installed and upon 
   launching the Wireless LAN firmware update SoftPaq again, a window with the 
   selections 'Modify', 'Repair' and 'Remove' will appear. Select 'Remove' to 
   uninstall the previous installation and launch the Wireless LAN firmware update 
   SoftPaq again to reinstall. 

 
HOW TO USE:

       1. Download the SoftPaq to a directory on your hard drive.  The file
          downloaded is a self-extracting executable with a filename based on
          the SoftPaq Number above.

       2. Establish an Activesync connection between your iPAQ Pocket 
          PC and host PC.
       
       3. Execute the downloaded file and follow the on-screen instructions
          (This will unpack the WLAN Firmware update file to a directory on
          your host PC and automatically launch the installation wizard.)

       4. When ActiveSync Add/Remove Programs starts, select Yes to “Install
          … using the default application install directory.”  Select OK when
          the application downloading is complete.  (This will launch the 
          utility on your iPAQ Pocket PC.)

       5. Make sure your iPAQ Pocket PC is connected to AC power and tap the
          “Start Update” button on the iPAQ.  (The current and the new WLAN 
          firmware versions are displayed along with a progress bar.  The 
          update takes approximately 1 minute to complete.)  

       6. When the WLAN ROM Update completes, tap OK and perform a Normal Reset
          on the iPAQ, by pressing the reset button on the bottom of the iPAQ
          for 2 seconds, using the stylus.

       7. After successful completion of the firmware update, you may delete the
          following if you wish:
          a) The Firmware Update Utility from the iPAQ by going to
             State->Settings->System tab->Remove Program. Select 'hp WLAN Firmware
             Update' and tap the Remove button.
	  b) The self-extracting file downloaded to your host PC in step 1
     	  c) The directory created on your host PC in step 3



Copyright (c) 2003 Hewlett-Packard Development Company, L.P.