SOFTPAQ NUMBER: SP10967 PART NUMBER: 120216-297 FILE NAME: N/A TITLE: Diagnostics and Compaq Setup for Workstations VERSION: 10.37 Rev B for Diagnostics and 1.18 Rev A for Computer Setup for Workstations LANGUAGE: Japanese CATEGORY: Diagnostics-Setup DIVISION: Workstations PRODUCTS AFFECTED: Compaq Professional Workstation AP400 and AP500 OPERATING SYSTEM: N/A SYSTEM CONFIGURATION: N/A PREREQUISITES: N/A EFFECTIVE DATE: July 19, 1999 ELECTRONIC DISTRIBUTION ALLOWED: Yes SOFTPAQ UTILITY VERSION: 2.x SUPERSEDES: SP10176 DESCRIPTION: Creates four diskettes: - Two diskette for Personal Computer Diagnostics - Two diskettes for Computer Setup for Workstations PC Diagnostics and Computer Setup for Workstations are both pre-installed on the Diagnostics Partition. The diskettes in this SoftPaq should be used to update these utilities on the Diagnostics Partition. They can also be used to restore the Diagnostics Partition if it has been destroyed. Both utilities can be run by pressing F10 when the cursor moves to the upper right corner of the screen during power-up or reboot. Or they can be run directly from these diskettes. Personal Computer Diagnostics contains programs that can test and inspect the state of Compaq Professional Workstations and their devices. Computer Setup for Workstations allows the user to configure security and power management settings as well as system resources (DMA, IRQ, I/O Ports, and Memory). ENHANCEMENT/FIXES: History: - Fixed: Can not re-enable SCSI controller after disabling on Workstations. - Fixed: Corruped Japanese word "Resource" in ISA section. - Fixed: Corruped Japanese word "enable/disable" in Storage section. - Fixed: Can not change PCI board IRQ configration. - Fixed: "Set Defaults & Exit" fails to restore parameters for SCSI Controller Order. - Fixed: Misdetects the Pentium 2 450 MHz CPU as a 450 MHz Intel Pentium Pro. - Fixed: Text corruption issue on F10 partition when jumping to Setup on a machine with an Oxygen GVX1 graphics card installed. - Fixed: Inspect hang during NIC ID on an AP200 with an Oxygen GVX1 installed. - Fixed: Locks system with a Mylex Tomcat after running Setup. HOW TO USE: 1. Obtain four (4) formatted 1.44 MB diskettes. 2. Download the SoftPaq to a directory on your hard drive and change to that directory. The file that is downloaded is an executable with a filename based on the SoftPaq Number above. 3. From that drive and directory, execute the SoftPaq file. You will be prompted when to place each of the three formatted 1.44 MB diskettes into a diskette drive to create the diskettes. Label them as follows, using the Version numbers given above: First Diskette -- Personal Computer Diagnostics (TEST) Second Diskette -- Personal Computer Diagnostics (INSPECT) Third Diskette -- Computer Setup for Workstations (Disk 1 of 2) Fourth Diskette -- Computer Setup for Workstations (Disk 2 of 2) 4. After the diskettes are created, you may delete the SoftPaq file downloaded in step 2 if you wish. 5. Power down your computer, place the Personal Computer Diagnostics diskette in Drive A:, and power up your computer. a. To create or upgrade the Diagnostics Partition, select Manage Diagnostics Partition from the Compaq Utilities menu, then select either Create or Upgrade Diagnostics Partition. You will be prompted on when to insert the two Computer Setup for Workstations diskettes. b. To run TEST or INSPECT from the diskette without upgrading the Diagnostics Partition, select either TEST or INSPECT from the Compaq Utilities menu. 6. To run Computer Setup from diskette without creating or upgrading the Diagnostics Partition, boot from the Compaq Setup for Workstations diskette number 1, and select Run Setup from the main menu. Copyright 1999, Compaq Computer Corporation. All rights reserved. Product names mentioned herein may be trademarks and/or registered trademarks of their respective companies