C O M P A Q (R)  C O M P U T E R  C O R P O R A T I O N

                         Compaq Support Paq for
                         Microsoft Windows 2000
                 

1.  INTRODUCTION

This file contains information regarding use of the Compaq Support Paq for
Microsoft Windows 2000.  The following information is provided:

    Support Paq Installation
    Component Usage
    Log File Usage

2.  SUPPORT PAQ INSTALLATION

The primary method for installing the Support Paq is to run the SETUP.EXE
program included with the Support Paq.  By default, all software is selected for
installation.  In most circumstances, this default selection should not be
altered, and installation is as simple as pressing the "Install>" button.  Even
when selected, only software that is appropriate for the system it is being run
on will actually be installed.  Press the "Install>" button to proceed with the
installation.  After installation of the appropriate software the utility will
display its results, including indication of software successfully installed,
software not needed for the current system configuration and any installation
failures.

A BPxxxxxx.CMD file is also provided with the Support Paq for use in installing
the Support Paq from a command prompt without user interaction.  As with the
SETUP.EXE program, all software appropriate for the system it is being run on
will be installed.

The Compaq Support Paq for Microsoft Windows 2000 contains numerous files.  All
files must be present in the same directory as the SETUP.EXE program or in order
for the Support Paq to be installed properly.

3.  COMPONENT PACKAGE USAGE

In addition to the SETUP.EXE program mentioned above, the Support Paq contains
individual .EXE files corresponding to the various software packages that make
up the Support Paq.  If necessary, these software packages can be installed
individually or their contents extracted to a floppy diskette for use during OS
installation.

To install an individual component package just run the appropriate CPxxxxx.EXE
file and chose the "Install" button.

To extract the contents of a component package to diskette run the appropriate
CPxxxxx.EXE file, then chose the "Extract" button instead of the "Install"
button.

The following table specifies the Compaq software contained within and installed
by each component package:

CP000609.EXE          Compaq Advanced System Management Driver
CP000610.EXE          Compaq System Management Controller Driver
CP000611.EXE          Compaq Integrated System Management Controller Driver
CP000664.EXE          Compaq Drive Array Driver
CP000624.EXE          Compaq Smart Array-2 Controllers Driver
CP000612.EXE          Compaq 32-Bit SCSI Controller Driver
CP000613.EXE	      Compaq Smart Array 5x Adapter Support
CP000670.EXE          Compaq 64-Bit/66-Mhz Wide Ultra3 SCSI Controller Driver
CP000625.EXE	      Compaq StorageWorks Fibre Channel Host Bus Adapter Drive
CP000626.EXE	      Compaq CMD 0649 Ultra DMA IDE Controller Driver for Windows 2000
CP000672.EXE	      Compaq Integrated Ultra ATA-100 Dual Channel Driver
CP000614.EXE          Compaq ProLiant Storage System Support
CP000627.EXE          Compaq Drive Array Notification
CP000731.EXE          Compaq NetFlex/Netelligent Adapter Driver
CP000732.EXE          Compaq Ethernet or Fast Ethernet NIC NT Driver
CP000733.EXE          Compaq Gigabit Ethernet NIC NT Driver
CP000734.EXE	      Compaq Network Teaming and Configuration
CP000615.EXE          Compaq PCI Hot Plug Controller Driver
CP000665.EXE          Compaq Integrated Management Dispay Utility
CP000666.EXE          Compaq Integrated Management Log Viewer
CP000667.EXE          Compaq Power Supply Viewer
CP000668.EXE          Compaq Power Down Manager
CP000616.EXE          Compaq Enhanced Integrated Management Display Service
CP000669.EXE          Compaq Remote Monitor Service
CP000628.EXE          Compaq Array Configuration Utility
CP000618.EXE	      Compaq Remote Insight Board Driver
CP000617.EXE          Compaq ATI RAGE IIC Video Controller Support
CP000671.EXE          Compaq Array Redundancy Software
CP000619.EXE	      Compaq Foundation Agents
CP000620.EXE	      Compaq Server Agents
CP000621.EXE	      Compaq Storage Agents
CP000622.EXE	      Compaq NIC Agents
CP000623.EXE	      Compaq Survey Utility

4.  LOG FILE USAGE

Progress and results of the installation of all software included in the Support
Paq is logged to the file %SystemDrive%\cpqsystem\log\cpqsetup.log.  This file can be
viewed with any text editor.  Information for subsequent installations is
appended to this log file, providing a chronological history of installation
activity for all software installed by the Support Paq installation utilities.

----------------------------------------------------------------
Copyright 2001, Compaq Computer Corporation. All rights reserved.

Product names mentioned herein may be trademarks and/or registered
trademarks of their respective companies.