C O M P A Q (R)  C O M P U T E R  C O R P O R A T I O N

                         Compaq Support Paq for
                         Microsoft Windows NT 4
                 

1.  INTRODUCTION

This file contains information regarding use of the Compaq Support Paq for
Microsoft Windows NT 4.  The following information is provided:

    Support Paq Installation
    Component Usage
    Log File Usage


2.  SUPPORT PAQ INSTALLATION

The primary method for installing the Support Paq is to run the SETUP.EXE
program included with the Support Paq.  By default, all software is selected for
installation.  In most circumstances, this default selection should not be
altered, and installation is as simple as pressing the "Install" button.  Even
when selected, only software that is appropriate for the system it is being run
on will actually be installed.  Press the "Install" button to proceed with the
installation.  After installation of the appropriate software the utility will
display its results, including indication of software successfully installed,
software not needed for the current system configuration and any installation
failures.  For more information on the usage of SETUP.EXE, refer to the help
file (SETUP.HLP).

A BPxxxxxx.CMD file is also provided with the Support Paq for use in installing
the Support Paq from a command prompt without user interaction.  As with the
SETUP.EXE program, all software appropriate for the system it is being run on
will be installed.

The Compaq Support Paq for Microsoft Windows NT 4 contains numerous files.  All
files must be present in the same directory as the SETUP.EXE program or in order
for the Support Paq to be installed properly.

A console version of the setup application (SETUPC.EXE) is also provided as a
way to script installations of the Support Paq or components.  For more
information on its usage, refer to the help file (SETUPC.HLP).


3.  COMPONENT USAGE

In addition to the SETUP.EXE program mentioned above, the Support Paq contains
individual .EXE files corresponding to the various components that make
up the Support Paq.  If necessary, these components can be installed
individually or their contents extracted to a floppy diskette for use during OS
installation.

To install an individual component just run the appropriate CPxxxxx.EXE file
and chose the "Install" button.

To extract the contents of a component to diskette run the appropriate
CPxxxxx.EXE file, then chose the "Extract" button instead of the "Install"
button.

The following table specifies the Compaq software contained within and installed
by each component:

CP000317.EXE     Compaq System Management Driver
CP000318.EXE     Compaq Smart Array 53xx Adapter Support
CP000304.EXE     Compaq Smart Array-2 Controllers Driver
CP000303.EXE     Compaq Drive Array Driver
CP000302.EXE     Compaq 32-Bit SCSI Controller
CP000312.EXE     Compaq StorageWorks Fibre Channel Host Bus Adapter Driver
CP000452.EXE     Compaq CMD 0649 Ultra DMA IDE Controller Driver for NT 4.0
CP000315.EXE     Compaq Proliant Storage System Support
CP000316.EXE     Compaq Remote Insight Board for Wide Area Networks
CP000300.EXE     Compaq 64-Bit/66Mhx Wide Ultra3 Controller Driver
CP000314.EXE     Compaq Remote Insight Board Driver
CP000310.EXE     Compaq Remote Monitor Service
CP000305.EXE     Compaq Integrated Management Display Utility
CP000306.EXE     Compaq Integrated Management Log Viewer
CP000308.EXE     Compaq Power Supply Viewer
CP000307.EXE     Compaq Hot Plug Controller Driver
CP000313.EXE     Compaq Array Redundancy Software
CP000309.EXE     Compaq Power Down Manager
CP000311.EXE     Compaq Enhanced Integrated Management Display Service
CP000501.EXE     Compaq ATI RAGE IIC Graphics Adapter Driver
CP000502.EXE     Compaq ATI RAGE XL Graphics Adapter Driver
CP000358.EXE     Compaq Array Configuration Utility
CP000357.EXE     Compaq NetFlex/Netelligent Adapter Driver
CP000356.EXE     Compaq Ethernet/Fast Ethernet or Gigabit NIC Driver
CP000231.EXE     Compaq Foundation Agent
CP000583.EXE     Compaq Server Agent
CP000234.EXE     Compaq Storage Agent
CP000233.EXE     Compaq NIC Agent
CP000235.EXE     Compaq Survey Utility

4.  LOG FILE USAGE

Progress and results of the installation of all software included in the Support
Paq is logged to the file %SystemDrive%\cpqsystem\log\cpqsetup.log.  This file can be
viewed with any text editor.  Information for subsequent installations is
appended to this log file, providing a chronological history of installation
activity for all software installed by the Support Paq installation utilities.

----------------------------------------------------------------
Copyright 2000, Compaq Computer Corporation. All rights reserved.

Product names mentioned herein may be trademarks and/or registered
trademarks of their respective companies.