[SunHELP] QFE hme

[George Munk]

David,

The Quad Fast Ethernet SBUS card has a rev 1.0 and rev 2.0. In the 1.0 rev =
(part number X1042A, 501-4302 on the card), the interfaces are "hme". On =
your system, hme0 should be the onboard interface and hme1, hme2, hme3 and =
hme4 should be the four interfaces of the quad card. Configure as you =
normally would using those names.


Regards,
George Munk


>>> henden at h8.dion.ne.jp 09/21/01 06:34PM >>>
Hello there.
I would like to ask for your help, if you don't mind.

Well, I have an Ultra2. I put a QFE card in it and then installed
Solaris 8 1/001
This is what I see from prtdiag -v
System clock frequency: 99 MHz
Memory size: 1024 Megabytes

=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
 CPUs =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D

                    Run   Ecache   CPU    CPU
Brd  CPU   Module   MHz     MB    Impl.   Mask
---  ---  -------  -----  ------  ------  ----
 0     0     0      296     2.0   US-II    1.1
 0     1     1      296     2.0   US-II    1.1


=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
 IO Cards =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D

     Bus   Freq
Brd  Type  MHz   Slot  Name                              Model
---  ----  ----  ----  --------------------------------
----------------------
 0   SBus   25     1   QLGC,isp/sd (block)               QLGC,ISP1000
 0   SBus   25     3   SUNW,hme                          SUNW,sbus-qfe
 0   SBus   25     3   SUNW,hme                          SUNW,sbus-qfe
 0   SBus   25     3   SUNW,hme                          SUNW,sbus-qfe
 0   SBus   25     3   SUNW,hme                          SUNW,sbus-qfe
 0   SBus   25    14   SUNW,fas/sd (block)
 0   SBus   25    14   SUNW,hme
 0   SBus   25    14   SUNW,bpp
 0   UPA    99    30   FFB, Double Buffered              SUNW,501-3129

No failures found in System
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D

=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
 HW Revisions =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D

ASIC Revisions:
---------------
SBus: sbus Rev 1
FEPS: SUNW,hme Rev 22
FEPS: SUNW,hme Rev 22
FEPS: SUNW,hme Rev 22
FEPS: SUNW,hme Rev 22
FEPS: SUNW,hme Rev 22

FFB Hardware Configuration:
-----------------------------------
        Board rev: 3
        FBC version: 0x1
        DAC: Brooktree 9068, version 4
        3DRAM: Mitsubishi 1309, version 3

System PROM revisions:
----------------------
  OBP 3.25.0 1999/12/03 11:35   POST 3.3.8 1998/11/16 01:42

But when I try to set up the card as per maunal, i.e.,  grep qfe
/etc/path_to_inst
I get nothing,.
Now, when I do a grep hme /etc/path_to_inst I get the following:

"/sbus at 1f,0/SUNW,hme at e,8c00000" 0 "hme"
"/sbus at 1f,0/SUNW,hme at 3,8c30000" 4 "hme"
"/sbus at 1f,0/SUNW,hme at 3,8c20000" 3 "hme"
"/sbus at 1f,0/SUNW,hme at 3,8c10000" 2 "hme"
"/sbus at 1f,0/SUNW,hme at 3,8c00000" 1 "hme"

So, what I would like to know, is why this machine will not let me set
up QFE.
I hope you can help me out.

Thanks in advance.

David

_______________________________________________
SunHELP maillist  -  SunHELP at sunhelp.org=20
http://www.sunhelp.org/mailman/listinfo/sunhelp