[SunRescue] argh! cisco firmware update failed

[Gil Young]

only other link I found was a generic one:

http://www.cisco.com/univercd/cc/td/doc/product/fhubs/fh400/fh400icg/fh4trbl
.htm

Best wishes, I have done the same thing before on a corporate firewall once
(a morningstar router), with no backup firmware!  My mentor and I had to
drag a Wellfleet router out and config the corp firewall from scratch (and
mostly memory).  Those were the days :).

Gil Young
Call Sign: KG4KVX
-----BEGIN GEEK CODE BLOCK-----
Version: 3.12
GIT d+ s+:+ a C++ US++++ P+ L+ E--- W++ N+ o K+ w O- M+ V
PS PE+ Y+ PGP t+ 5 X+ R tv b+ DI+ D++ G e++ h--- r+++ y+++
------END GEEK CODE BLOCK------

----- Original Message -----
From: Gil Young <gjyoung at cfl.rr.com>
To: <rescue at sunhelp.org>
Sent: Thursday, May 31, 2001 2:22 AM
Subject: Re: [SunRescue] argh! cisco firmware update failed


> not sure if this helps any:
>
>
http://www.cisco.com/univercd/cc/td/doc/product/fhubs/fh300icg/rptrtrbl.htm#
> xtocid105073
>
>
http://www.cisco.com/univercd/cc/td/doc/product/fhubs/fh216t/rpt2trbl.htm#xt
> ocid57097
>
> Still looking...
> Gil Young
> Call Sign: KG4KVX
> -----BEGIN GEEK CODE BLOCK-----
> Version: 3.12
> GIT d+ s+:+ a C++ US++++ P+ L+ E--- W++ N+ o K+ w O- M+ V
> PS PE+ Y+ PGP t+ 5 X+ R tv b+ DI+ D++ G e++ h--- r+++ y+++
> ------END GEEK CODE BLOCK------
>
> ----- Original Message -----
> From: Bill Bradford <mrbill at mrbill.net>
> To: <geeks at mrbill.net>; <rescue at mrbill.net>
> Sent: Thursday, May 31, 2001 1:47 AM
> Subject: [SunRescue] argh! cisco firmware update failed
>
>
> > Anybody know if there's a way to re-load a firmware image
> > into a Cisco 1516M 16-port managed hub (aka HP J3188A) if the
> > update (from the original 1.00 version) failed?  When it went
> > to TFTP the update, it asked for the IP address of the TFTP server, the
> > filename to download, then hung, a few seconds later killed
> > my telnet session.  It was still passing traffic, *until*
> > I power-cycled it; now I just get a "FAIL" light and it doesent
> > finish its self-test.
> >
> > A little too late, I found this:
> >
> >
>
(http://www.cisco.com/univercd/cc/td/doc/product/10bthubs/hp10base/ol015901.
> htm)
> > Problems Resolved in Firmware Release A.01.03
> > ...
> > The Trivial File Transfer Protocol (TFTP) command is now in the normal
> command
> > set. This change resolves the internal conflict between TFTP and Telnet
> that
> > caused TFTP to hang during firmware download, thus corrupting the
firmware
> in
> > Flash memory.
> >
> >
> > I'm hoping there's some way I can upload the firmware through a serial
> > console connection at work tomorrow (gotta get a DB9 serial cable and
> > nullmodem adapter)...
> >
> > Would suck to have gotten this in after waiting more than a week for it,
> > setup MRTG to monitor it, etc, and then have it ruined by a bad firmware
> > update. 8-(  I was *so* happy to finally have Cisco hardware running my
> > network here at home.
> >
> > bill
> >
> > --
> > Bill Bradford
> > mrbill at mrbill.net
> > Austin, TX
> > _______________________________________________
> > rescue maillist  -  rescue at sunhelp.org
> > http://www.sunhelp.org/mailman/listinfo/rescue
>
> _______________________________________________
> rescue maillist  -  rescue at sunhelp.org
> http://www.sunhelp.org/mailman/listinfo/rescue