Archive-name: sun-hdwr-ref/part6
Posting-Frequency: as revised
Version: $Id: part6,v 1.3 1995/08/06 23:08:20 jwbirdsa Exp $
                       THE SUN HARDWARE REFERENCE
                     compiled by James W. Birdsall
                        (jwbirdsa@picarefy.com)

                                PART VI
                                =======
                               APPENDICES


APPENDICES
==========

    Cardcage configuration tables
    -----------------------------

   How to use the cardcage configuration tables:

   Boards are listed in order of priority, from top to bottom. If two
boards would prefer to be installed in the same slot, whichever board is
toward the top of the table wins, unless the lower board cannot be
installed in any other slot.

   Many boards can be installed in any of several slots. The most
desirable slot is indicated with "A", the second most desirable with
"B", and so on.

   Note that many boards are unfortunately not listed. Also note that
these are only the official Sun-recommended board orders (except where
specifically noted); in many cases boards will work in other slots.
Consult the listings for the individual boards. Note that memory boards
usually need to be in the recommended positions, since there is usually
a special memory bus in the backplane to which all memory boards must
connect.

   Note that the configurations below represent the cardcage tables
dated 6/8/88. Sometimes there are major changes in preferred slots
between cardcage table revisions. If you think you need an older version
(5/13/87 is available), send me email (remind me that 5/13/87 is in
revision 1.1 of part 7, please).

MULTIBUS

    2/120

        board                   slot:   1  2  3  4  5  6  7  8  9

        CPU 501-1007/1051               A  -  -  -  -  -  -  -  -
        1st memory 501-1013/1048        -  A  -  -  -  -  -  -  -
        2nd memory 501-1013/1048        -  -  A  -  -  -  -  -  -
        3rd memory 501-1013/1048        -  -  -  A  -  -  -  -  -
        4th memory 501-1013/1048        -  -  -  -  A  -  -  -  -
        5th memory 501-1013/1048 * #    -  -  -  -  -  A  -  -  -
        ALM-8 USART 370-1046 *          -  -  -  -  -  A  -  -  -
        ALM-8 controller 370-1047       -  -  -  -  -  -  A  -  -
        mono framebuffer 501-1003/1052* -  -  -  -  B  A  -  -  -
        1st SCP 370-1049                -  -  -  -  -  -  A  B  -
        2nd SCP 370-1049                -  -  -  -  -  -  -  A  B
        SCSI/serial 501-1006            -  -  -  B  A  -  C  D  E
        1st Ethernet 501-1004/370-0288  -  -  A  B  C  -  D  E  F
        2nd Ethernet 501-1004/370-0288  -  -  -  A  B  -  C  D  E
        1st 1/2" tape **                -  -  -  -  -  -  A  B  C
        2nd 1/2" tape **                -  -  -  -  -  -  -  A  B
        1st Xylogics 450 SMD 370-1012   -  -  -  -  -  -  A  B  C
        2nd Xylogics 450 SMD 370-1012   -  -  -  -  -  -  -  A  B
        Sky FFP 370-1021                -  -  -  -  -  -  A  B  C
        Color processor 501-0461        -  -  F  E  D  -  C  B  A

        *  In older backplanes (501-1090), slot 6 must be occupied by
           either a monochrome framebuffer board or a P2 terminator
           board. Newer backplanes do not need external P2 termination.

        ** Either the Computer Products Corporation TAPEMASTER
           (370-0502?/0167?) or the Xylogics 472 1/2" 6250bpi tape
           controller (370-0502?).

        #  Memory boards have been confirmed to work in slot six of a
           2/120 with a newer backplane.

    2/170

        board           slot:   1  2  3  4  5  6  7  8  9 10 11 12 13 14 15
        CPU 501-1007/1051       A  -  -  -  -  -  -  -  -  -  -  -  -  -  -
        1st mem 501-1013/1048   -  A  -  -  -  -  -  -  -  -  -  -  -  -  -
        2nd mem 501-1013/1048   -  -  A  -  -  -  -  -  -  -  -  -  -  -  -
        3rd mem 501-1013/1048   -  -  -  A  -  -  -  -  -  -  -  -  -  -  -
        4th mem 501-1013/1048   -  -  -  -  A  -  -  -  -  -  -  -  -  -  -
        5th mem 501-1013/1048 # -  -  -  -  -  A  -  -  -  -  -  -  -  -  -
        mono fb 501-1003/1052   -  -  -  -  -  A  -  -  -  -  -  -  -  -  -
        1st SCP 370-1049        -  -  -  -  -  -  A  -  -  -  -  -  -  -  -
        2nd SCP 370-1049        -  -  -  -  -  -  -  A  -  -  -  -  -  -  -
        SCSI/serial 501-1006    -  -  -  B  A  -  C  D  E  -  -  -  -  -  -
        1st Ethernet *          -  -  A  B  C  -  D  E  F  G  -  -  -  -  -
        2nd Ethernet *          -  -  -  A  B  -  C  D  E  F  G  -  -  -  -
        1st 1/2" tape **        -  -  -  -  -  -  A  B  C  D  E  F  -  -  -
        2nd 1/2" tape **        -  -  -  -  -  -  -  A  B  C  D  E  F  -  -
        1st SMD 370-1012 ##     -  -  -  -  -  -  A  B  C  D  E  F  G  H  -
        2nd SMD 370-1012 ##     -  -  -  -  -  -  -  A  B  C  D  E  F  G  H
        Sky FFP 370-1021        -  -  -  -  -  -  A  B  C  D  E  F  G  H  I
        Color proc 501-0461     -  -  -  -  -  -  -  -  -  -  -  -  -  -  A
        ALM-14 ctrl 370-1047    -  -  -  -  -  -  A  B  C  D  E  F  G  H  I
        ALM-14 USART 370-1048   -  -  -  -  -  -  -  A  B  C  D  E  F  G  H

        *  Either the Sun 501-1004 or the 3COM 370-0288.

        ** Either the Computer Products Corporation TAPEMASTER
           (370-0502?/0167?) or the Xylogics 472 1/2" 6250bpi tape
           controller (370-0502?).

        #  Memory boards have been confirmed to work in slot six of a
           2/120, and should work in a 2/170.

        ## Xylogics 450.


VME

   Note that VME cards frequently have "springfingers" on their rear
edges, metal strips that are installed between the edge of the PC board
and the outer panel to reduce RFI emissions, with serrated metal
"fingers" protruding from either side of the strip. If a board with
springfingers is installed next to a board without springfingers, there
must be a plastic insulator shield over the fingers on the side toward
the fingerless board, to prevent possible shorting of component leads to
the springfingers.

   VME cardcages (except for the 2/50 and the 3/75) also have jumpers on
the backplane itself, one set per slot, which must be set appropriately
for the board in the corresponding slot. These jumpers are marked Px0y,
where x is the number of the slot and y is the number of the jumper.
Jumpers Px00, Px01, and Px02 must always be installed in normal use.
Jumpers Px03 (BG3) and Px04 (IACK) are installed according to the board
in the slot, and always installed for empty slots. Note that 2/130 and
2/160 systems shipped before 11/1/85 did not have these jumpers
installed by default. The highest-numbered slot is usually (always?)
missing Px04. Note that the jumpers are usually (always?) on the
opposite side of the backplane from the VME connectors and are usually
(always?) accessed via a panel in the front of the machine.

    2/50

        board                   slot:   1  2

        CPU 501-1141/1142/1143 *        A  -
        memory/SCSI/FFP **              -  A

        *  501-1141     1M CPU
           501-1142     2M CPU
           501-1143     4M CPU

        ** 501-1020     1M memory
           501-1046     2M memory
           501-1067     3M memory
           501-1047     4M memory
           501-1079     0M memory
           501-1147     501-1079 0M memory + 501-1045 "Sun-2" SCSI
           501-1148     501-1079 0M memory + 370-1029 Sky FFP

           The 501-1045 "Sun-2" SCSI and 370-1029 Sky FFP may also be
           piggybacked on the 1-4M memory boards, but there is no
           separate part number for these combinations.

    2/130, 2/160

        board           slot:   1  2  3  4& 5  6  7  8  9 10 11 12 Px03 Px04
        CPU 501-1144/1145/1146* A  -  -  -  -  -  -  -  -  -  -  -  UN   UN
        memory **               -  A  -  -  -  -  -  -  -  -  -  -  JU   JU
        GP 501-1055             -  -  A  -  -  -  -  -  -  -  -  -  UN   UN
        GB 501-1058             -  -  -  A  -  -  -  -  -  -  -  -  JU   JU
        color fb 501-1014/1116  -  -  -  -  A  -  -  -  -  -  -  -  JU   UN
        ALM-1 501-1157 &&       -  -  -  -  -  -  -  -  -  -  -  A  UN   N/A
        SCSI 501-1149           -  -  -  -  -  A  -  -  -  -  -  -  UN   UN
        1st SCP 501-1158 &      -  -  A  B  C  D  E  -  -  -  -  -  UN   UN
        2nd SCP 501-1158 &      -  -  -  A  B  C  D  E  -  -  -  -  UN   UN
        1st MAPKIT 501-1202 & # -  -  A  A  C  C  E  E  G  G  -  -  UN   UN
                                -  -  -  B  B  D  D  F  F  -  -  -
        2nd MAPKIT 501-1202 & # -  -  -  -  A  A  C  C  E  E  G  G  UN   UN
                                -  -  -  -  -  B  B  D  D  F  F  -
        1st 1/2" tape ctrl ## @ -  -  A  B  C  D  E  F  G  H  I  J  UN   UN
        2nd 1/2" tape ctrl ## @ -  -  -  A  B  C  D  E  F  G  H  I  UN   UN
        1st SMD ctrl @ @@       -  -  A  B  C  D  E  F  G  H  I  J  UN   UN
        2nd SMD ctrl @ @@       -  -  -  A  B  C  D  E  F  G  H  I  UN   UN
        Sky FFP 501-1151        -  -  -  -  A  B  C  D  E  F  G  H  JU   JU
        2nd Ethernet 501-1153   -  -  A  B  C  D  E  F  G  H  I  J  UN   UN
        1st IPC 501-1125        -  -  -  -  -  -  -  -  -  B  -  A  JU   UN
        2nd IPC 501-1125        -  -  -  -  -  -  -  -  B  -  A  -  JU   UN
        3rd IPC 501-1125        -  -  -  -  -  -  -  B  -  A  -  -  JU   UN
        4th IPC 501-1125        -  -  -  -  -  -  B  -  A  -  -  -  JU   UN

        *  501-1144     1M CPU
           501-1145     2M CPU
           501-1146     4M CPU

        ** 501-1070     1M memory
           501-1096     2M memory
           501-1071     3M memory
           501-1097     4M memory

        &  Slot 4 cannot be populated with other than a 501-1058
           graphics buffer (GB) when a 501-1055 graphics processor (GP)
           is in slot 3, unless the Multibus-VME converter (used on the
           GP?) is 501-1054-04 rev A or later. Otherwise, there will be
           contention on the "GP/GB bus".

        && The 501-1157 ALM-1 covers two slots (11 and 12) but only
           connects electrically to 12. Hence, treat slot 11 as empty
           (i.e. jump both P1103 and P1104).

        #  The 501-1202 MAPKIT covers two slots but only connects
           electrically to the lower-numbered slot. Hence, treat the
           higher-numbered slot as empty (i.e. jump both Px03 and Px04).

        ## 501-1155     Xylogics 472 1/2" tape controller (6250bpi)
           501-1156     CPC 1/2" tape controller (1600bpi)

        @  Do not place either a 1/2" tape controller or an SMD
           controller in a slot to the left of the SCSI board. Doing so
           may adversely impact the functionality of the SCSI subsystem.

        @@ 501-1154     Xylogics 450 SMD controller in Multibus-VME converter
           501-1166     Xylogics 451 SMD controller in Multibus-VME converter

    3/75

        board                   slot:   1  2

        CPU 501-1163/1164 *             A  -
        memory/SCSI **                  -  A

        *  501-1163     2M CPU
           501-1164     4M CPU

        ** 501-1111     2M memory
           501-1122     4M memory
           501-1121     0M memory
           501-1172     501-1121 0M memory + 501-1045 "Sun-2" SCSI

           The 501-1045 "Sun-2" SCSI may also be piggybacked on the 2M
           or 4M memory boards, but there is no separate part number for
           these combinations.

           The 501-1236 "Sun-3" SCSI had not been qualified for use in
           the 3/75 as of June 1988.

    3/110

        board           slot:   1  2* 3* Px03 Px04
        CPU 501-1134/1209       A  -  -   UN   UN
        1st 4M RAM 501-1132     -  A  -   JU   JU
        2nd 4M RAM 501-1132     -  -  A   JU   JU
        FPA 501-1105            -  A  B   JU   JU
        1st SCP 501-1158 *      -  A  B   UN   UN
        2nd SCP 501-1158 *      -  -  A   UN   UN
        1st MCP 501-1221 !      -  A  B   UN   UN
        2nd MCP 501-1221 !      -  -  A   UN   UN
        1st ALM-2 501-1203 !    -  A  B   UN   UN
        2nd ALM-2 501-1203 !    -  -  A   UN   UN
        MAPKIT 501-1202 **      -  A  A   UN   UN
        SCSI 501-1138/1217      -  B  A   UN   UN
        2nd Ethernet 501-1153 * -  B  A   UN   UN
        1st IPC 501-1125        -  B  A   JU   UN
        2nd IPC 501-1125        -  A  -   JU   UN

        *  If you wish to install a Multibus-VME converter-based board
           in slots 2 or 3, you just use converters 501-1054-04 rev A
           or later to avoid contention on the P2 memory bus.

        ** The 501-1202 MAPKIT covers slots 2 and 3 but only connects
           electrically to slot 2. Hence, treat slot 3 as empty (i.e.
           jump both P303 and P304).

        !  See "Important Note about ALM and MCP products", below.

    3/140

        board           slot:   1  2* 3* Px03 Px04
        CPU ##                  A  -  -   UN   UN
        1st memory **           -  A  -   JU   JU
        2nd memory **           -  -  A   JU   JU
        FPA 501-1105            -  A  B   JU   JU
        1st SCP 501-1158 *      -  A  B   UN   UN
        2nd SCP 501-1158 *      -  -  A   UN   UN
        1st MCP 501-1221 !      -  A  B   UN   UN
        2nd MCP 501-1221 !      -  -  A   UN   UN
        1st ALM-2 501-1203 !    -  A  B   UN   UN
        2nd ALM-2 501-1203 !    -  -  A   UN   UN
        MAPKIT 501-1202 #       -  A  A   UN   UN
        SCSI 501-1138/1217      -  B  A   UN   UN
        2nd Ethernet 501-1153 * -  B  A   UN   UN
        1st IPC 501-1125        -  B  A   JU   UN
        2nd IPC 501-1125        -  A  -   JU   UN

        *  If you wish to install a Multibus-VME converter-based board
           in slots 2 or 3, you just use converters 501-1054-04 rev A
           or later to avoid contention on the P2 memory bus.

        ** 501-1131     2M memory
           501-1132     4M memory

        #  The 501-1202 MAPKIT covers slots 2 and 3 but only connects
           electrically to slot 2. Hence, treat slot 3 as empty (i.e.
           jump both P303 and P304).

        ## 501-1163     2M CPU
           501-1164     4M CPU
           501-1208     4M CPU

        !  See "Important Note about ALM and MCP products", below.

    3/150

        board           slot:   1  2# 3# 4# 5# 6# Px03 Px04
        CPU *                   A  -  -  -  -  -  UN   UN
        1st 4M memory 501-1132  -  A  -  -  -  -  JU   JU
        FPA 501-1105            -  -  -  A  -  -  JU   JU
        2nd 4M memory 501-1132  -  -  A  -  -  -  JU   JU
        3rd 4M memory 501-1132  -  -  -  A  -  -  JU   JU
        GP/GP+/GP2 ** % %%      -  -  -  -  A  -  UN   UN
        GB 501-1058 # %         -  -  -  -  -  A  JU   JU
        ALM-1 501-1157 # ## !   -  -  -  -  -  A  UN   N/A
        1st SCP 501-1158 #      -  A  B  C  D  E  UN   UN
        2nd SCP 501-1158 #      -  -  A  B  C  D  UN   UN
        1st MCP 501-1221 !      -  A  B  C  D  E  UN   UN
        2nd MCP 501-1221 !      -  -  A  B  C  D  UN   UN
        3rd MCP 501-1221 !      -  -  -  A  B  C  UN   UN
        4th MCP 501-1221 !      -  -  -  -  A  B  UN   UN
        1st ALM-2 501-1203 !    -  A  B  C  D  E  UN   UN
        2nd ALM-2 501-1203 !    -  -  A  B  C  D  UN   UN
        3rd ALM-2 501-1203 !    -  -  -  A  B  C  UN   UN
        4th ALM-2 501-1203 !    -  -  -  -  A  B  UN   UN
        SunLink Channel Adpt @  -  A  A  C  C  -  UN   UN
                                -  -  B  B  D  D
        1st MAPKIT 501-1202 @@  -  A  A  C  C  -  UN   UN
                                -  -  B  B  D  D
        2nd MAPKIT 501-1202 @@  -  -  -  A  A  -  UN   UN
                                -  -  -  -  B  B
        SCSI 501-1138/1217      -  A  B  C  D  E  UN   UN
        Sun-2 clr 501-1014 & %  -  A  B  C  D  E  JU   UN
        cg3 color 501-1116 & %  -  A  B  C  D  E  JU   UN
        cg5 color 501-1267 & $  -  A  B  C  D  E  JU   UN w/o GP or GP+
         "    "    "   "   && $ -  A  B  C  -  -  JU   UN with GP or GP+
         "    "    "   "   %%   -  -  -  -  -  A  JU   UN with GP2
        2nd Ethernet 501-1153 # -  A  B  C  D  E  UN   UN
        1st IPC 501-1125        -  A  B  C  D  E  JU   UN
        2nd IPC 501-1125        -  -  A  B  C  D  JU   UN

        *  501-1163     2M CPU
           501-1164     4M CPU
           501-1208     4M CPU

        ** 501-1055     Graphics Processor
           501-1139     Graphics Processor Plus
           501-1268     Graphics Processor 2

        &  The 501-1014 Sun-2 color framebuffer, 501-1116 cg3 color
           framebuffer, and 501-1267 cg5 color framebuffer are mutually
           exclusive.

        && When installed with either the 501-1055 graphics processor or
           the 501-1139 graphics processor plus, the cg5 may be
           installed in slots 2-4 only.

        $  The gp5's P2 bus must be disabled.

        #  If you wish to install a Multibus-VME converter-based board
           in slots 2-4, you just use converters 501-1054-04 rev A or
           later to avoid contention on the P2 memory bus.

           If you wish to install a Multibus-VME converted-based board
           in slots 5-6 and any combination of GP and GP boards are
           installed, you must use converters 501-1054-04 rev A or later
           to avoid contention on the GP/GB private bus.

        ## The 501-1157 ALM-1 covers slots 5 and 6 but only connects
           electrically to slot 6. Hence, treat slot 5 as empty (i.e.
           jump both P503 and P504).

        %  The 501-1268 GP2 will not function if any of the 501-1058
           graphics buffer, the 501-1116 Sun-3 color board (cg3), or the
           501-1014 Sun-2 color board are installed.

        %% The GP2 communicates with the 501-1267 cg5 over a private P2
           bus which must be enabled on the cg5 by a hardware switch
           setting. The cg5 must also be installed in slot 6.

        @  The 370-1128 SunLink Channel Adapter uses two slots. The Px03
           and Px04 jumpers must be unjumpered for both slots.
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the channel adapter and the
           CPU, or the channel adapter's throughput may be adversely
           affected.

        @@ The 501-1202 MAPKIT covers two slots but only connects
           electrically to the slot nearest slot 1. Hence, treat the
           other slot as empty (i.e. jump both Px03 and Px04).

        !  See "Important Note about ALM and MCP products", below.

    3/160 using internal-connection-only or internal/external SCSI controller
          (for systems without a SCSI controller, use the "3/180 using
          external-connection-only SCSI controller" table below)

        board           slot:   1  2#^3# 4# 5# 6# 7  8  9 10#11#12#Px03 Px04
        CPU *                   A  -  -  -  -  -  -  -  -  -  -  -  UN   UN
        1st memory $$           -  -  -  -  A  -  -  -  -  -  -  -  JU   JU
        2nd memory $$           -  -  -  A  -  -  -  -  -  -  -  -  JU   JU
        3rd memory $$           -  -  A  -  -  -  -  -  -  -  -  -  JU   JU
        FPA 501-1105            -  -  -  -  -  A  -  -  -  -  -  -  JU   JU
        GP/GP+/GP2 ** % %%      -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        GB 501-1058 # %         -  -  -  -  -  -  -  -  -  -  A  -  JU   JU
        TAAC-1 501-1383 ~       -  -  -  -  -  -  -  -  -  A  -  -  JU   JU
        ALM-1 501-1157 # ## !   -  -  -  -  -  -  -  -  -  -  -  A  UN   N/A
        SCSI 501-1149/1167/1170 -  -  -  -  -  -  A  -  -  -  -  -  UN   UN
        1st SCP 501-1158 #      -  E  A  B  C  D  -  -  -  -  -  -  UN   UN
        2nd SCP 501-1158 #      -  D  -  A  B  C  E  F  -  -  -  -  UN   UN
        1st MCP 501-1221 !      -  E  A  B  C  D  F  G  H  -  -  -  UN   UN
        2nd MCP 501-1221 !      -  D  -  A  B  C  E  F  G  H  I  J  UN   UN
        3rd MCP 501-1221 !      -  C  -  -  A  B  D  E  F  G  H  I  UN   UN
        4th MCP 501-1221 !      -  B  -  -  -  A  C  D  E  F  G  H  UN   UN
        1st ALM-2 501-1203 !    -  E  A  B  C  D  F  G  H  I  J  K  UN   UN
        2nd ALM-2 501-1203 !    -  D  -  A  B  C  E  F  G  H  I  J  UN   UN
        3rd ALM-2 501-1203 !    -  C  -  -  A  B  D  E  F  G  H  I  UN   UN
        4th ALM-2 501-1203 !    -  B  -  -  -  A  C  D  E  F  G  H  UN   UN
        1st SunLink Chnl Adpt @ -  A  A  C  C  E  E  G  G  I  I  -  UN   UN
                                -  -  B  B  D  D  F  F  H  H  J  J
        2nd SunLink Chnl Adpt @ -  -  -  A  A  C  C  E  E  G  G  -  UN   UN
                                -  -  -  -  B  B  D  D  F  F  H  H
        1st MAPKIT 501-1202 @@  -  A  A  C  C  E  E  G  G  I  I  -  UN   UN
                                -  -  B  B  D  D  F  F  H  H  J  J
        2nd MAPKIT 501-1202 @@  -  -  -  A  A  C  C  E  E  G  G  -  UN   UN
                                -  -  -  -  B  B  D  D  F  F  H  H
        2nd Ethernet 501-1153 # -  E  A  B  C  D  F  G  H  I  J  K  UN   UN
        1st IPC 501-1125        -  E  A  B  C  D  F  G  H  I  J  K  JU   UN
        2nd IPC 501-1125        -  D  -  A  B  C  E  F  G  H  I  J  JU   UN
        3rd IPC 501-1125        -  C  -  -  A  B  D  E  F  G  H  I  JU   UN
        4th IPC 501-1125        -  B  -  -  -  A  C  D  E  F  G  H  JU   UN
        1st 1/2" tape !! #      -  -  -  -  -  -  A  B  C  D  E  F  UN   UN
        2nd 1/2" tape !! #      -  -  -  -  -  -  -  A  B  C  D  E  UN   UN
        1st SMD ~~ #            -  -  -  -  -  -  A  B  C  D  E  F  UN   UN
        2nd SMD ~~ #            -  -  -  -  -  -  -  A  B  C  D  E  UN   UN
        Sun-2 clr 501-1014 & %  -  K  A  B  C  D  E  F  G  H  I  J  JU   UN
        cg3 color 501-1116 & %  -  K  A  B  C  D  E  F  G  H  I  J  JU   UN
        cg5 color 501-1267 & $  -  K  A  B  C  D  E  F  G  H  I  J  JU   UN w/o GP or GP+
         "    "    "   "   && $ -  H  A  B  C  D  E  F  G  -  -  -  JU   UN with GP or GP+
         "    "    "   "   %%   -  -  -  -  -  -  -  -  -  -  A  B  JU   UN with GP2

        *  501-1163     2M CPU
           501-1164     4M CPU
           501-1208     4M CPU

        ** 501-1055     Graphics Processor
           501-1139     Graphics Processor Plus
           501-1268     Graphics Processor 2

        &  The 501-1014 Sun-2 color framebuffer, 501-1116 cg3 color
           framebuffer, and 501-1267 cg5 color framebuffer are mutually
           exclusive.

        && When installed with either the 501-1055 graphics processor or
           the 501-1139 graphics processor plus, the cg5 may be
           installed in slots 2-9 only.

        $  The gp5's P2 bus must be disabled.

        $$ 501-1131     2M memory
           501-1132     4M memory

        !  See "Important Note about ALM and MCP products", below.

        !! 501-1156     CPC 1/2" tape controller (1600 BPI)
           501-1155     Xylogics 472 1/2" tape controller (6250 BPI)

        ~  The 501-1383 TAAC-1 consumes three spaces (slots 10, 11, and
           12). Besides jumpering P1003 and P1004 as shown in the table
           above, P1103, P1104, and P1203 must be jumpered (P1204 does
           not exist).

        ~~ 501-1154     Xylogics 450 SMD controller in Multibus-VME converter
           501-1166     Xylogics 451 SMD controller in Multibus-VME converter

        %  The 501-1268 GP2 will not function if any of the 501-1058
           graphics buffer, the 501-1116 Sun-3 color board (cg3), or the
           501-1014 Sun-2 color board are installed.

        %% The GP2 communicates with the 501-1267 cg5 over a private P2
           bus which must be enabled on the cg5 by a hardware switch
           setting. The cg5 must also be installed in slot 11 or 12.

        #  If you wish to install a Multibus-VME converter-based board
           in slots 2-6, you just use converters 501-1054-04 rev A or
           later to avoid contention on the P2 memory bus.

           If you wish to install a Multibus-VME converted-based board
           in slots 10-12 and any combination of GP and GP boards are
           installed, you must use converters 501-1054-04 rev A or later
           to avoid contention on the GP/GB private bus.

        ## The 501-1157 ALM-1 covers slots 11 and 12 but only connects
           electrically to slot 12. Hence, treat slot 11 as empty (i.e.
           jump both P1103 and P1104).

        @  The 370-1128 SunLink Channel Adapter uses two slots. The Px03
           and Px04 jumpers must be unjumpered for both slots.
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the channel adapter and the
           CPU, or the channel adapter's throughput may be adversely
           affected.

        @@ The 501-1202 MAPKIT covers two slots but only connects
           electrically to the slot nearest slot 1. Hence, treat the
           other slot as empty (i.e. jump both Px03 and Px04).
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the MAPKIT and the CPU, or
           the MAPKIT's throughput may be adversely affected.

        ^  Avoid using slot 2 until absolutely necessary, to aid cooling
           of the CPU board. That is, if there is another slot available
           in which a board can be installed (even if it is not the most
           preferred slot) without impacting the functionality of
           another board, it should be installed in that slot instead of
           slot 2.

    3/180 using external-connection-only SCSI controller

        board           slot:   1  2# 3# 4# 5# 6# 7  8  9 10#11#12#Px03 Px04
        CPU *                   A  -  -  -  -  -  -  -  -  -  -  -  UN   UN
        1st memory $$           -  A  -  -  -  -  -  -  -  -  -  -  JU   JU
        2nd memory $$           -  -  A  -  -  -  -  -  -  -  -  -  JU   JU
        3rd memory $$           -  -  -  A  -  -  -  -  -  -  -  -  JU   JU
        FPA 501-1105            -  -  -  -  -  A  -  -  -  -  -  -  JU   JU
        GP/GP+/GP2 ** % %%      -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        GB 501-1058 # %         -  -  -  -  -  -  -  -  -  -  A  -  JU   JU
        TAAC-1 501-1383 ~       -  -  -  -  -  -  -  -  -  A  -  -  JU   JU
        1st ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  -  -  A  UN   N/A
        2nd ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  -  A  -  UN   UN
        3rd ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        1st SCP 501-1158 #      -  A  B  C  D  -  -  -  -  -  -  -  UN   UN
        2nd SCP 501-1158 #      -  -  A  B  C  D  E  -  -  -  -  -  UN   UN
        1st MCP 501-1221 !      -  A  B  C  D  E  F  G  -  -  -  -  UN   UN
        2nd MCP 501-1221 !      -  -  A  B  C  D  E  F  G  -  -  -  UN   UN
        3rd MCP 501-1221 !      -  -  -  A  B  C  D  E  F  G  H  I  UN   UN
        4th MCP 501-1221 !      -  -  -  -  A  B  C  D  E  F  G  H  UN   UN
        1st ALM-2 501-1203 !    -  A  B  C  D  E  F  G  H  I  J  K  UN   UN
        2nd ALM-2 501-1203 !    -  -  A  B  C  D  E  F  G  H  I  J  UN   UN
        3rd ALM-2 501-1203 !    -  -  -  A  B  C  D  E  F  G  H  I  UN   UN
        4th ALM-2 501-1203 !    -  -  -  -  A  B  C  D  E  F  G  H  UN   UN
        1st SunLink Chnl Adpt @ -  A  A  C  C  E  E  G  G  I  I  -  UN   UN
                                -  -  B  B  D  D  F  F  H  H  J  J
        2nd SunLink Chnl Adpt @ -  -  -  A  A  C  C  E  E  G  G  -  UN   UN
                                -  -  -  -  B  B  D  D  F  F  H  H
        1st MAPKIT 501-1202 @@  -  A  A  C  C  E  E  G  G  I  I  -  UN   UN
                                -  -  B  B  D  D  F  F  H  H  J  J
        2nd MAPKIT 501-1202 @@  -  -  -  A  A  C  C  E  E  G  G  -  UN   UN
                                -  -  -  -  B  B  D  D  F  F  H  H
        SCSI 501-1138/1217      -  A  B  C  D  E  F  G  H  I  J  K  UN   UN
        Sun-2 clr 501-1014 & %  -  A  B  C  D  E  F  G  H  I  J  K  JU   UN
        cg3 color 501-1116 & %  -  A  B  C  D  E  F  G  H  I  J  K  JU   UN
        cg5 color 501-1267 & $  -  A  B  C  D  E  F  G  H  I  J  K  JU   UN w/o GP or GP+
         "    "    "   "   && $ -  A  B  C  D  E  F  G  H  -  -  -  JU   UN with GP or GP+
         "    "    "   "   %%   -  -  -  -  -  -  -  -  -  -  A  B  JU   UN with GP2
        2nd Ethernet 501-1153 # -  A  B  C  D  E  F  G  H  I  J  K  UN   UN
        1st IPC 501-1125        -  A  B  C  D  E  F  G  H  I  J  K  JU   UN
        2nd IPC 501-1125        -  -  A  B  C  D  E  F  G  H  I  J  JU   UN
        3rd IPC 501-1125        -  -  -  A  B  C  D  E  F  G  H  I  JU   UN
        4th IPC 501-1125        -  -  -  -  A  B  C  D  E  F  G  H  JU   UN
        1st 1/2" tape !! #      -  A  B  C  D  E  F  G  H  I  J  K  UN   UN
        2nd 1/2" tape !! #      -  -  A  B  C  D  E  F  G  H  I  J  UN   UN
        1st SMD ~~ #            -  A  B  C  D  E  F  G  H  I  J  K  UN   UN
        2nd SMD ~~ #            -  -  A  B  C  D  E  F  G  H  I  J  UN   UN

        *  501-1163     2M CPU
           501-1164     4M CPU
           501-1208     4M CPU

        ** 501-1055     Graphics Processor
           501-1139     Graphics Processor Plus
           501-1268     Graphics Processor 2

        &  The 501-1014 Sun-2 color framebuffer, 501-1116 cg3 color
           framebuffer, and 501-1267 cg5 color framebuffer are mutually
           exclusive.

        && When installed with either the 501-1055 graphics processor or
           the 501-1139 graphics processor plus, the cg5 may be
           installed in slots 2-9 only.

        $  The gp5's P2 bus must be disabled.

        $$ 501-1131     2M memory
           501-1132     4M memory

        %  The 501-1268 GP2 will not function if any of the 501-1058
           graphics buffer, the 501-1116 Sun-3 color board (cg3), or the
           501-1014 Sun-2 color board are installed.

        %% The GP2 communicates with the 501-1267 cg5 over a private P2
           bus which must be enabled on the cg5 by a hardware switch
           setting. The cg5 must also be installed in slot 11 or 12.

        !  See "Important Note about ALM and MCP products", below.

        !! 501-1156     CPC 1/2" tape controller (1600 BPI)
           501-1155     Xylogics 472 1/2" tape controller (6250 BPI)

        ~  The 501-1383 TAAC-1 consumes three spaces (slots 10, 11, and
           12). Besides jumpering P1003 and P1004 as shown in the table
           above, P1103, P1104, and P1203 must be jumpered (P1204 does
           not exist).

        ~~ 501-1154     Xylogics 450 SMD controller in Multibus-VME converter
           501-1166     Xylogics 451 SMD controller in Multibus-VME converter

        #  If you wish to install a Multibus-VME converter-based board
           in slots 2-6, you just use converters 501-1054-04 rev A or
           later to avoid contention on the P2 memory bus.

           If you wish to install a Multibus-VME converted-based board
           in slots 10-12 and any combination of GP and GP boards are
           installed, you must use converters 501-1054-04 rev A or later
           to avoid contention on the GP/GB private bus.

        @  The 370-1128 SunLink Channel Adapter uses two slots. The Px03
           and Px04 jumpers must be unjumpered for both slots.
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the channel adapter and the
           CPU, or the channel adapter's throughput may be adversely
           affected.

        @@ The 501-1202 MAPKIT covers two slots but only connects
           electrically to the slot nearest slot 1. Hence, treat the
           other slot as empty (i.e. jump both Px03 and Px04).
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the MAPKIT and the CPU, or
           the MAPKIT's throughput may be adversely affected.

    3/180 using internal-connection-only or internal/external SCSI controller

        board           slot:   1  2# 3# 4# 5# 6# 7  8  9 10#11#12#Px03 Px04
        CPU *                   A  -  -  -  -  -  -  -  -  -  -  -  UN   UN
        1st memory $$           -  A  -  -  -  -  -  -  -  -  -  -  JU   JU
        2nd memory $$           -  -  A  -  -  -  -  -  -  -  -  -  JU   JU
        3rd memory $$           -  -  -  A  -  -  -  -  -  -  -  -  JU   JU
        FPA 501-1105            -  -  -  -  -  A  -  -  -  -  -  -  JU   JU
        GP/GP+/GP2 ** % %%      -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        GB 501-1058 # %         -  -  -  -  -  -  -  -  -  -  A  -  JU   JU
        TAAC-1 501-1383 ~       -  -  -  -  -  -  -  -  -  A  -  -  JU   JU
        1st ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  -  -  A  UN   N/A
        2nd ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  -  A  -  UN   UN
        3rd ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        SCSI 501-1149/1167/1170 -  -  -  -  -  -  A  -  -  -  -  -  UN   UN
        1st SCP 501-1158 #      -  A  B  C  D  -  -  -  -  -  -  -  UN   UN
        2nd SCP 501-1158 #      -  -  A  B  C  D  -  E  -  -  -  -  UN   UN
        1st MCP 501-1221 !      -  A  B  C  D  E  -  F  G  -  -  -  UN   UN
        2nd MCP 501-1221 !      -  -  A  B  C  D  -  E  F  G  H  I  UN   UN
        3rd MCP 501-1221 !      -  -  -  A  B  C  -  D  E  F  G  H  UN   UN
        4th MCP 501-1221 !      -  -  -  -  A  B  -  C  D  E  F  G  UN   UN
        1st ALM-2 501-1203 !    -  A  B  C  D  E  -  F  G  H  I  J  UN   UN
        2nd ALM-2 501-1203 !    -  -  A  B  C  D  -  E  F  G  H  I  UN   UN
        3rd ALM-2 501-1203 !    -  -  -  A  B  C  -  D  E  F  G  H  UN   UN
        4th ALM-2 501-1203 !    -  -  -  -  A  B  -  C  D  E  F  G  UN   UN
        1st SunLink Chnl Adpt @ -  A  A  C  C  -  -  E  E  G  G  -  UN   UN
                                -  -  B  B  D  D  -  -  F  F  H  H
        2nd SunLink Chnl Adpt @ -  -  -  A  A  -  -  C  C  E  E  -  UN   UN
                                -  -  -  -  B  B  -  -  D  D  F  F
        1st MAPKIT 501-1202 @@  -  A  A  C  C  -  -  E  E  G  G  -  UN   UN
                                -  -  B  B  D  D  -  -  F  F  H  H
        2nd MAPKIT 501-1202 @@  -  -  -  A  A  -  -  C  C  E  E  -  UN   UN
                                -  -  -  -  B  B  -  -  D  D  F  F
        Sun-2 clr 501-1014 & %  -  A  B  C  D  E  -  F  G  H  I  J  JU   UN
        cg3 color 501-1116 & %  -  A  B  C  D  E  -  F  G  H  I  J  JU   UN
        cg5 color 501-1267 & $  -  A  B  C  D  E  -  F  G  H  I  J  JU   UN w/o GP or GP+
         "    "    "   "   && $ -  A  B  C  D  E  -  F  G  -  -  -  JU   UN with GP or GP+
         "    "    "   "   %%   -  -  -  -  -  -  -  -  -  -  A  B  JU   UN with GP2
        2nd Ethernet 501-1153 # -  A  B  C  D  E  -  F  G  H  I  J  UN   UN
        1st IPC 501-1125        -  A  B  C  D  E  -  F  G  H  I  J  JU   UN
        2nd IPC 501-1125        -  -  A  B  C  D  -  E  F  G  H  I  JU   UN
        3rd IPC 501-1125        -  -  -  A  B  C  -  D  E  F  G  H  JU   UN
        4th IPC 501-1125        -  -  -  -  A  B  -  C  D  E  F  G  JU   UN
        1st 1/2" tape !! #      -  -  -  -  -  -  -  A  B  C  D  E  UN   UN
        2nd 1/2" tape !! #      -  -  -  -  -  -  -  -  A  B  C  D  UN   UN
        1st SMD ~~ #            -  -  -  -  -  -  -  A  B  C  D  E  UN   UN
        2nd SMD ~~ #            -  -  -  -  -  -  -  -  A  B  C  D  UN   UN

        *  501-1163     2M CPU
           501-1164     4M CPU
           501-1208     4M CPU

        ** 501-1055     Graphics Processor
           501-1139     Graphics Processor Plus
           501-1268     Graphics Processor 2

        &  The 501-1014 Sun-2 color framebuffer, 501-1116 cg3 color
           framebuffer, and 501-1267 cg5 color framebuffer are mutually
           exclusive.

        && When installed with either the 501-1055 graphics processor or
           the 501-1139 graphics processor plus, the cg5 may be
           installed in slots 2-9 only.

        $  The gp5's P2 bus must be disabled.

        $$ 501-1131     2M memory
           501-1132     4M memory

        !  See "Important Note about ALM and MCP products", below.

        !! 501-1156     CPC 1/2" tape controller (1600 BPI)
           501-1155     Xylogics 472 1/2" tape controller (6250 BPI)

        ~  The 501-1383 TAAC-1 consumes three spaces (slots 10, 11, and
           12). Besides jumpering P1003 and P1004 as shown in the table
           above, P1103, P1104, and P1203 must be jumpered (P1204 does
           not exist).

        ~~ 501-1154     Xylogics 450 SMD controller in Multibus-VME converter
           501-1166     Xylogics 451 SMD controller in Multibus-VME converter

        %  The 501-1268 GP2 will not function if any of the 501-1058
           graphics buffer, the 501-1116 Sun-3 color board (cg3), or the
           501-1014 Sun-2 color board are installed.

        %% The GP2 communicates with the 501-1267 cg5 over a private P2
           bus which must be enabled on the cg5 by a hardware switch
           setting. The cg5 must also be installed in slot 11 or 12.

        #  If you wish to install a Multibus-VME converter-based board
           in slots 2-6, you just use converters 501-1054-04 rev A or
           later to avoid contention on the P2 memory bus.

           If you wish to install a Multibus-VME converted-based board
           in slots 10-12 and any combination of GP and GP boards are
           installed, you must use converters 501-1054-04 rev A or later
           to avoid contention on the GP/GB private bus.

        @  The 370-1128 SunLink Channel Adapter uses two slots. The Px03
           and Px04 jumpers must be unjumpered for both slots.
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the channel adapter and the
           CPU, or the channel adapter's throughput may be adversely
           affected.

        @@ The 501-1202 MAPKIT covers two slots but only connects
           electrically to the slot nearest slot 1. Hence, treat the
           other slot as empty (i.e. jump both Px03 and Px04).
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the MAPKIT and the CPU, or
           the MAPKIT's throughput may be adversely affected.

    3/180 using external-connection-only SCSI controller and leaving
          slots 7-9 for non-Sun boards that use P2 bus signals

        board           slot:   1  2# 3# 4# 5# 6# 7  8  9 10#11#12#Px03 Px04
        CPU *                   A  -  -  -  -  -  -  -  -  -  -  -  UN   UN
        1st memory $$           -  A  -  -  -  -  -  -  -  -  -  -  JU   JU
        2nd memory $$           -  -  A  -  -  -  -  -  -  -  -  -  JU   JU
        3rd memory $$           -  -  -  A  -  -  -  -  -  -  -  -  JU   JU
        FPA 501-1105            -  -  -  -  -  A  -  -  -  -  -  -  JU   JU
        GP/GP+/GP2 ** % %%      -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        GB 501-1058 # %         -  -  -  -  -  -  -  -  -  -  A  -  JU   JU
        TAAC-1 501-1383 ~       -  -  -  -  -  -  -  -  -  A  -  -  JU   JU
        1st ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  -  -  A  UN   N/A
        2nd ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  -  A  -  UN   UN
        3rd ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        1st SCP 501-1158 #      -  A  B  C  D  -  -  -  -  -  -  -  UN   UN
        2nd SCP 501-1158 #      -  -  A  B  C  D  -  -  -  E  F  G  UN   UN
        1st MCP 501-1221 !      -  A  B  C  D  E  -  -  -  F  G  H  UN   UN
        2nd MCP 501-1221 !      -  -  A  B  C  D  -  -  -  E  F  G  UN   UN
        3rd MCP 501-1221 !      -  -  -  A  B  C  -  -  -  D  E  F  UN   UN
        4th MCP 501-1221 !      -  -  -  -  A  B  -  -  -  C  D  E  UN   UN
        1st ALM-2 501-1203 !    -  A  B  C  D  E  -  -  -  F  G  H  UN   UN
        2nd ALM-2 501-1203 !    -  -  A  B  C  D  -  -  -  E  F  G  UN   UN
        3rd ALM-2 501-1203 !    -  -  -  A  B  C  -  -  -  D  E  F  UN   UN
        4th ALM-2 501-1203 !    -  -  -  -  A  B  -  -  -  -  C  D  UN   UN
        1st SunLink Chnl Adpt @ -  A  A  C  C  -  -  -  -  E  E  -  UN   UN
                                -  -  B  B  D  D  -  -  -  -  F  F
        2nd SunLink Chnl Adpt @ -  -  -  A  A  -  -  -  -  C  C  -  UN   UN
                                -  -  -  -  B  B  -  -  -  -  D  D
        1st MAPKIT 501-1202 @@  -  A  A  C  C     -  -  -  E  E  -  UN   UN
                                -  -  B  B  D  D  -  -  -  -  F  F
        2nd MAPKIT 501-1202 @@  -  -  -  A  A     -  -  -  C  C  -  UN   UN
                                -  -  -  -  B  B  -  -  -  -  D  D
        SCSI 501-1138/1217      -  A  B  C  D  E  -  -  -  F  G  H  UN   UN
        Sun-2 clr 501-1014 & %  -  A  B  C  D  E  -  -  -  F  G  H  JU   UN
        cg3 color 501-1116 & %  -  A  B  C  D  E  -  -  -  F  G  H  JU   UN
        cg5 color 501-1267 & $  -  A  B  C  D  E  -  -  -  F  G  H  JU   UN w/o GP or GP+
         "    "    "   "   && $ -  A  B  C  D  E  -  -  -  -  -  -  JU   UN with GP or GP+
         "    "    "   "   %%   -  -  -  -  -  -  -  -  -  -  A  B  JU   UN with GP2
        2nd Ethernet 501-1153 # -  A  B  C  D  E  -  -  -  F  G  H  UN   UN
        1st IPC 501-1125        -  A  B  C  D  E  -  -  -  F  G  H  JU   UN
        2nd IPC 501-1125        -  -  A  B  C  D  -  -  -  E  F  G  JU   UN
        3rd IPC 501-1125        -  -  -  A  B  C  -  -  -  D  E  F  JU   UN
        4th IPC 501-1125        -  -  -  -  A  B  -  -  -  C  D  E  JU   UN
        1st 1/2" tape !! #      -  A  B  C  D  E  -  -  -  F  G  H  UN   UN
        2nd 1/2" tape !! #      -  -  A  B  C  D  -  -  -  E  F  G  UN   UN
        1st SMD ~~ #            -  A  B  C  D  E  -  -  -  F  G  H  UN   UN
        2nd SMD ~~ #            -  -  A  B  C  D  -  -  -  E  F  G  UN   UN

        *  501-1163     2M CPU
           501-1164     4M CPU
           501-1208     4M CPU

        ** 501-1055     Graphics Processor
           501-1139     Graphics Processor Plus
           501-1268     Graphics Processor 2

        &  The 501-1014 Sun-2 color framebuffer, 501-1116 cg3 color
           framebuffer, and 501-1267 cg5 color framebuffer are mutually
           exclusive.

        && When installed with either the 501-1055 graphics processor or
           the 501-1139 graphics processor plus, the cg5 may be
           installed in slots 2-9 only.

        $  The gp5's P2 bus must be disabled.

        $$ 501-1131     2M memory
           501-1132     4M memory

        !  See "Important Note about ALM and MCP products", below.

        !! 501-1156     CPC 1/2" tape controller (1600 BPI)
           501-1155     Xylogics 472 1/2" tape controller (6250 BPI)

        ~  The 501-1383 TAAC-1 consumes three spaces (slots 10, 11, and
           12). Besides jumpering P1003 and P1004 as shown in the table
           above, P1103, P1104, and P1203 must be jumpered (P1204 does
           not exist).

        ~~ 501-1154     Xylogics 450 SMD controller in Multibus-VME converter
           501-1166     Xylogics 451 SMD controller in Multibus-VME converter

        %  The 501-1268 GP2 will not function if any of the 501-1058
           graphics buffer, the 501-1116 Sun-3 color board (cg3), or the
           501-1014 Sun-2 color board are installed.

        %% The GP2 communicates with the 501-1267 cg5 over a private P2
           bus which must be enabled on the cg5 by a hardware switch
           setting. The cg5 must also be installed in slot 11 or 12.

        #  If you wish to install a Multibus-VME converter-based board
           in slots 2-6, you just use converters 501-1054-04 rev A or
           later to avoid contention on the P2 memory bus.

           If you wish to install a Multibus-VME converted-based board
           in slots 10-12 and any combination of GP and GP boards are
           installed, you must use converters 501-1054-04 rev A or later
           to avoid contention on the GP/GB private bus.

        @  The 370-1128 SunLink Channel Adapter uses two slots. The Px03
           and Px04 jumpers must be unjumpered for both slots.
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the channel adapter and the
           CPU, or the channel adapter's throughput may be adversely
           affected.

        @@ The 501-1202 MAPKIT covers two slots but only connects
           electrically to the slot nearest slot 1. Hence, treat the
           other slot as empty (i.e. jump both Px03 and Px04).
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the MAPKIT and the CPU, or
           the MAPKIT's throughput may be adversely affected.

    3/260 using internal-connection-only or internal/external SCSI controller
          (for systems without a SCSI controller, use the "3/280 using
          external-connection-only SCSI controller" table below)

        board           slot:   1  2#~3# 4# 5# 6  7  8  9 10#11#12#Px03 Px04
        CPU 501-1100/1206       A  -  -  -  -  -  -  -  -  -  -  -  UN   UN
        1st memory 501-1102 *   -  -  -  -  -  A  -  -  -  -  -  -  JU   JU
        2nd memory 501-1102 *   -  -  -  A  -  -  -  -  -  -  -  -  JU   JU
        3rd memory 501-1102 *   -  -  A  -  -  -  -  -  -  -  -  -  JU   JU
        4th memory 501-1102 *   -  A  -  -  -  -  -  -  -  -  -  -  JU   JU
        FPA 501-1105            -  -  -  -  A  -  -  -  -  -  -  -  JU   JU
        GP/GP+/GP2 ** % %%      -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        GB 501-1058 # %         -  -  -  -  -  -  -  -  -  -  A  -  JU   JU
        TAAC-1 501-1383 ~~      -  -  -  -  -  -  -  -  -  A  -  -  JU   JU
        ALM-1 501-1157 # !! !   -  -  -  -  -  -  -  -  -  -  -  A  UN   N/A
        SCSI 501-1149/1167/1170 -  -  -  -  -  -  A  -  -  -  -  -  UN   UN
        1st SCP 501-1158 #      -  D  A  B  C  -  E  F  -  -  -  -  UN   UN
        2nd SCP 501-1158 #      -  C  -  A  B  -  D  E  F  -  -  -  UN   UN
        1st MCP 501-1221 !      -  D  A  B  C  -  E  F  G  H  I  J  UN   UN
        2nd MCP 501-1221 !      -  C  -  A  B  -  D  E  F  G  H  I  UN   UN
        3rd MCP 501-1221 !      -  B  -  -  A  -  C  D  E  F  G  H  UN   UN
        4th MCP 501-1221 !      -  A  -  -  -  -  B  C  D  E  F  G  UN   UN
        1st ALM-2 501-1203 !    -  D  A  B  C  -  E  F  G  H  I  J  UN   UN
        2nd ALM-2 501-1203 !    -  C  -  A  B  -  D  E  F  G  H  I  UN   UN
        3rd ALM-2 501-1203 !    -  B  -  -  A  -  C  D  E  F  G  H  UN   UN
        4th ALM-2 501-1203 !    -  A  -  -  -  -  B  C  D  E  F  G  UN   UN
        1st SunLink Chnl Adpt @ -  A  A  C  C  -  D  D  F  F  H  H  UN   UN
                                -  -  B  B  -  -  -  E  E  G  G  -
        2nd SunLink Chnl Adpt @ -  -  -  A  A  -  B  B  D  D  F  F  UN   UN
                                -  -  -  -  -  -  -  C  C  E  E  -
        1st MAPKIT 501-1202 $$  -  A  A  C  C  -  D  D  F  F  H  H  UN   UN
                                -  -  B  B  -  -  -  E  E  G  G  -
        2nd MAPKIT 501-1202 $$  -  -  -  A  A  -  B  B  D  D  F  F  UN   UN
                                -  -  -  -  -  -  -  C  C  E  E  -
        2nd Ethernet 501-1153 # -  D  A  B  C  -  E  F  G  H  I  J  UN   UN
        1st IPC 501-1125        -  D  A  B  C  -  E  F  G  H  I  J  JU   UN
        2nd IPC 501-1125        -  C  -  A  B  -  D  E  F  G  H  I  JU   UN
        3rd IPC 501-1125        -  B  -  -  A  -  C  D  E  F  G  H  JU   UN
        4th IPC 501-1125        -  A  -  -  -  -  B  C  D  E  F  G  JU   UN
        1st 1/2" tape ## #      -  -  -  -  -  -  A  B  C  D  E  F  UN   UN
        2nd 1/2" tape ## #      -  -  -  -  -  -  -  A  B  C  D  E  UN   UN
        1st SMD @@ #            -  -  -  -  -  -  A  B  C  D  E  F  UN   UN
        2nd SMD @@ #            -  -  -  -  -  -  -  A  B  C  D  E  UN   UN
        Sun-2 clr 501-1014 & %  -  J  A  B  C  -  D  E  F  G  H  I  JU   UN
        cg3 color 501-1116 & %  -  J  A  B  C  -  D  E  F  G  H  I  JU   UN
        cg5 color 501-1267 & $  -  J  A  B  C  -  D  E  F  G  H  I  JU   UN w/o GP or GP+
         "    "    "   "   && $ -  H  A  B  C  -  D  E  F  -  -  -  JU   UN with GP or GP+
         "    "    "   "   %%   -  -  -  -  -  -  -  -  -  -  A  B  JU   UN with GP2

        #  If you wish to install a Multibus-VME converter-based board
           in slots 2-5, you just use converters 501-1054-04 rev A or
           later to avoid contention on the P2 memory bus.

           If you wish to install a Multibus-VME converted-based board
           in slots 10-12 and any combination of GP and GP boards are
           installed, you must use converters 501-1054-04 rev A or later
           to avoid contention on the GP/GB private bus.

        ## 501-1156     CPC 1/2" tape controller (1600 BPI)
           501-1155     Xylogics 472 1/2" tape controller (6250 BPI)

        ~  Avoid using slot 2 until absolutely necessary, to aid cooling
           of the CPU board. That is, if there is another slot available
           in which a board can be installed (even if it is not the most
           preferred slot) without impacting the functionality of
           another board, it should be installed in that slot instead of
           slot 2.

        ~~ The 501-1383 TAAC-1 consumes three spaces (slots 10, 11, and
           12). Besides jumpering P1003 and P1004 as shown in the table
           above, P1103, P1104, and P1203 must be jumpered (P1204 does
           not exist).

        *  There must always be a memory board in slot 6 and it must
           have a 220/270-ohm terminating resistor network installed
           (see detailed description of board). Additional memory
           boards in slots 2-4 must NOT have the terminator installed.

        ** 501-1055     Graphics Processor
           501-1139     Graphics Processor Plus
           501-1268     Graphics Processor 2

        %  The 501-1268 GP2 will not function if any of the 501-1058
           graphics buffer, the 501-1116 Sun-3 color board (cg3), or the
           501-1014 Sun-2 color board are installed.

        %% The GP2 communicates with the 501-1267 cg5 over a private P2
           bus which must be enabled on the cg5 by a hardware switch
           setting. The cg5 must also be installed in slot 11 or 12.

        !  See "Important Note about ALM and MCP products", below.

        !! The 501-1157 ALM covers slots 11 and 12 but only connects
           electrically to slot 12. Hence, treat slot 11 as empty (i.e.
           jump both P1103 and P1104).

        &  The 501-1014 Sun-2 color framebuffer, 501-1116 cg3 color
           framebuffer, and 501-1267 cg5 color framebuffer are mutually
           exclusive.

        && When installed with either the 501-1055 graphics processor or
           the 501-1139 graphics processor plus, the cg5 may be
           installed in slots 2-9 only.

        $  The gp5's P2 bus must be disabled.

        $$ The 501-1202 MAPKIT covers two slots but only connects
           electrically to the slot nearest slot 1. Hence, treat the
           other slot as empty (i.e. jump both Px03 and Px04).
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the MAPKIT and the CPU, or
           the MAPKIT's throughput may be adversely affected.

        @  The 370-1128 SunLink Channel Adapter uses two slots. The Px03
           and Px04 jumpers must be unjumpered for both slots.
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the channel adapter and the
           CPU, or the channel adapter's throughput may be adversely
           affected.

        @@ 501-1154     Xylogics 450 SMD controller in Multibus-VME converter
           501-1166     Xylogics 451 SMD controller in Multibus-VME converter

    3/280 using external-connection-only SCSI controller

        board           slot:   1  2# 3# 4# 5# 6  7  8  9 10#11#12#Px03 Px04
        CPU 501-1100/1206       A  -  -  -  -  -  -  -  -  -  -  -  UN   UN
        1st memory 501-1102 *   -  -  -  -  -  A  -  -  -  -  -  -  JU   JU
        2nd memory 501-1102 *   -  A  -  -  -  -  -  -  -  -  -  -  JU   JU
        3rd memory 501-1102 *   -  -  A  -  -  -  -  -  -  -  -  -  JU   JU
        4th memory 501-1102 *   -  -  -  A  -  -  -  -  -  -  -  -  JU   JU
        FPA 501-1105            -  -  -  -  A  -  -  -  -  -  -  -  JU   JU
        GP/GP+/GP2 ** % %%      -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        GB 501-1058 # %         -  -  -  -  -  -  -  -  -  -  A  -  JU   JU
        TAAC-1 501-1383 ~~      -  -  -  -  -  -  -  -  -  A  -  -  JU   JU
        1st ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  -  -  A  UN   N/A
        2nd ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  -  A  -  UN   UN
        3rd ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        1st SCP 501-1158 #      -  A  B  C  D  -  E  -  -  -  -  -  UN   UN
        2nd SCP 501-1158 #      -  -  A  B  C  -  D  E  -  -  -  -  UN   UN
        1st MCP 501-1221 !      -  A  B  C  D  -  E  F  G  -  -  -  UN   UN
        2nd MCP 501-1221 !      -  -  A  B  C  -  D  E  F  G  H  I  UN   UN
        3rd MCP 501-1221 !      -  -  -  A  B  -  C  D  E  F  G  H  UN   UN
        4th MCP 501-1221 !      -  -  -  -  A  -  B  C  D  E  F  G  UN   UN
        1st ALM-2 501-1203 !    -  A  B  C  D  -  E  F  G  H  I  J  UN   UN
        2nd ALM-2 501-1203 !    -  -  A  B  C  -  D  E  F  G  H  I  UN   UN
        3rd ALM-2 501-1203 !    -  -  -  A  B  -  C  D  E  F  G  H  UN   UN
        4th ALM-2 501-1203 !    -  -  -  -  A  -  B  C  D  E  F  G  UN   UN
        1st SunLink Chnl Adpt @ -  A  A  C  C  -  D  D  F  F  H  H  UN   UN
                                -  -  B  B  -  -  -  E  E  G  G  -
        2nd SunLink Chnl Adpt @ -  -  -  A  A  -  B  B  D  D  F  F  UN   UN
                                -  -  -  -  -  -  -  C  C  E  E  -
        1st MAPKIT 501-1202 $$  -  A  A  C  C  -  D  D  F  F  G  G  UN   UN
                                -  -  B  B  -  -  -  E  E  -  -  -
        2nd MAPKIT 501-1202 $$  -  -  A  A  -  -  B  B  D  D  F  F  UN   UN
                                -  -  -  -  -  -  -  C  C  E  E  -
        SCSI 501-1138/1217      -  A  B  C  D  -  E  F  G  H  I  J  UN   UN
        Sun-2 clr 501-1014 & %  -  A  B  C  D  -  E  F  G  H  I  J  JU   UN
        cg3 color 501-1116 & %  -  A  B  C  D  -  E  F  G  H  I  J  JU   UN
        cg5 color 501-1267 & $  -  A  B  C  D  -  E  F  G  H  I  J  JU   UN w/o GP or GP+
         "    "    "   "   && $ -  A  B  C  D  -  E  F  G  -  -  -  JU   UN with GP or GP+
         "    "    "   "   %%   -  -  -  -  -  -  -  -  -  -  A  B  JU   UN with GP2
        2nd Ethernet 501-1153 # -  A  B  C  D  -  E  F  G  H  I  J  UN   UN
        1st IPC 501-1125        -  A  B  C  D  -  E  F  G  H  I  J  JU   UN
        2nd IPC 501-1125        -  -  A  B  C  -  D  E  F  G  H  I  JU   UN
        3rd IPC 501-1125        -  -  -  A  B  -  C  D  E  F  G  H  JU   UN
        4th IPC 501-1125        -  -  -  -  A  -  B  C  D  E  F  G  JU   UN
        1st 1/2" tape ## #      -  A  B  C  D  -  E  F  G  H  I  J  UN   UN
        2nd 1/2" tape ## #      -  -  A  B  C  -  D  E  F  G  H  I  UN   UN
        1st SMD @@ #            -  A  B  C  D  -  E  F  G  H  I  J  UN   UN
        2nd SMD @@ #            -  -  A  B  C  -  D  E  F  G  H  I  UN   UN

        #  If you wish to install a Multibus-VME converter-based board
           in slots 2-5, you just use converters 501-1054-04 rev A or
           later to avoid contention on the P2 memory bus.

           If you wish to install a Multibus-VME converted-based board
           in slots 10-12 and any combination of GP and GP boards are
           installed, you must use converters 501-1054-04 rev A or later
           to avoid contention on the GP/GB private bus.

        ## 501-1156     CPC 1/2" tape controller (1600 BPI)
           501-1155     Xylogics 472 1/2" tape controller (6250 BPI)

        *  There must always be a memory board in slot 6 and it must
           have a 220/270-ohm terminating resistor network installed
           (see detailed description of board). Additional memory
           boards in slots 2-4 must NOT have the terminator installed.

        ** 501-1055     Graphics Processor
           501-1139     Graphics Processor Plus
           501-1268     Graphics Processor 2

        %  The 501-1268 GP2 will not function if any of the 501-1058
           graphics buffer, the 501-1116 Sun-3 color board (cg3), or the
           501-1014 Sun-2 color board are installed.

        %% The GP2 communicates with the 501-1267 cg5 over a private P2
           bus which must be enabled on the cg5 by a hardware switch
           setting. The cg5 must also be installed in slot 11 or 12.

        &  The 501-1014 Sun-2 color framebuffer, 501-1116 cg3 color
           framebuffer, and 501-1267 cg5 color framebuffer are mutually
           exclusive.

        && When installed with either the 501-1055 graphics processor or
           the 501-1139 graphics processor plus, the cg5 may be
           installed in slots 2-9 only.

        $  The gp5's P2 bus must be disabled.

        $$ The 501-1202 MAPKIT covers two slots but only connects
           electrically to the slot nearest slot 1. Hence, treat the
           other slot as empty (i.e. jump both Px03 and Px04).
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the MAPKIT and the CPU, or
           the MAPKIT's throughput may be adversely affected.

        @  The 370-1128 SunLink Channel Adapter uses two slots. The Px03
           and Px04 jumpers must be unjumpered for both slots.
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the channel adapter and the
           CPU, or the channel adapter's throughput may be adversely
           affected.

        @@ 501-1154     Xylogics 450 SMD controller in Multibus-VME converter
           501-1166     Xylogics 451 SMD controller in Multibus-VME converter

        !  See "Important Note about ALM and MCP products", below.

        ~~ The 501-1383 TAAC-1 consumes three spaces (slots 10, 11, and
           12). Besides jumpering P1003 and P1004 as shown in the table
           above, P1103, P1104, and P1203 must be jumpered (P1204 does
           not exist).

    3/280 using internal-connection-only or internal/external SCSI controller

        board           slot:   1  2# 3# 4# 5# 6  7  8  9 10#11#12#Px03 Px04
        CPU 501-1100/1206       A  -  -  -  -  -  -  -  -  -  -  -  UN   UN
        1st memory 501-1102 *   -  -  -  -  -  A  -  -  -  -  -  -  JU   JU
        2nd memory 501-1102 *   -  A  -  -  -  -  -  -  -  -  -  -  JU   JU
        3rd memory 501-1102 *   -  -  A  -  -  -  -  -  -  -  -  -  JU   JU
        4th memory 501-1102 *   -  -  -  A  -  -  -  -  -  -  -  -  JU   JU
        FPA 501-1105            -  -  -  -  A  -  -  -  -  -  -  -  JU   JU
        GP/GP+/GP2 ** % %%      -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        GB 501-1058 # %         -  -  -  -  -  -  -  -  -  -  A  -  JU   JU
        TAAC-1 501-1383 ~~      -  -  -  -  -  -  -  -  -  A  -  -  JU   JU
        1st ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  -  -  A  UN   N/A
        2nd ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  -  A  -  UN   UN
        3rd ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        SCSI 501-1149/1167/1170 -  -  -  -  -  -  A  -  -  -  -  -  UN   UN
        1st SCP 501-1158 #      -  A  B  C  D  -  -  E  -  -  -  -  UN   UN
        2nd SCP 501-1158 #      -  -  A  B  C  -  -  D  E  -  -  -  UN   UN
        1st MCP 501-1221 !      -  A  B  C  D  -  -  E  F  G  H  I  UN   UN
        2nd MCP 501-1221 !      -  -  A  B  C  -  -  D  E  F  G  H  UN   UN
        3rd MCP 501-1221 !      -  -  -  A  B  -  -  C  D  E  F  G  UN   UN
        4th MCP 501-1221 !      -  -  -  -  A  -  -  B  C  D  E  F  UN   UN
        1st ALM-2 501-1203 !    -  A  B  C  D  -  -  E  F  G  H  I  UN   UN
        2nd ALM-2 501-1203 !    -  -  A  B  C  -  -  D  E  F  G  H  UN   UN
        3rd ALM-2 501-1203 !    -  -  -  A  B  -  -  C  D  E  F  G  UN   UN
        4th ALM-2 501-1203 !    -  -  -  -  A  -  -  B  C  D  E  F  UN   UN
        1st SunLink Chnl Adpt @ -  A  A  C  C  -  -  D  D  F  F  -  UN   UN
                                -  -  B  B  -  -  -  -  E  E  G  G
        2nd SunLink Chnl Adpt @ -  -  -  A  A  -  -  B  B  D  D  -  UN   UN
                                -  -  -  -  -  -  -  -  C  C  E  E
        1st MAPKIT 501-1202 $$  -  A  A  C  C  -  -  D  D  F  F  -  UN   UN
                                -  -  B  B  -  -  -  -  -  -  E  E
        2nd MAPKIT 501-1202 $$  -  -  A  A  -  -  -  B  B  D  D  -  UN   UN
                                -  -  -  -  -  -  -  -  C  C  E  E
        Sun-2 clr 501-1014 & %  -  A  B  C  D  -  -  E  F  G  H  I  JU   UN
        cg3 color 501-1116 & %  -  A  B  C  D  -  -  E  F  G  H  I  JU   UN
        cg5 color 501-1267 & $  -  A  B  C  D  -  -  E  F  G  H  I  JU   UN w/o GP or GP+
         "    "    "   "   && $ -  A  B  C  D  -  -  E  F  -  -  -  JU   UN with GP or GP+
         "    "    "   "   %%   -  -  -  -  -  -  -  -  -  -  A  B  JU   UN with GP2
        2nd Ethernet 501-1153 # -  A  B  C  D  -  -  E  F  G  H  I  UN   UN
        1st IPC 501-1125        -  A  B  C  D  -  -  E  F  G  H  I  JU   UN
        2nd IPC 501-1125        -  -  A  B  C  -  -  D  E  F  G  H  JU   UN
        3rd IPC 501-1125        -  -  -  A  B  -  -  C  D  E  F  G  JU   UN
        4th IPC 501-1125        -  -  -  -  A  -  -  B  C  D  E  F  JU   UN
        1st 1/2" tape ## #      -  -  -  -  -  -  -  A  B  C  D  E  UN   UN
        2nd 1/2" tape ## #      -  -  -  -  -  -  -  -  A  B  C  D  UN   UN
        1st SMD @@ #            -  -  -  -  -  -  -  A  B  C  D  E  UN   UN
        2nd SMD @@ #            -  -  -  -  -  -  -  -  A  B  C  D  UN   UN

        #  If you wish to install a Multibus-VME converter-based board
           in slots 2-5, you just use converters 501-1054-04 rev A or
           later to avoid contention on the P2 memory bus.

           If you wish to install a Multibus-VME converted-based board
           in slots 10-12 and any combination of GP and GP boards are
           installed, you must use converters 501-1054-04 rev A or later
           to avoid contention on the GP/GB private bus.

        ## 501-1156     CPC 1/2" tape controller (1600 BPI)
           501-1155     Xylogics 472 1/2" tape controller (6250 BPI)

        *  There must always be a memory board in slot 6 and it must
           have a 220/270-ohm terminating resistor network installed
           (see detailed description of board). Additional memory
           boards in slots 2-4 must NOT have the terminator installed.

        ** 501-1055     Graphics Processor
           501-1139     Graphics Processor Plus
           501-1268     Graphics Processor 2

        %  The 501-1268 GP2 will not function if any of the 501-1058
           graphics buffer, the 501-1116 Sun-3 color board (cg3), or the
           501-1014 Sun-2 color board are installed.

        %% The GP2 communicates with the 501-1267 cg5 over a private P2
           bus which must be enabled on the cg5 by a hardware switch
           setting. The cg5 must also be installed in slot 11 or 12.

        &  The 501-1014 Sun-2 color framebuffer, 501-1116 cg3 color
           framebuffer, and 501-1267 cg5 color framebuffer are mutually
           exclusive.

        && When installed with either the 501-1055 graphics processor or
           the 501-1139 graphics processor plus, the cg5 may be
           installed in slots 2-9 only.

        $  The gp5's P2 bus must be disabled.

        $$ The 501-1202 MAPKIT covers two slots but only connects
           electrically to the slot nearest slot 1. Hence, treat the
           other slot as empty (i.e. jump both Px03 and Px04).
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the MAPKIT and the CPU, or
           the MAPKIT's throughput may be adversely affected.

        @  The 370-1128 SunLink Channel Adapter uses two slots. The Px03
           and Px04 jumpers must be unjumpered for both slots.
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the channel adapter and the
           CPU, or the channel adapter's throughput may be adversely
           affected.

        @@ 501-1154     Xylogics 450 SMD controller in Multibus-VME converter
           501-1166     Xylogics 451 SMD controller in Multibus-VME converter

        !  See "Important Note about ALM and MCP products", below.

        ~~ The 501-1383 TAAC-1 consumes three spaces (slots 10, 11, and
           12). Besides jumpering P1003 and P1004 as shown in the table
           above, P1103, P1104, and P1203 must be jumpered (P1204 does
           not exist).

    3/280 using external-connection-only SCSI controller and leaving
          slots 7-9 for non-Sun boards that use P2 bus signals

        board           slot:   1  2# 3# 4# 5# 6  7  8  9 10#11#12#Px03 Px04
        CPU 501-1100/1206       A  -  -  -  -  -  -  -  -  -  -  -  UN   UN
        1st memory 501-1102 *   -  -  -  -  -  A  -  -  -  -  -  -  JU   JU
        2nd memory 501-1102 *   -  A  -  -  -  -  -  -  -  -  -  -  JU   JU
        3rd memory 501-1102 *   -  -  A  -  -  -  -  -  -  -  -  -  JU   JU
        4th memory 501-1102 *   -  -  -  A  -  -  -  -  -  -  -  -  JU   JU
        FPA 501-1105            -  -  -  -  A  -  -  -  -  -  -  -  JU   JU
        GP/GP+/GP2 ** % %%      -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        GB 501-1058 # %         -  -  -  -  -  -  -  -  -  -  A  -  JU   JU
        TAAC-1 501-1383 ~~      -  -  -  -  -  -  -  -  -  A  -  -  JU   JU
        1st ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  -  -  A  UN   N/A
        2nd ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  -  A  -  UN   UN
        3rd ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        1st SCP 501-1158 #      -  A  B  C  D  -  -  -  -  E  F  G  UN   UN
        2nd SCP 501-1158 #      -  -  A  B  C  -  -  -  -  D  E  F  UN   UN
        1st MCP 501-1221 !      -  A  B  C  D  -  -  -  -  E  F  G  UN   UN
        2nd MCP 501-1221 !      -  -  A  B  C  -  -  -  -  D  E  F  UN   UN
        3rd MCP 501-1221 !      -  -  -  A  B  -  -  -  -  C  D  E  UN   UN
        4th MCP 501-1221 !      -  -  -  -  A  -  -  -  -  B  C  D  UN   UN
        1st ALM-2 501-1203 !    -  A  B  C  D  -  -  -  -  E  F  G  UN   UN
        2nd ALM-2 501-1203 !    -  -  A  B  C  -  -  -  -  D  E  F  UN   UN
        3rd ALM-2 501-1203 !    -  -  -  A  B  -  -  -  -  C  D  E  UN   UN
        4th ALM-2 501-1203 !    -  -  -  -  A  -  -  -  -  B  C  D  UN   UN
        1st SunLink Chnl Adpt @ -  A  A  C  C  -  -  -  -  D  D  -  UN   UN
                                -  -  B  B  -  -  -  -  -  -  E  E
        2nd SunLink Chnl Adpt @ -  -  -  A  A  -  -  -  -  B  B  -  UN   UN
                                -  -  -  -  -  -  -  -  -  -  C  C
        1st MAPKIT 501-1202 $$  -  A  A  C  C  -  -  -  -  D  D  -  UN   UN
                                -  -  B  B  -  -  -  -  -  -  -  -
        2nd MAPKIT 501-1202 $$  -  -  A  A  -  -  -  -  -  B  B  -  UN   UN
                                -  -  -  -  -  -  -  -  -  -  C  C
        SCSI 501-1138/1217      -  A  B  C  D  -  -  -  -  E  F  G  UN   UN
        Sun-2 clr 501-1014 & %  -  A  B  C  D  -  -  -  -  E  F  G  JU   UN
        cg3 color 501-1116 & %  -  A  B  C  D  -  -  -  -  E  F  G  JU   UN
        cg5 color 501-1267 & $  -  A  B  C  D  -  -  -  -  E  F  G  JU   UN w/o GP or GP+
         "    "    "   "   && $ -  A  B  C  D  -  -  -  -  -  -  -  JU   UN with GP or GP+
         "    "    "   "   %%   -  -  -  -  -  -  -  -  -  -  A  B  JU   UN with GP2
        2nd Ethernet 501-1153 # -  A  B  C  D  -  -  -  -  E  F  G  UN   UN
        1st IPC 501-1125        -  A  B  C  D  -  -  -  -  E  F  G  JU   UN
        2nd IPC 501-1125        -  -  A  B  C  -  -  -  -  D  E  F  JU   UN
        3rd IPC 501-1125        -  -  -  A  B  -  -  -  -  C  D  E  JU   UN
        4th IPC 501-1125        -  -  -  -  A  -  -  -  -  B  C  D  JU   UN
        1st 1/2" tape ## #      -  A  B  C  D  -  -  -  -  E  F  G  UN   UN
        2nd 1/2" tape ## #      -  -  A  B  C  -  -  -  -  D  E  F  UN   UN
        1st SMD @@ #            -  A  B  C  D  -  -  -  -  E  F  G  UN   UN
        2nd SMD @@ #            -  -  A  B  C  -  -  -  -  D  E  F  UN   UN

        #  If you wish to install a Multibus-VME converter-based board
           in slots 2-5, you just use converters 501-1054-04 rev A or
           later to avoid contention on the P2 memory bus.

           If you wish to install a Multibus-VME converted-based board
           in slots 10-12 and any combination of GP and GP boards are
           installed, you must use converters 501-1054-04 rev A or later
           to avoid contention on the GP/GB private bus.

        ## 501-1156     CPC 1/2" tape controller (1600 BPI)
           501-1155     Xylogics 472 1/2" tape controller (6250 BPI)

        *  There must always be a memory board in slot 6 and it must
           have a 220/270-ohm terminating resistor network installed
           (see detailed description of board). Additional memory
           boards in slots 2-4 must NOT have the terminator installed.

        ** 501-1055     Graphics Processor
           501-1139     Graphics Processor Plus
           501-1268     Graphics Processor 2

        %  The 501-1268 GP2 will not function if any of the 501-1058
           graphics buffer, the 501-1116 Sun-3 color board (cg3), or the
           501-1014 Sun-2 color board are installed.

        %% The GP2 communicates with the 501-1267 cg5 over a private P2
           bus which must be enabled on the cg5 by a hardware switch
           setting. The cg5 must also be installed in slot 11 or 12.

        &  The 501-1014 Sun-2 color framebuffer, 501-1116 cg3 color
           framebuffer, and 501-1267 cg5 color framebuffer are mutually
           exclusive.

        && When installed with either the 501-1055 graphics processor or
           the 501-1139 graphics processor plus, the cg5 may be
           installed in slots 2-9 only.

        $  The gp5's P2 bus must be disabled.

        $$ The 501-1202 MAPKIT covers two slots but only connects
           electrically to the slot nearest slot 1. Hence, treat the
           other slot as empty (i.e. jump both Px03 and Px04).
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the MAPKIT and the CPU, or
           the MAPKIT's throughput may be adversely affected.

        @  The 370-1128 SunLink Channel Adapter uses two slots. The Px03
           and Px04 jumpers must be unjumpered for both slots.
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the channel adapter and the
           CPU, or the channel adapter's throughput may be adversely
           affected.

        @@ 501-1154     Xylogics 450 SMD controller in Multibus-VME converter
           501-1166     Xylogics 451 SMD controller in Multibus-VME converter

        !  See "Important Note about ALM and MCP products", below.

        ~~ The 501-1383 TAAC-1 consumes three spaces (slots 10, 11, and
           12). Besides jumpering P1003 and P1004 as shown in the table
           above, P1103, P1104, and P1203 must be jumpered (P1204 does
           not exist).

    4/110

        board           slot:   1  2  3* Px03 Px04
        CPU 501-1199/1237 **    A  -  -   UN   UN
        MCP 501-1221 !          -  -  A   UN   UN
        ALM-2 501-1203 !        -  -  A   UN   UN
        color framebuffer @ @@  -  -  A   JU   UN
        2nd Ethernet 501-1153 * -  -  A   UN   UN
        IPC 501-1125            -  -  A   JU   UN

        *  If you wish to install a Multibus-VME converter-based board
           in slot 3, you just use converters 501-1054-04 rev A or later
           to avoid contention on the P2 memory bus.

        ** The CPU board covers slots 1 and 2 but only connects
           electrically to slot 1. Hence, treat slot 2 as empty (i.e.
           jump both P203 and P204).

        @  501-1116 "Sun-3" cg3 color
           501-1267 cg5 color

        @@ If a 501-1267 cg5 color framebuffer is installed, it must
           have its P2 bus disabled.

        !  See "Important Note about ALM and MCP products", below.

    4/260 using internal-connection-only or internal/external SCSI controller
          (for systems without a SCSI controller, use the "4/280 using
          external-connection-only SCSI controller" table below)

        board           slot:   1  2#~3# 4# 5# 6  7  8  9 10#11#12#Px03 Px04
        CPU 501-1274            A  -  -  -  -  -  -  -  -  -  -  -  UN   UN
        1st memory 501-1102 *   -  -  -  -  -  A  -  -  -  -  -  -  JU   JU
        2nd memory 501-1102 *   -  -  -  -  A  -  -  -  -  -  -  -  JU   JU
        3rd memory 501-1102 *   -  -  -  A  -  -  -  -  -  -  -  -  JU   JU
        4th memory 501-1102 *   -  -  A  -  -  -  -  -  -  -  -  -  JU   JU
        GP/GP+/GP2 ** % %%      -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        GB 501-1058 # %         -  -  -  -  -  -  -  -  -  -  A  -  JU   JU
        TAAC-1 501-1383 ~~      -  -  -  -  -  -  -  -  -  A  -  -  JU   JU
        ALM-1 501-1157 # !! !   -  -  -  -  -  -  -  -  -  -  -  A  UN   N/A
        SCSI 501-1149/1167/1170 -  -  -  -  -  -  A  -  -  -  -  -  UN   UN
        1st SCP 501-1158 #      -  D  A  B  C  -  E  F  -  -  -  -  UN   UN
        2nd SCP 501-1158 #      -  C  -  A  B  -  D  E  F  -  -  -  UN   UN
        1st MCP 501-1221 !      -  A  B  C  D  -  E  F  G  H  I  J  UN   UN
        2nd MCP 501-1221 !      -  -  A  B  C  -  D  E  F  G  H  I  UN   UN
        3rd MCP 501-1221 !      -  -  -  A  B  -  C  D  E  F  G  H  UN   UN
        4th MCP 501-1221 !      -  -  -  -  A  -  B  C  D  E  F  G  UN   UN
        1st ALM-2 501-1203 !    -  A  B  C  D  -  E  F  G  H  I  J  UN   UN
        2nd ALM-2 501-1203 !    -  -  A  B  C  -  D  E  F  G  H  I  UN   UN
        3rd ALM-2 501-1203 !    -  -  -  A  B  -  C  D  E  F  G  H  UN   UN
        4th ALM-2 501-1203 !    -  -  -  -  A  -  B  C  D  E  F  G  UN   UN
        1st SunLink Chnl Adpt @ -  A  A  C  C  -  D  D  F  F  H  H  UN   UN
                                -  -  B  B  -  -  -  E  E  G  G  -
        2nd SunLink Chnl Adpt @ -  -  -  A  A  -  B  B  D  D  F  F  UN   UN
                                -  -  -  -  -  -  -  C  C  E  E  -
        1st MAPKIT 501-1202 $$  -  A  A  C  C  -  D  D  F  F  H  H  UN   UN
                                -  -  B  B  -  -  -  E  E  G  G  -
        2nd MAPKIT 501-1202 $$  -  -  -  A  A  -  B  B  D  D  F  F  UN   UN
                                -  -  -  -  -  -  -  C  C  E  E  -
        2nd Ethernet 501-1153 # -  D  A  B  C  -  E  F  G  H  I  J  UN   UN
        1st IPC 501-1125        -  D  A  B  C  -  E  F  G  H  I  J  JU   UN
        2nd IPC 501-1125        -  C  -  A  B  -  D  E  F  G  H  I  JU   UN
        3rd IPC 501-1125        -  B  -  -  A  -  C  D  E  F  G  H  JU   UN
        4th IPC 501-1125        -  A  -  -  -  -  B  C  D  E  F  G  JU   UN
        1st 1/2" tape ## #      -  -  -  -  -  -  A  B  C  D  E  F  UN   UN
        2nd 1/2" tape ## #      -  -  -  -  -  -  -  A  B  C  D  E  UN   UN
        1st SMD @@ #            -  -  -  -  -  -  A  B  C  D  E  F  UN   UN
        2nd SMD @@ #            -  -  -  -  -  -  -  A  B  C  D  E  UN   UN
        cg3 color 501-1116 & %  -  J  A  B  C  -  D  E  F  G  H  I  JU   UN
        cg5 color 501-1267 & $  -  J  A  B  C  -  D  E  F  G  H  I  JU   UN w/o GP or GP+
         "    "    "   "   && $ -  H  A  B  C  -  D  E  F  -  -  -  JU   UN with GP or GP+
         "    "    "   "   %%   -  -  -  -  -  -  -  -  -  -  A  B  JU   UN with GP2

        #  If you wish to install a Multibus-VME converter-based board
           in slots 2-5, you just use converters 501-1054-04 rev A or
           later to avoid contention on the P2 memory bus.

           If you wish to install a Multibus-VME converted-based board
           in slots 10-12 and any combination of GP and GP boards are
           installed, you must use converters 501-1054-04 rev A or later
           to avoid contention on the GP/GB private bus.

        ## 501-1155     Xylogics 472 1/2" tape controller (6250 BPI)

           The older 501-1156 CPC 1/2" (1600 BPI) tape controller is not
           supported.

        ~  Avoid using slot 2 until absolutely necessary, to aid cooling
           of the CPU board. That is, if there is another slot available
           in which a board can be installed (even if it is not the most
           preferred slot) without impacting the functionality of
           another board, it should be installed in that slot instead of
           slot 2.

        ~~ The 501-1383 TAAC-1 consumes three spaces (slots 10, 11, and
           12). Besides jumpering P1003 and P1004 as shown in the table
           above, P1103, P1104, and P1203 must be jumpered (P1204 does
           not exist).

        *  501-1102     8M
           501-1254     32M

           There must always be a memory board in slot 6 and it must
           have a 220/270-ohm terminating resistor network installed at
           location 34-F for the 501-1102 8M board (see detailed
           description of board), or location 54-F for the 501-1254 32M
           board. Additional memory boards in slots 2-4 must NOT have
           the terminator installed.

        ** 501-1055     Graphics Processor
           501-1139     Graphics Processor Plus
           501-1268     Graphics Processor 2

        %  The 501-1268 GP2 will not function if any of the 501-1058
           graphics buffer, the 501-1116 Sun-3 color board (cg3), or the
           501-1014 Sun-2 color board are installed.

        %% The GP2 communicates with the 501-1267 cg5 over a private P2
           bus which must be enabled on the cg5 by a hardware switch
           setting. The cg5 must also be installed in slot 11 or 12.

        !  See "Important Note about ALM and MCP products", below.

        !! The 501-1157 ALM covers slots 11 and 12 but only connects
           electrically to slot 12. Hence, treat slot 11 as empty (i.e.
           jump both P1103 and P1104).

        &  The 501-1014 Sun-2 color framebuffer, 501-1116 cg3 color
           framebuffer, and 501-1267 cg5 color framebuffer are mutually
           exclusive.

        && When installed with either the 501-1055 graphics processor or
           the 501-1139 graphics processor plus, the cg5 may be
           installed in slots 2-9 only.

        $  The gp5's P2 bus must be disabled.

        $$ The 501-1202 MAPKIT covers two slots but only connects
           electrically to the slot nearest slot 1. Hence, treat the
           other slot as empty (i.e. jump both Px03 and Px04).
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the MAPKIT and the CPU, or
           the MAPKIT's throughput may be adversely affected.

        @  The 370-1128 SunLink Channel Adapter uses two slots. The Px03
           and Px04 jumpers must be unjumpered for both slots.
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the channel adapter and the
           CPU, or the channel adapter's throughput may be adversely
           affected.

        @@ 501-1154     Xylogics 450 SMD controller in Multibus-VME converter
           501-1166     Xylogics 451 SMD controller in Multibus-VME converter

    4/280 using external-connection-only SCSI controller

        board           slot:   1  2# 3# 4# 5# 6  7  8  9 10#11#12#Px03 Px04
        CPU 501-1100/1206       A  -  -  -  -  -  -  -  -  -  -  -  UN   UN
        1st memory 501-1102 *   -  -  -  -  -  A  -  -  -  -  -  -  JU   JU
        2nd memory 501-1102 *   -  A  -  -  -  -  -  -  -  -  -  -  JU   JU
        3rd memory 501-1102 *   -  -  A  -  -  -  -  -  -  -  -  -  JU   JU
        4th memory 501-1102 *   -  -  -  A  -  -  -  -  -  -  -  -  JU   JU
        GP/GP+/GP2 ** % %%      -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        GB 501-1058 # %         -  -  -  -  -  -  -  -  -  -  A  -  JU   JU
        TAAC-1 501-1383 ~~      -  -  -  -  -  -  -  -  -  A  -  -  JU   JU
        1st ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  -  -  A  UN   N/A
        2nd ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  -  A  -  UN   UN
        3rd ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        1st SCP 501-1158 #      -  A  B  C  D  -  E  -  -  -  -  -  UN   UN
        2nd SCP 501-1158 #      -  -  A  B  C  -  D  E  -  -  -  -  UN   UN
        1st MCP 501-1221 !      -  A  B  C  D  -  E  F  G  H  I  J  UN   UN
        2nd MCP 501-1221 !      -  -  A  B  C  -  D  E  F  G  H  I  UN   UN
        3rd MCP 501-1221 !      -  -  -  A  B  -  C  D  E  F  G  H  UN   UN
        4th MCP 501-1221 !      -  -  -  -  A  -  B  C  D  E  F  G  UN   UN
        1st ALM-2 501-1203 !    -  A  B  C  D  -  E  F  G  H  I  J  UN   UN
        2nd ALM-2 501-1203 !    -  -  A  B  C  -  D  E  F  G  H  I  UN   UN
        3rd ALM-2 501-1203 !    -  -  -  A  B  -  C  D  E  F  G  H  UN   UN
        4th ALM-2 501-1203 !    -  -  -  -  A  -  B  C  D  E  F  G  UN   UN
        1st SunLink Chnl Adpt @ -  A  A  C  C  -  D  D  F  F  H  H  UN   UN
                                -  -  B  B  -  -  -  E  E  G  G  -
        2nd SunLink Chnl Adpt @ -  -  -  A  A  -  B  B  D  D  F  F  UN   UN
                                -  -  -  -  -  -  -  C  C  E  E  -
        1st MAPKIT 501-1202 $$  -  A  A  C  C  -  D  D  F  F  G  G  UN   UN
                                -  -  B  B  -  -  -  E  E  -  -  -
        2nd MAPKIT 501-1202 $$  -  -  A  A  -  -  B  B  D  D  F  F  UN   UN
                                -  -  -  -  -  -  -  C  C  E  E  -
        SCSI 501-1138/1217      -  A  B  C  D  -  E  F  G  H  I  J  UN   UN
        cg3 color 501-1116 & %  -  A  B  C  D  -  E  F  G  H  I  J  JU   UN
        cg5 color 501-1267 & $  -  A  B  C  D  -  E  F  G  H  I  J  JU   UN w/o GP or GP+
         "    "    "   "   && $ -  A  B  C  D  -  E  F  G  -  -  -  JU   UN with GP or GP+
         "    "    "   "   %%   -  -  -  -  -  -  -  -  -  -  A  B  JU   UN with GP2
        2nd Ethernet 501-1153 # -  A  B  C  D  -  E  F  G  H  I  J  UN   UN
        1st IPC 501-1125        -  D  E  F  G  -  A  B  C  H  I  J  JU   UN
        2nd IPC 501-1125        -  C  D  E  F  -  -  A  B  G  H  I  JU   UN
        3rd IPC 501-1125        -  B  C  D  E  -  -  -  A  F  G  H  JU   UN
        4th IPC 501-1125        -  A  B  C  D  -  -  -  -  E  F  G  JU   UN
        1st 1/2" tape ## #      -  A  B  C  D  -  E  F  G  H  I  J  UN   UN
        2nd 1/2" tape ## #      -  -  A  B  C  -  D  E  F  G  H  I  UN   UN
        1st SMD @@ #            -  A  B  C  D  -  E  F  G  H  I  J  UN   UN
        2nd SMD @@ #            -  -  A  B  C  -  D  E  F  G  H  I  UN   UN

        #  If you wish to install a Multibus-VME converter-based board
           in slots 2-5, you just use converters 501-1054-04 rev A or
           later to avoid contention on the P2 memory bus.

           If you wish to install a Multibus-VME converted-based board
           in slots 10-12 and any combination of GP and GP boards are
           installed, you must use converters 501-1054-04 rev A or later
           to avoid contention on the GP/GB private bus.

        ## 501-1155     Xylogics 472 1/2" tape controller (6250 BPI)

           The older 501-1156 CPC 1/2" (1600 BPI) tape controller is not
           supported.

        *  501-1102     8M
           501-1254     32M

           There must always be a memory board in slot 6 and it must
           have a 220/270-ohm terminating resistor network installed at
           location 34-F for the 501-1102 8M board (see detailed
           description of board), or location 54-F for the 501-1254 32M
           board. Additional memory boards in slots 2-4 must NOT have
           the terminator installed.

        ** 501-1055     Graphics Processor
           501-1139     Graphics Processor Plus
           501-1268     Graphics Processor 2

        %  The 501-1268 GP2 will not function if any of the 501-1058
           graphics buffer, the 501-1116 Sun-3 color board (cg3), or the
           501-1014 Sun-2 color board are installed.

        %% The GP2 communicates with the 501-1267 cg5 over a private P2
           bus which must be enabled on the cg5 by a hardware switch
           setting. The cg5 must also be installed in slot 11 or 12.

        &  The 501-1014 Sun-2 color framebuffer, 501-1116 cg3 color
           framebuffer, and 501-1267 cg5 color framebuffer are mutually
           exclusive.

        && When installed with either the 501-1055 graphics processor or
           the 501-1139 graphics processor plus, the cg5 may be
           installed in slots 2-9 only.

        $  The gp5's P2 bus must be disabled.

        $$ The 501-1202 MAPKIT covers two slots but only connects
           electrically to the slot nearest slot 1. Hence, treat the
           other slot as empty (i.e. jump both Px03 and Px04).
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the MAPKIT and the CPU, or
           the MAPKIT's throughput may be adversely affected.

        @  The 370-1128 SunLink Channel Adapter uses two slots. The Px03
           and Px04 jumpers must be unjumpered for both slots.
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the channel adapter and the
           CPU, or the channel adapter's throughput may be adversely
           affected.

        @@ 501-1154     Xylogics 450 SMD controller in Multibus-VME converter
           501-1166     Xylogics 451 SMD controller in Multibus-VME converter

        !  See "Important Note about ALM and MCP products", below.

        ~~ The 501-1383 TAAC-1 consumes three spaces (slots 10, 11, and
           12). Besides jumpering P1003 and P1004 as shown in the table
           above, P1103, P1104, and P1203 must be jumpered (P1204 does
           not exist).

    4/280 using internal-connection-only or internal/external SCSI controller

        board           slot:   1  2# 3# 4# 5# 6  7  8  9 10#11#12#Px03 Px04
        CPU 501-1274            A  -  -  -  -  -  -  -  -  -  -  -  UN   UN
        1st memory 501-1102 *   -  -  -  -  -  A  -  -  -  -  -  -  JU   JU
        2nd memory 501-1102 *   -  A  -  -  -  -  -  -  -  -  -  -  JU   JU
        3rd memory 501-1102 *   -  -  A  -  -  -  -  -  -  -  -  -  JU   JU
        4th memory 501-1102 *   -  -  -  A  -  -  -  -  -  -  -  -  JU   JU
        GP/GP+/GP2 ** % %%      -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        GB 501-1058 # %         -  -  -  -  -  -  -  -  -  -  A  -  JU   JU
        TAAC-1 501-1383 ~~      -  -  -  -  -  -  -  -  -  A  -  -  JU   JU
        1st ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  -  -  A  UN   N/A
        2nd ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  -  A  -  UN   UN
        3rd ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        SCSI 501-1149/1167/1170 -  -  -  -  -  -  A  -  -  -  -  -  UN   UN
        1st SCP 501-1158 #      -  A  B  C  D  -  -  E  -  -  -  -  UN   UN
        2nd SCP 501-1158 #      -  -  A  B  C  -  -  D  E  -  -  -  UN   UN
        1st MCP 501-1221 !      -  A  B  C  D  -  -  E  F  G  H  I  UN   UN
        2nd MCP 501-1221 !      -  -  A  B  C  -  -  D  E  F  G  H  UN   UN
        3rd MCP 501-1221 !      -  -  -  A  B  -  -  C  D  E  F  G  UN   UN
        4th MCP 501-1221 !      -  -  -  -  A  -  -  B  C  D  E  F  UN   UN
        1st ALM-2 501-1203 !    -  A  B  C  D  -  -  E  F  G  H  I  UN   UN
        2nd ALM-2 501-1203 !    -  -  A  B  C  -  -  D  E  F  G  H  UN   UN
        3rd ALM-2 501-1203 !    -  -  -  A  B  -  -  C  D  E  F  G  UN   UN
        4th ALM-2 501-1203 !    -  -  -  -  A  -  -  B  C  D  E  F  UN   UN
        1st SunLink Chnl Adpt @ -  A  A  C  C  -  -  D  D  F  F  -  UN   UN
                                -  -  B  B  -  -  -  -  E  E  G  G
        2nd SunLink Chnl Adpt @ -  -  -  A  A  -  -  B  B  C  C  -  UN   UN
                                -  -  -  -  -  -  -  -  -  -  D  D
        1st MAPKIT 501-1202 $$  -  A  A  C  C  -  -  D  D  F  F  -  UN   UN
                                -  -  B  B  -  -  -  -  E  E  G  G
        2nd MAPKIT 501-1202 $$  -  -  A  A  -  -  -  B  B  C  C  -  UN   UN
                                -  -  -  -  -  -  -  -  -  -  D  D
        cg3 color 501-1116 & %  -  A  B  C  D  -  -  E  F  G  H  I  JU   UN
        cg5 color 501-1267 & $  -  A  B  C  D  -  -  E  F  G  H  I  JU   UN w/o GP or GP+
         "    "    "   "   && $ -  A  B  C  D  -  -  E  F  -  -  -  JU   UN with GP or GP+
         "    "    "   "   %%   -  -  -  -  -  -  -  -  -  -  A  B  JU   UN with GP2
        2nd Ethernet 501-1153 # -  A  B  C  D  -  -  E  F  G  H  I  UN   UN
        1st IPC 501-1125        -  A  B  C  D  -  -  E  F  G  H  I  JU   UN
        2nd IPC 501-1125        -  -  A  B  C  -  -  D  E  F  G  H  JU   UN
        3rd IPC 501-1125        -  -  -  A  B  -  -  C  D  E  F  G  JU   UN
        4th IPC 501-1125        -  -  -  -  A  -  -  B  C  D  E  F  JU   UN
        1st 1/2" tape ## #      -  -  -  -  -  -  -  A  B  C  D  E  UN   UN
        2nd 1/2" tape ## #      -  -  -  -  -  -  -  -  A  B  C  D  UN   UN
        1st SMD @@ #            -  -  -  -  -  -  -  A  B  C  D  E  UN   UN
        2nd SMD @@ #            -  -  -  -  -  -  -  -  A  B  C  D  UN   UN

        #  If you wish to install a Multibus-VME converter-based board
           in slots 2-5, you just use converters 501-1054-04 rev A or
           later to avoid contention on the P2 memory bus.

           If you wish to install a Multibus-VME converted-based board
           in slots 10-12 and any combination of GP and GP boards are
           installed, you must use converters 501-1054-04 rev A or later
           to avoid contention on the GP/GB private bus.

        ## 501-1155     Xylogics 472 1/2" tape controller (6250 BPI)

           The older 501-1156 CPC 1/2" (1600 BPI) tape controller is not
           supported.

        *  501-1102     8M
           501-1254     32M

           There must always be a memory board in slot 6 and it must
           have a 220/270-ohm terminating resistor network installed at
           location 34-F for the 501-1102 8M board (see detailed
           description of board), or location 54-F for the 501-1254 32M
           board. Additional memory boards in slots 2-4 must NOT have
           the terminator installed.

        ** 501-1055     Graphics Processor
           501-1139     Graphics Processor Plus
           501-1268     Graphics Processor 2

        %  The 501-1268 GP2 will not function if any of the 501-1058
           graphics buffer, the 501-1116 Sun-3 color board (cg3), or the
           501-1014 Sun-2 color board are installed.

        %% The GP2 communicates with the 501-1267 cg5 over a private P2
           bus which must be enabled on the cg5 by a hardware switch
           setting. The cg5 must also be installed in slot 11 or 12.

        &  The 501-1014 Sun-2 color framebuffer, 501-1116 cg3 color
           framebuffer, and 501-1267 cg5 color framebuffer are mutually
           exclusive.

        && When installed with either the 501-1055 graphics processor or
           the 501-1139 graphics processor plus, the cg5 may be
           installed in slots 2-9 only.

        $  The gp5's P2 bus must be disabled.

        $$ The 501-1202 MAPKIT covers two slots but only connects
           electrically to the slot nearest slot 1. Hence, treat the
           other slot as empty (i.e. jump both Px03 and Px04).
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the MAPKIT and the CPU, or
           the MAPKIT's throughput may be adversely affected.

        @  The 370-1128 SunLink Channel Adapter uses two slots. The Px03
           and Px04 jumpers must be unjumpered for both slots.
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the channel adapter and the
           CPU, or the channel adapter's throughput may be adversely
           affected.

        @@ 501-1154     Xylogics 450 SMD controller in Multibus-VME converter
           501-1166     Xylogics 451 SMD controller in Multibus-VME converter

        !  See "Important Note about ALM and MCP products", below.

        ~~ The 501-1383 TAAC-1 consumes three spaces (slots 10, 11, and
           12). Besides jumpering P1003 and P1004 as shown in the table
           above, P1103, P1104, and P1203 must be jumpered (P1204 does
           not exist).

    4/280 using external-connection-only SCSI controller and leaving
          slots 7-9 for non-Sun boards that use P2 bus signals

        board           slot:   1  2# 3# 4# 5# 6  7  8  9 10#11#12#Px03 Px04
        CPU 501-1274            A  -  -  -  -  -  -  -  -  -  -  -  UN   UN
        1st memory 501-1102 *   -  -  -  -  -  A  -  -  -  -  -  -  JU   JU
        2nd memory 501-1102 *   -  A  -  -  -  -  -  -  -  -  -  -  JU   JU
        3rd memory 501-1102 *   -  -  A  -  -  -  -  -  -  -  -  -  JU   JU
        4th memory 501-1102 *   -  -  -  A  -  -  -  -  -  -  -  -  JU   JU
        GP/GP+/GP2 ** % %%      -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        GB 501-1058 # %         -  -  -  -  -  -  -  -  -  -  A  -  JU   JU
        TAAC-1 501-1383 ~~      -  -  -  -  -  -  -  -  -  A  -  -  JU   JU
        1st ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  -  -  A  UN   N/A
        2nd ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  -  A  -  UN   UN
        3rd ALM-1 501-1165 # !  -  -  -  -  -  -  -  -  -  A  -  -  UN   UN
        1st SCP 501-1158 #      -  A  B  C  D  -  -  -  -  E  F  G  UN   UN
        2nd SCP 501-1158 #      -  -  A  B  C  -  -  -  -  D  E  F  UN   UN
        1st MCP 501-1221 !      -  A  B  C  D  -  -  -  -  E  F  G  UN   UN
        2nd MCP 501-1221 !      -  -  A  B  C  -  -  -  -  D  E  F  UN   UN
        3rd MCP 501-1221 !      -  -  -  A  B  -  -  -  -  C  D  E  UN   UN
        4th MCP 501-1221 !      -  -  -  -  A  -  -  -  -  B  C  D  UN   UN
        1st ALM-2 501-1203 !    -  A  B  C  D  -  -  -  -  E  F  G  UN   UN
        2nd ALM-2 501-1203 !    -  -  A  B  C  -  -  -  -  D  E  F  UN   UN
        3rd ALM-2 501-1203 !    -  -  -  A  B  -  -  -  -  C  D  E  UN   UN
        4th ALM-2 501-1203 !    -  -  -  -  A  -  -  -  -  B  C  D  UN   UN
        1st SunLink Chnl Adpt @ -  A  A  C  C  -  -  -  -  D  D  -  UN   UN
                                -  -  B  B  -  -  -  -  -  -  E  E
        2nd SunLink Chnl Adpt @ -  -  -  A  A  -  -  -  -  B  B  -  UN   UN
                                -  -  -  -  -  -  -  -  -  -  C  C
        1st MAPKIT 501-1202 $$  -  A  A  C  C  -  -  -  -  D  D  -  UN   UN
                                -  -  B  B  -  -  -  -  -  -  E  E
        2nd MAPKIT 501-1202 $$  -  -  A  A  -  -  -  -  -  B  B  -  UN   UN
                                -  -  -  -  -  -  -  -  -  -  C  C
        SCSI 501-1138/1217      -  A  B  C  D  -  -  -  -  E  F  G  UN   UN
        cg3 color 501-1116 & %  -  A  B  C  D  -  -  -  -  E  F  G  JU   UN
        cg5 color 501-1267 & $  -  A  B  C  D  -  -  -  -  E  F  G  JU   UN w/o GP or GP+
         "    "    "   "   && $ -  A  B  C  D  -  -  -  -  -  -  -  JU   UN with GP or GP+
         "    "    "   "   %%   -  -  -  -  -  -  -  -  -  -  A  B  JU   UN with GP2
        2nd Ethernet 501-1153 # -  A  B  C  D  -  -  -  -  E  F  G  UN   UN
        1st IPC 501-1125        -  A  B  C  D  -  -  -  -  E  F  G  JU   UN
        2nd IPC 501-1125        -  -  A  B  C  -  -  -  -  D  E  F  JU   UN
        3rd IPC 501-1125        -  -  -  A  B  -  -  -  -  C  D  E  JU   UN
        4th IPC 501-1125        -  -  -  -  A  -  -  -  -  B  C  D  JU   UN
        1st 1/2" tape ## #      -  A  B  C  D  -  -  -  -  E  F  G  UN   UN
        2nd 1/2" tape ## #      -  -  A  B  C  -  -  -  -  D  E  F  UN   UN
        1st SMD @@ #            -  A  B  C  D  -  -  -  -  E  F  G  UN   UN
        2nd SMD @@ #            -  -  A  B  C  -  -  -  -  D  E  F  UN   UN

        #  If you wish to install a Multibus-VME converter-based board
           in slots 2-5, you just use converters 501-1054-04 rev A or
           later to avoid contention on the P2 memory bus.

           If you wish to install a Multibus-VME converted-based board
           in slots 10-12 and any combination of GP and GP boards are
           installed, you must use converters 501-1054-04 rev A or later
           to avoid contention on the GP/GB private bus.

        ## 501-1155     Xylogics 472 1/2" tape controller (6250 BPI)

           The older 501-1156 CPC 1/2" (1600 BPI) tape controller is not
           supported.

        *  501-1102     8M
           501-1254     32M

           There must always be a memory board in slot 6 and it must
           have a 220/270-ohm terminating resistor network installed at
           location 34-F for the 501-1102 8M board (see detailed
           description of board), or location 54-F for the 501-1254 32M
           board. Additional memory boards in slots 2-4 must NOT have
           the terminator installed.

        ** 501-1055     Graphics Processor
           501-1139     Graphics Processor Plus
           501-1268     Graphics Processor 2

        %  The 501-1268 GP2 will not function if any of the 501-1058
           graphics buffer, the 501-1116 Sun-3 color board (cg3), or the
           501-1014 Sun-2 color board are installed.

        %% The GP2 communicates with the 501-1267 cg5 over a private P2
           bus which must be enabled on the cg5 by a hardware switch
           setting. The cg5 must also be installed in slot 11 or 12.

        &  The 501-1014 Sun-2 color framebuffer, 501-1116 cg3 color
           framebuffer, and 501-1267 cg5 color framebuffer are mutually
           exclusive.

        && When installed with either the 501-1055 graphics processor or
           the 501-1139 graphics processor plus, the cg5 may be
           installed in slots 2-9 only.

        $  The gp5's P2 bus must be disabled.

        $$ The 501-1202 MAPKIT covers two slots but only connects
           electrically to the slot nearest slot 1. Hence, treat the
           other slot as empty (i.e. jump both Px03 and Px04).
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the MAPKIT and the CPU, or
           the MAPKIT's throughput may be adversely affected.

        @  The 370-1128 SunLink Channel Adapter uses two slots. The Px03
           and Px04 jumpers must be unjumpered for both slots.
           Additionally, do not place a 1/2" tape controller or an SMD
           disk controller in a slot between the channel adapter and the
           CPU, or the channel adapter's throughput may be adversely
           affected.

        @@ 501-1154     Xylogics 450 SMD controller in Multibus-VME converter
           501-1166     Xylogics 451 SMD controller in Multibus-VME converter

        !  See "Important Note about ALM and MCP products", below.

        ~~ The 501-1383 TAAC-1 consumes three spaces (slots 10, 11, and
           12). Besides jumpering P1003 and P1004 as shown in the table
           above, P1103, P1104, and P1203 must be jumpered (P1204 does
           not exist).


IMPORTANT NOTE ABOUT ALM AND MCP PRODUCTS

   The 501-1203 ALM-2 shares VME vector interrupt assignments with the
501-1157 (-1165 also?) ALM-1 and the 501-1221 MCP. The ALM-2 also shares
VME address space with the MCP. There may also be a problem with
physical space in the chassis.

   If three ALM-1s with their associated MUX boxes are already
installed, there is no room to mount the ALM-2's Device Connector
Assembly (DCA). Fortunately, it is possible to mount the DCA to the
wall, floor, or anywhere else convenient.

   The ALM-2 and the MCP have exactly the same vector interrupt
assignments. The ALM-1 has vector interrupt assignments that occupy the
same range but are in the opposite order, as shown below:

        board number    device entry    ALM-1 vector    ALM-2/MCP vector
        ------------    ------------    ------------    ----------------
            1st              0              0x88            0x8B
            2nd              1              0x89            0x8A
            3rd              2              0x8A            0x89
            4th              3              0x8B            0x88

   To avoid conflicts, follow these rules:

   1) No more than four ALM-1, ALM-2, or MCP boards total may be
installed in a single cardcage.

   2) When installing ALM-2s or MCPs, the boards must be installed in
the proper address order, counting all boards of either type previously
installed. This ensures that no ALM-2s or MCPs will attempt to use the
same vector interrupt. For example, if an ALM-2 is installed and you
wish to install an MCP, it must be installed as the *second* MCP, not
the first. If it is installed as the first, it will attempt to use the
same vector interrupt as the existing ALM-2.

   3) Because the ALM-1 vector interrupt assignments are the reverse of
the others, any ALM-1 boards must be installed in their normal order,
counting *only* ALM-1s. This ensures that as long as no more than four
boards total of any of these kinds are installed, the ALM-1s will never
use the same part of the range as the ALM-2s and MCPs.

   4) Additionally, the ALM-2 and MCP occupy identical addresses in the VME
address space, and both use /dev entries of mcp0 through mcp3. Each
additional board installed uses the next available entry, regardless of
the type (ALM-2 or MCP, but not ALM-1) of the boards installed
previously. The addresses must also be set (via jumpers or switches?) on
the boards -- as stated in rule 2, the board must be installed counting
all boards of either type previously installed.

   5) For deskside systems that support the ALM-1, only one such board
may coexist in the cardcage with ALM-2 and/or MCP boards.



              END OF PART VI OF THE SUN HARDWARE REFERENCE